Installation Guide
Table Of Contents
- 页 1
- 书签7AD8A58F A. B. C. D. E.
- 书签AD288FB0 Here's how to remove the old sink:
- 书签ED6989BA Step 2 \(Out With The Old\)
- 书签2246376C Shut off the water supply valves. Disconnect the water supply fittings. Disconnect the drain fittings. From the underside of the sink, with your flashlight and long screwdriver, loosen and remove the frame clamps or rim fasteners. Lift the entire sink out of the countertop.
- 书签59306241 Position template on countertop. Locate the template front to rear, so that sink will not interfere with the cabinet.
- 书签A3F60086 NOTE : Skip step 2 if this is a new installation.
- 书签D2D0FFCE Note: The granite composite kitchen sink provided is considered a universal mount granite composite kitchen sink - it can either be installed as an under-mount with the counter-top overhang or a traditional top-mount. For top-mount installations, please follow top-mount sinks installation. For under-mount installations, please follow under-mount sinks installation.
- 书签62A27E3D The warranty will be voided if these installation instructions are not followed.
- 书签17D14DBE Remember, it is your responsibility to follow all local plumbing and building codes.
- 书签1740922F — —
- 书签003C1B93 1
- 书签78E32494 RECOMMENDED TOOLS
- 书签68D3C45E For safety and ease of installation, factory recommends the use of the helpful tools above.
- 书签5295911E 1
- 书签500F104C Drill and Drill Bit
- 书签FB3208D0 Granite Composite Work Station Kitchen Sink Installation Instructions
- 书签A75653D0 4
- 书签74CF05A6 Silicone Caulk and Caulk Gun
- 书签755DA5AF 3
- 书签0F9C4A76 Pencil
- 书签4CE40D6D 5
- 书签30E40346 6
- 书签381AA543 Flashlight
- 书签AECD8228 7
- 书签48CEB9BD Safety Glasses
- 书签A3993C57 8
- 书签5460DFB3 Gloves
- 书签FD03D945 Adjustable Wrench
- 书签A1A590E0 6
- 书签51735C05 5
- 书签BD7CEEEA 7
- 书签AAF81680 8
- 书签398E604D — —
- 书签3587EFCD 2
- 书签0483A27B — —
- 书签F6449F62 3
- 书签B9E1C696 — —
- 书签713183BA 4
- 书签2ACB3C8E Top-mount Sinks Installation
- 书签3980B91B Step 1
- 书签C2BA16E1 *BEFORE INSTALLING THE GRANITE COMPOSITE KITCHEN SINK, INSPECT IT FOR DAMAGE. DO NOT INSTALL A DAMAGED UNIT.
- 书签B9B5EE0F Faucet Hole Drillings
- 书签46BFC441 Factory has pre-scored additional faucet holes \( 3 \) on the bottom of sink.
- 书签64F0451C Step 1
- 书签47DB454E Factory has included a 38mm \( 1-1/2" \) drill bit.
- 书签500DDB17 Step 2
- 书签6670817D Using provided drill bit, drill from the bottom using the pre-scored holes for any additional faucet holes needed.
- 书签3514374D Step 3
- 书签178D14B8 Step 4
- 书签C2CEA523 Apply silicone adhesive caulk around the perimeter of the countertop edge.
- 书签B72EAB45 Step 4
- 书签1D30FDDD Step 3
- 书签C9FE2146 2
- 书签46DDF543 Long Shank Flat Screwdriver
- 书签F295337B 1
- 书签3315BBF6 4
- 书签4D5817F8 3
- 书签3217858D 2
- 书签E9EE9C16 Step 2
- 书签01E73CBE Step 1
- 书签80E5B78B Countertop
- 书签3190803A Trace Completely Around Edge Of Cut-out Template
- 书签C5A1DC61 Step 5
- 书签74142FC4 Lower sink into the cutout and press firmly into the silicone. Make sure the sink is level and aligned.
- 书签331DA0A9 Step 6
- 书签B5B3EF80 Insert L-bracket into oval slot of 3 hole bracket. Tighten bracket against underside of countertop using supplied bolts. DO NOT OVERTIGHTEN.
- 书签E77C0F6C Step 7
- 书签3C6BF21E Remove any excess silicone adhesive caulk.
- 书签095C66E7 Step 8
- 书签6A043E90 With the sink in place attach the L-brackets and tighten. DO NOT OVERTIGHTEN.
- 书签B959555B Step 6
- 书签E14E5CE7 Step 3
- 书签88DCE524 Trace around the outside of the template. Cut along the inside of this line. Set sink in opening to see if it fits properly. Remove sink.
- 书签A7983322 1-1/2"\(38mm\)
- 书签80A3E932 Carton includes: Work Station Sink, Colander, Drying Rack, Sink Grid, Cutting Board, L-Bracket for Top-Mount Installation, Slotted Bracket for Under-Mount Installation & Installation Instructions.
- 书签62D4DCF9 L-Bracket
- 书签F2481D6F Screw
- 书签69073971 L-Bracket
- 书签D909A10A Screw
- 书签001C3359 Attach Accessories
- 书签350D59E4 \(A\)Locknut
- 书签EDD04CD5 \(B\)Rubber Washer
- 书签63CD8920 \(E\)Tailpiece Washer
- 书签97E5C456 \(D\)Slip Nut
- 书签6830A514 \(F\)Strainer Flange
- 书签75CCF283 \(C\)Friction Washer
- 书签CF259757 Sink
- 书签EA53345A \(G\)Plumbers' Putty
- 书签6407854B Connect Faucet Supplies and Drain Fittings
- 书签935E1B17 Plumbers Putty
- 书签F0894E3C Use Teflon tape at all threaded water connections to avoid leaks. Connect the drain trap fittings. Connect the water supply valves to the faucet. Turn on the water supply valves and check for leaks in the following locations: Supply lines to the faucet; Supply lines to the water supply valves. Fill the sink bowl with water and check around the drain flange\(s\) for moisture and for water dripping onto the bottom of the cabinet. Release water from sink and tighten any leaky connections found.
- 书签E6ACCAE9 New Accessory Installation: Follow the installation instructions provided with the new accessory. Reinstalling Old Accessories: Clean all old sealant from accessory. Reinstall using fresh plumber's putty or silicone sealant. Flexible Supply Lines: Measure from the bottom of the counter-top to the water supply valve. Add 4" to the measurement to allow for movement. Use Teflon tape in all threaded water connections to avoid leaks. Sink Strainer Installation: Place sealant on bottom of \(F\) strainer flange \(to seal properly\) and place in sink opening. From underneath, place \(B\) rubber washer and \(C\) friction washer onto \(F\) strainer flange, then screw on the \(A\) lock nut while holding the \(F\) strainer flange firmly in place. Tighten securely. Place \(E\) tail piece washer \(flat side facing up\) into the \(D\) slip nut. Screw the \(D\) slip nut onto the \(F\) strainer flange.
- 页 2
- 书签FE1E3E1E Compass Manufacturing International warrants to the original purchaser of an Compass Manufacturing International granite composite kitchen sink that Compass Manufacturing International will, at its option, replace or repair, without charge, such product if it fails due to a manufacturing defect for a lifetime of normal residential use. Product replacement does not include transportation cost or labor installation cost. This warranty covers only granite composite kitchen sinks installed in a conventional counter-top surface and granite composite kitchen sinks installed in a conventional solid surface counter-top and applies to residential installations only. Compass Manufacturing International reserves the right to examine product in question and its installation prior to replacement. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
- 书签66AE6637 Compass Manufacturing International Limited Lifetime Granite Composite Kitchen Sink Warranty
- 书签8498EF66 — —
- 书签E33D532B 8
- 书签9C3C09E8 — —
- 书签DC0467B2 7
- 书签12EF36DC — —
- 书签F90E465A 5
- 书签FD975C5E Under-mount Sinks Installation
- 书签96233CA2 Revised 11/12/20
- 书签D8FE0070 — —
- 书签687D2AA7 6
- 书签55188720 Granite Composite Kitchen Sinks Care And Cleaning
- 书签880D185B Step 4
- 书签DD3944D8 Fasten the slotted brackets \(Included\) on the underside of the countertop loosely. Please use the screws recommended by the countertop supplier \(these screws are not included\).
- 书签89968966 Step 4
- 书签EAE2AD2C Step 3
- 书签EAE1E4F7 Trace around the outside of the template. Cut along the inside of this line. Set sink in opening to see if it fits properly. Remove sink.
- 书签E499AE81 A. B. C. D. E.
- 书签8D1E3611 Here's how to remove the old sink:
- 书签596705CF Step 2 \(Out With The Old\)
- 书签1FECDE41 Shut off the water supply valves. Disconnect the water supply fittings. Disconnect the drain fittings. From the underside of the sink, with your flashlight and long screwdriver, loosen and remove the frame clamps or rim fasteners. Lift the entire sink out of the countertop.
- 书签74300AAD Step 2
- 书签7F92480B Countertop
- 书签4D086867 Step 1
- 书签604361C6 Trace Completely Around Edge Of Cut-out Template
- 书签31F517D3 Step 1
- 书签4AE519C5 Position template on countertop. Locate the template front to rear, so that sink will not interfere with the cabinet.
- 书签8B62E848 NOTE : Skip step 2 if this is a new installation.
- 书签8A23BEF3 Step 5
- 书签5799CDFD Use silicone adhesive caulk. Apply a bead evenly all around the top of sink flange.
- 书签2E452387 Step 6
- 书签1E3465AA Position sink and align in countertop opening.
- 书签81F48701 Step 5
- 书签447B56E5 Step 7
- 书签7A87462E Tighten slotted brackets until mounting brackets are snug.
- 书签2055B762 Step 8
- 书签75D9ABFE Do not over tighten slotted brackets. Note: Remove excess silicone caulk.
- 书签25245540 NOTE: Clean sink before first use. *Wash sink with warm water and wipe dry using soft cloth. *Use only non abrasive cleaners or detergents on sink. *Use only non abrasive cloths, soft sponge, \( Magic Eraser \) etc. HINT: Rinse and dry surface with a soft cloth after each use.
- 书签E9607930 Step 7
- 书签B1E32AEB Not Included
- 书签CF8512E7 Slotted Bracket Included
- 书签4DDD8F99 Not Included
- 书签D954A65A Attach Accessories
- 书签7A8E50AB \(A\)Locknut
- 书签754ED36C \(B\)Rubber Washer
- 书签26CCFA5C \(E\)Tailpiece Washer
- 书签667C9C4A \(D\)Slip Nut
- 书签FB504F52 \(F\)Strainer Flange
- 书签CF2B5603 \(C\)Friction Washer
- 书签8723B94A Sink
- 书签C58DF3B0 \(G\)Plumbers' Putty
- 书签335BD132 Connect Faucet Supplies and Drain Fittings
- 书签83E1E1B4 Plumbers Putty
- 书签99D26044 Use Teflon tape at all threaded water connections to avoid leaks. Connect the drain trap fittings. Connect the water supply valves to the faucet. Turn on the water supply valves and check for leaks in the following locations: Supply lines to the faucet; Supply lines to the water supply valves. Fill the sink bowl with water and check around the drain flange\(s\) for moisture and for water dripping onto the bottom of the cabinet. Release water from sink and tighten any leaky connections found.
- 书签8D02C440 New Accessory Installation: Follow the installation instructions provided with the new accessory. Reinstalling Old Accessories: Clean all old sealant from accessory. Reinstall using fresh plumber's putty or silicone sealant. Flexible Supply Lines: Measure from the bottom of the counter-top to the water supply valve. Add 4" to the measurement to allow for movement. Use Teflon tape in all threaded water connections to avoid leaks. Sink Strainer Installation: Place sealant on bottom of \(F\) strainer flange \(to seal properly\) and place in sink opening. From underneath, place \(B\) rubber washer and \(C\) friction washer onto \(F\) strainer flange, then screw on the \(A\) lock nut while holding the \(F\) strainer flange firmly in place. Tighten securely. Place \(E\) tail piece washer \(flat side facing up\) into the \(D\) slip nut. Screw the \(D\) slip nut onto the \(F\) strainer flange.
- 书签649B2BC1 warranty@cmiproduct.com
- 书签5C2CA4C8 Call toll-free 1-800-626-3525 or email warranty@cmiproduct.com, our technical service department is available to assist you.
