CN MUC Document type: Reference Manual Document ID: A30880-A10-A001-XX-D376 AT command set for XX Siemens mobile phones and modems Release/Version: Master R75 Date: 29.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Issued by Comneon GmbH & Co OGH CN MUC Grillparzerstrasse 12a D-81675 Munich Copyright Comneon 2004 All Rights Reserved. Comneon GmbH & Co OGH _________________________________________________________________________________________ Document No.: Revision: Revision Date: A30880-A10-A001-XXD376 Master R75 29.
Table of Contents Table of Contents ........................................................................................................................................................... i 1 General information .............................................................................................................................................. 4 1.2 Abbreviations and glossary ........................................................................................................................
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 5.6 Use of Siemens specific Key O/o ............................................................................................................. 144 5.7 Use of Siemens specific Key X/x ............................................................................................................. 144 5.8 List of Commands related to CSCS / UCS2 .......................
AT command set for XX Siemens mobile phones and modems __________________________________________________________________________________________ List of Tables Table 2-1: Supported 3GPP TS 27.007 commands [15] ............................................................................................... 8 Table 2-2: Supported 3GPP TS 27.005 commands [14] ...............................................................................................
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 1 General information This document constitutes the manual reference to the AT command set supported by Siemens mobile phones. 1.
AT command set for XX Siemens mobile phones and modems “…” @ Comma (,) Spaces < .. > […] parameter. In parameter type commands, this value should be used in factory settings which are configured by V.250 command &F0. In action type commands, this value should be used when parameter is not given Double quotes (“) are used to indicate text strings Symbols (e. g.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ [9] GSM 04.11: "Digital cellular telecommunication system (Phase 2+); Point-to-Point (PP) Short Message Service (SMS) support on mobile radio interface". [10]GSM 05.08: "Digital cellular telecommunication system (Phase 2+); Radio subsystem link control". [11]GSM 11.
AT command set for XX Siemens mobile phones and modems AT+CEER AT+CGACT AT+CGANS Query the reason for disconnection of last call PDP context activate or deactivate Manual response to a network request for PDP context activation AT+CGATT GPRS attach or detach AT+CGAUTO Auto response to a network request for PDP context activation AT+CGCLASS GPRS mobile station class AT+CGCMOD PDP context Modify AT+CGDATA Enter data state AT+CGDCONT Define PDP Context AT+CGDSCONT Define Secondary PDP Context AT+CGEQMIN 3G Qu
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+CPBR Read a telephone-book entry AT+CPBS Select a telephone book AT+CPBW Write a telephone-book entry AT+CPIN Enter PIN and query lock AT+CPOL AT+CPUC Preferred operator list Price per unit and currency table AT+CPWD AT+CR AT+CRC AT+CREG AT+CRLP AT+CRMP Change password to a lock Service reporting control Cellular result codes Network registration Sele
AT command set for XX Siemens mobile phones and modems AT+CMMS AT+CMSS AT+CNMA AT+CNMI AT+CPMS AT+CSCA AT+CSCB AT+CSMS More (Short) Message to Send Send an SMS from the SMS memory Acknowledgment of a short message directly output New Preferred SMS message storage Address of the SMS service centre Select cell broadcast messages Selection of message service Message sending and writing Message sending and writing Message receiving and reading 71 72 72 Message receiving and reading General configuration Mes
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Table 2-3 lists all the supported AT commands for FAX services in alphabetical order: Command AT+FBADLIN AT+FBADMUL AT+FBOR AT+FCIG AT+FCLASS AT+FCQ AT+FCR AT+FDCC AT+FDFFC AT+FDIS AT+FDR AT+FDT AT+FET AT+FK AT+FLID AT+FMDL AT+FMFR AT+FOPT AT+FPHCTO AT+FREV AT+FRH AT+FRM AT+FRS AT+FTH AT+FTM AT+FTS AT+FVRFC Function Define or read number of bad lines Define, read
AT command set for XX Siemens mobile phones and modems AT^SACD AT^SACM AT^SADT AT^SBLK AT^SBMH AT^SBNR AT^SBNW AT^SCCM AT^SCID AT^SCKA AT^SCKS AT^SCNI AT^SDBR AT^SDLD AT^SDLY AT^SGAUTH AT^SGDCONT AT^SGDV AT^SICO AT^SIFS AT^SKPD AT^SLCK AT^SLNG AT^SMGL AT^SMGO AT^SMGR AT^SMSO AT^SNFS AT^SNFV AT^SOBX AT^SPBA AT^SPBC AT^SPBG AT^SPBS AT^SPIC AT^SPLM AT^SPLR AT^SPLW AT^SPST AT^SPTT AT^SPWD AT^SQWE AT^SRMP AT^SSET AT^SSTK AT^STRC AT^SVMC Accessory Data Output ACM (accumulated call meter) and ACMmax Application D
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 2.2 The AT command set GSM mobile telephones and modems can be operated via Remote Control using a serial interface (data cable or infrared connection). Remote control is implemented by means of AT+C commands according to the 3GPP TS 27.007 [15] and 3GPP TS 27.005 [14] specifications, as well as several manufacturer-specific AT commands.
AT command set for XX Siemens mobile phones and modems AT+CGATT AT+CGCMOD AT+CHLD AT+CMGC AT+CMGD 2.2.3 AT+CMGL AT+CMGR AT+CMGS AT+CMGW AT+CMSS ATA ATD AT+COPS AT+CPBR AT+CPBS AT+CPBW AT+VTS Generic TA control commands according to ITU-T V.250 The generic TA control commands (“Hayes standard commands”) correspond to the commands of AT Hayes compatible modems. All commands in Table 2-7 expect a numeric argument; if this argument is omitted, the default of 0 is assumed. Command Function AT...
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Command Function ATQ1 ATSn=x ATV0 ATV1 ATX Suppress acknowledgments (responses or messages) Write value x to S register n (modem command according to [16]) Display value of S register n (modem command according to [16]) Note: This type of mobile phone does not allow the values of all S registers to be displayed with a single command Display acknowledgments a
AT command set for XX Siemens mobile phones and modems Command Function AT&F[0] Resets all current parameters of the following AT commands to their factory profile: ATE, ATQ, ATV, AT&\Q, AT&C, AT&D, AT&S , AT+VTS, ATX AT+CAOC, AT+CMEE, AT+CPMS, AT+CSCS, AT+CBST, AT+CMER, AT+CPBS, AT+CSMS, AT+CCWA, AT+CEER, AT+CLIP, AT+CMEC, AT+CNMI, AT+COLP, AT+COPS, AT+CPOL, AT+CR,, AT+CRC, AT+CREG, AT+CRLP, AT+CSSN, AT^SACM, AT^SCKS, AT^SMGO, S parameters If GPRS is supported then also the following GPRS commands a
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ The ATD command The ATD command is a special command in that all characters specified in the same line (or up to a semicolon) are considered part of the number to dial.
AT command set for XX Siemens mobile phones and modems To dial for a CSD data call or a FAX call the trailing semicolon (;) must not be used The following syntax for a CSD data/Fax call is supported: ATD Dial command for modem and fax calls The selection if either a data or fax call is set up depends on the setting of the fax class. See the command AT+FCLASS for further details. T P I Tone or pulse dialling.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 1-3 PDP context identifier Notes for GPRS calls: 1) The ATD command for GPRS always includes an attach if the mobile is currently detached. The attach may last for some time (up to 60 seconds). During attach the command is interruptible 2) If no is given in the ATD command a predefined PDP context without an Access Point Name is used for dialing.
AT command set for XX Siemens mobile phones and modems AT+CGMI Parameter: Name of manufacturer (SIEMENS) AT+CGMM AT+CGMM Issue model ID code Test command Response: AT+CGMM=? OK Test command Response: AT+CGMM Parameter: Name of telephone (MOBILE) AT+CGMR AT+CGMR Output the GSM telephone version Test command: Response: AT+CGMR=? OK Execute command: Response: AT+CGMR Parameter: Version of the telephone software AT+C
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ OK/ERROR/+CME ERROR Parameter: string of characters representing keys (see section 5.5 for a list of implemented keys)
AT command set for XX Siemens mobile phones and modems Read command Response: AT+WS46? OK/ERROR/+CME ERROR Parameter: See Test command Write command AT+WS46=[] Response: OK/ERROR/+CME ERROR Parameter: 2.3.2 See Test command Call control commands This section provides the descriptions of commands related to call control.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+CR= OK/ERROR/+CME ERROR Parameter: See Test command Unsolicited Result Code +CR: Parameter: ASYNC SYNC REL ASYNC REL SYNC GPRS For a detailed description refer to [15] AT+CRC AT+CRC Cellular result codes Test command Response: AT+CRC=? +CRC: (list of supported s) OK/ERROR/+CME ERROR Parameter 0 1 disables r
AT command set for XX Siemens mobile phones and modems 2.3.3 Network service related commands This section provides the descriptions of commands related to network service.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 0 1 2 3 4 1 2 4 7 8 16 32 64 128 X
AT command set for XX Siemens mobile phones and modems 4 7 8 16 32 64 128 X 0 1 2 0 1 Fax Voice, Data and Fax (default) SMS data circuit sync data circuit async dedicated packet access dedicated PAD access combination of some of the above classes, e.g.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Test command Response: AT+CLCC=? OK Execute command Response: AT+CLCC [+CLCC: ,,,,,,,,- ][ +CLCC: ,,,,, ,,, [...]]] OK/ERROR/+CME ERROR Parameter: Indicates the call identification number as described in subclause 4.5.5.1 of the GSM 02.
AT command set for XX Siemens mobile phones and modems Test command Response: AT+CLCK=? +CLCK: (list of supported s) OK/ERROR/+CME ERROR Parameter: AB AC AG AI AO CS FD IR OI OX PC PF PN PP PS PU SC All barring services All incoming barring services All outgoing barring services BAIC (bar all incoming calls) BAOC (bar all outgoing calls) All incoming barring services FDN lock BIC-Roam (bar incoming calls when roaming outside the home country) BOIC (bar outgoing international calls) BOIC-exHC
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ _________________________________________________________________________________________ Document No.: Revision: Revision Date: A30880-A10-A001-XXD376 Master R75 29.
AT command set for XX Siemens mobile phones and modems AT+CLIP AT+CLIP Calling Line Identification Presentation Test command Response: AT+CLIP=? +CLIP: (list of supported s) OK/ERROR/+CME ERROR Parameter: 0 1 Suppresses Unsolicited result codes Displays Unsolicited result codes Read command Response: AT+CLIP? +CLIP: , OK/ERROR/+CME ERROR Parameter See Test command 0 CLIP not booked 1 CLIP booked 2 Unknown Write command AT+CLIP=[] Response: OK/ERROR/+CME ERROR Parame
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ CLIR suppression (not incognito) 2 Read command Response: AT+CLIR? +CLIR: , OK/ERROR/+CME ERROR Parameter: See Test command 0 CLIR not provisioned (not incognito) 1 CLIR provisioned in permanent mode (incognito) 2 Unknown 3 CLIR mode presentation temporarily restricted (next call incognito) 4 CLIR mode presentation temporarily allowed (next call not inc
AT command set for XX Siemens mobile phones and modems 2 Unknown Write command AT+COLP=[] Response.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Parameter: See Test command See Test command Network operator Note: If is set to long alphanumeric (0) output of is according to the settings defined using the AT+CSCS command, i. e. either in GSM or in UCS2 character set.
AT command set for XX Siemens mobile phones and modems All outgoing barring services BAIC (bar all incoming calls) BAOC (bar all outgoing calls) BIC-Roam (bar incoming calls when roaming outside the home country) OI BOIC (bar outgoing international calls) OX BOIC-exHC (bar outgoing international calls except to home country) PS Phone locked to SIM (device code) P2 PIN2 SC SIM card (PIN) Password length AG AI AO IR Write command AT+CPWD=,, Response: OK/ERROR/+CME ERROR Par
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ +CREG: AT+CSSN AT+CSSN Supplementary service notifications Test command Response: Revision according to 3GPP TS 27.007 Version 5.0.
AT command set for XX Siemens mobile phones and modems 2.3.4 Commands related to mobile equipment control and status This section provides the descriptions of commands related to network service.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ OK/ERROR/+CME ERROR Parameter: see Read command String type; usually PIN2 AT+CBC AT+CBC Battery charge Test command Response: AT+CBC=? +CBC: (list of supported s),(list of supported s) OK/ERROR/+CME ERROR Parameter: 0 1 2 3 0 1-100 Execute command Response: AT+CBC +CBC: , ME is supplied from battery ME
AT command set for XX Siemens mobile phones and modems 20x,31x,33x,34x,51x,53x,54x)), ("GPRS coverage",(0,1)), ("callsetup",(0-3)) OK/ERROR/+CME ERROR Parameter: 0 .. 5 0 ..
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+CIND? +CIND: ,,...
AT command set for XX Siemens mobile phones and modems 2 0 0 MT can be operated from both MT keypad and TE only MT can write to its display only MT can set the status of its indicators Read command Response: AT+CMEC? +CMEC: ,0,0 OK/ERROR/+CME ERROR Parameter: See Test command Write command AT+CMEC=[[,0[,0]]] Response: OK/ERROR/+CME ERROR Parameter: See Test command AT+CMER AT+CMER Mobile Termination control mode Test command Response: AT+CMER=? +CME
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 0 1 ,. All indicator events shall be directed from TA to TE TA buffer of unsolicited result codes defined within this command is cleared when 1...3 is entered TA buffer of unsolicited result codes defined within this command is flushed to the TE when 1...
AT command set for XX Siemens mobile phones and modems Write command AT+CMUT= See Test command Response: OK/ERROR/+CME ERROR Parameter: Note: See Test command Only applicable during an active/hold call AT+CPAS AT+CPAS Query the telephone status Test command Response: AT+CPAS=? +CPAS: (list of supported s) OK/ERROR/+CME ERROR Parameter: 0 3 4 Ready Incoming call (phone is ringing) Call is active Execute command Response: AT+CPAS +CPAS: OK/ERROR/+CME ERROR Param
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+CPBR AT+CPBR Read a telephone-book entry Test command Response: AT+CPBR=? +CPBR: (list of supported s), , OK/ERROR/+CME ERROR Parameter: Location number Max. length of telephone number Max.
AT command set for XX Siemens mobile phones and modems See Test command integer type value indicating the number of used locations in selected memory integer type value indicating the total number of locations in selected memory Write command AT+CPBS=[,] Response: OK/ERROR/+CME ERROR Parameter: See Test command PIN2 only for selecting the FD-phonebook AT+CPBW AT+CPBW Write a telephone-book entry Test command Response: AT+CPBW=? +CPBW: (list of supp
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+CPIN=? OK Read command Response: AT+CPIN? +CPIN: OK/ERROR/+CME ERROR Parameter: READY SIM PIN SIM PUK PH-SIM PIN PH-SIM PUK SIM PIN2 SIM PUK2 No further input necessary SIM PIN input necessary SIM PUK input necessary Device code PIN (theft protection) input necessary Device code PUK (theft protection) input necessary PIN2, e.g.
AT command set for XX Siemens mobile phones and modems see AT+CSCS command price per unit; dot is used as a decimal separator (e.g. “1.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Test command Response: AT+CRSM=? OK Write command +CRSM=[,[,,,[,]]] Response: +CRSM: ,[,] OK/ERROR/+CME ERROR Parameter: , , , READ BINARY READ RECORD GET RESPONSE UPDATE BINARY UPDATE RECORD STATUS identifier of the data file on the SIM,
AT command set for XX Siemens mobile phones and modems AT+CTZR AT+CTZR Time Zone Reporting Test command Response: AT+CTZR=? +CTZR: (list of supported s) OK/ERROR/+CME ERROR Parameter: 0 1 Disable time zone change reporting Enable time zone change reporting Read command Response: AT+CTZR? +CTZR: OK/ERROR/+CME ERROR Write command Parameter: AT+CTZR= Unsolicited result code Parameter: +CTZV: See Test command Refer to AT+CCLK (e.g.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 2.3.5 Extensions of Hayes Standard commands for GPRS This chapter describes all the extensions of the Hayes Standard commands for GPRS.
AT command set for XX Siemens mobile phones and modems See Test command Write command AT+CGACT=[[,[,[,…]]]] Response: OK/ERROR/+CME ERROR Parameter: See Read command See Test command AT+CGANS AT+CGANS Manual response to a network request for PDP context activation Test command Response.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+CGAUTO AT+CGAUTO Auto response to a network request for PDP context activation Test command Response: AT+CGAUTO=? +CGAUTO: (list of supported s) OK/ERROR/+CME ERROR Parameter: indicates the state of PDP context activation 0 turn off automatic response for GPRS only 1 turn on automatic response for GPRS only 3 modem compatibility mode, GPRS and circ
AT command set for XX Siemens mobile phones and modems Write command AT+CGCMOD=[[,[,…]]]] Response OK/ERROR/+CME ERROR Parameter: See Test command AT+CGDATA AT+CGDATA Enter data state Test command Response: AT+CGDATA=? +CGDATA: (list of supported s) OK/ERROR/+CME ERROR Parameter: Layer 2 protocol to be used between the TE and MT PPP Point-to-Point Protocol Write command AT+CGDATA=[ ,[ [, [,…]]]] Response: CONNECT/ERROR/+CME ERROR Parameter: See Test co
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+CGDCONT? +CGDCONT: ,,,,, [ +CGDCONT: ,,,,, [...
AT command set for XX Siemens mobile phones and modems 2 3 RFC1144 (applicable for SNDCP only) RFC2507 Read command Response: AT+CGDSCONT? +CGDSCONT: , , , [+CGDSCONT: , , [...
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 1 streaming 2 interactive 3 background a numeric parameter that indicates the maximum number of kbits/s delivered to UMTS (up-link traffic) at a SAP. As an example a bitrate of 32kbit/s would be specified as '32' 0 network subscribed value 1..
AT command set for XX Siemens mobile phones and modems 0E0 network subscribed value 5E2-6E8 Range of supported values a numeric parameter that indicates whether SDUs detected as erroneous shall be delivered or not 0 No 1 Yes 2 no detect 3 network subscribed value a numeric parameter (0,1,2,…) that indicates the targeted time between request to transfer an SDU at one SAP to its delivery at the other SAP, in milliseconds 0 network subscribed value 1..
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+CGEQMIN=[ [, [, bitrate DL> [, [, [, [, bit error ratio> [, [, ]]]]]]]]]]]]] [, [, Response: OK/ERROR/+CME ERROR Parameter:
AT command set for XX Siemens mobile phones and modems 0 conversational 1 streaming 2 interactive 3 background 4 network subscribed value numeric parameter for the traffic class 1..8640 kbit/s a numeric parameter that indicates the maximum number of kbits/s delivered to UMTS (up-link traffic) at a SAP. As an example a bitrate of 32kbit/s would be specified as 32 1..8640 kbit/s Same as Maximum bitrate UL but for down link 1..
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ a numeric parameter that indicates whether SDUs detected as erroneous shall be delivered or not 0 No 1 Yes 2 no detect 3 network subscribed value a numeric parameter (0,1,2,…) that indicates the targeted time between request to transfer an SDU at one SAP to its delivery at the other SAP, in milliseconds 0 network subscribed value 1..
AT command set for XX Siemens mobile phones and modems AT+CGEQREQ=[ [, [, [, [, [, [, bit error ratio> [, [, ]]]]]]]]]]]]] UL> [, [, Response: OK/ERROR/+CME ERROR Parameter: <
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Write command AT+CGEREP=[[,]] Response OK/ERROR/+CME ERROR Parameter: See Test command See Test command Unsolicited result code: +CGEV: +CGEV: +CGEV: +CGEV: +CGEV: +CGEV: +CGEV: +CGEV: REJECT , NW REACT , NW DEACT , ME DEACT , NW DETACH ME DETACH NW CL
AT command set for XX Siemens mobile phones and modems AT+CGQMIN? +CGQMIN: ,,,,,[ +CGQMIN: ,,,,,[…]] OK/ERROR/+CME ERROR Parameter: numeric PDP Context Identifier See Test command See Test command See Test command See Test command See Test command See Test command Write command AT+CGQMIN=[[,[,[,[,
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ numeric parameter for the mean throughput class 0 network subscribed value 1..
AT command set for XX Siemens mobile phones and modems Write command AT+CGQREQ=[[,[,[,[,[,]]]]]] Response: OK/ERROR/+CME ERROR Parameter: See Read command See Test command See Test command See Test command See Test command See Test command AT+CGPADDR AT+CGPADDR Show PDP address Test command Response: AT+CGPADDR=? +CGPADDR: (list of defined s) OK/ERROR/+CME ERROR Parameter: numeric PDP Con
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Write command AT+CGREG=[] Response: OK/ERROR/+CME ERROR Parameter: Unsolicited result code +CGREG: See Test command AT+CGSMS AT+CGSMS Select service for MO SMS messages Test command Response: AT+CGSMS=? +CGSMS: (list of currently available s) OK/ERROR/+CME ERROR Parameter: numeric parameter for service or service preferen
AT command set for XX Siemens mobile phones and modems AT+CGTFT=? +CGTFT: list of supported s), (list of supported s), (list of supported s), (list of supported s), (list of supported s), (list of supported s), (list of supported s), (list of supported
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ (ipv6) and mask> Dot-separated numeric (0-255) parameters on the form 't.m'. 0..255 Hexadecimal parameter, value range from 00000 to FFFFF.
AT command set for XX Siemens mobile phones and modems See Test command See Test command See Test command See Test command 2.3.7 Commands related to mobile equipment errors AT+CMEE AT+CMEE Expanded error messages according to 3GPP TS 27.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Response: OK/ERROR Parameter: See Test command AT+VTS AT+VTS Send a DTMF tone Test command Response: AT+VTS=? (list of supported s), (list of supported s) OK/ERROR/+CME ERROR Parameter: 0-9, exactly one character of the list #,*, A-D 1 ..
AT command set for XX Siemens mobile phones and modems AT+CMGD AT+CMGD Delete an SMS in the SMS memory Test command Response: At+CMGD=? OK/ERROR/+CME ERROR Write command AT+CMGD= Response: OK/ERROR/+CMS ERROR Parameter: Index of message in the selected memory AT+CMGF AT+CMGF SMS format Test command Response: AT+CMGF=? +CMGF: (list of supported s) Parameter: Read command AT+CMGF? 0 PDU mode Response: +CMGF: Parameter: See Test command
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ ,,[],[...]] Parameter: Index of message in selected memory See Test command The PDU begins with the service-center address (according to GSM 04.11, [9]), followed by the TPDU (according to GSM 03.
AT command set for XX Siemens mobile phones and modems +CMGS: If sending is not successful: +CMS ERROR Parameter: Length of PDU The PDU begins with the service-center address (according to GSM 04.11, [9]), followed by the TPDU (according to GSM 03.40, [6]) in hexadecimal format Message reference RP-ACK PDU according to GSM 03.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ command response and next send command exceeds 5 seconds then ME closes the link and TA does NOT switch to 0 Read command AT+CMMS? Response: +CMMS: Parameter: See Test Command Write command AT+CMMS=[] Response: OK/ERROR Parameter See Test Command AT+CMSS AT+CMSS Send an SMS from the SMS memory Test command Response AT+C
AT command set for XX Siemens mobile phones and modems Notes TA selects the procedure how the receipt of new messages from the network is indicated to the TE when TE is active, e.g. DTR signal is ON. If TE is inactive (e.g. DTR signal is OFF), message receiving should be done as specified in GSM 03.38 ( see [5]). 1) If the DTR signal is not available or the state of the signal is ignored (V.250 command &D0), reliable message transfer can be assured by using AT+CNMA acknowledgement procedure.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ unsolicited result code: +CDS: (PDU mode enabled) 2 If SMS-STATUS-REPORT is routed into ME/TA, indication of the memory location is routed to the TE using unsolicited result code: +CDSI: , 1 TA buffer of unsolicited result codes defined within this command is cleared when 1...3 is entered.
AT command set for XX Siemens mobile phones and modems MT combination of "ME" and "SM" storages Memory in which received messages are preferred to be stored, if routing to TE is not set (see AT+CNMI command with parameter =2) SM SIM message storage ME Mobile Equipment message storage MT combination of "ME" and "SM" storages Read command Response: AT+CPMS? +CPMS: ,,,,,,,
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+CSCB? +CSCB: ,, Parameter: See Test command String type; combinations of CBM message IDs String type; combinations of CBM data coding schemes Write command AT+CSCB=[[,[,]]] Parameter: See Test command String type; combinations of CBM message IDs String type; combinations of CBM
AT command set for XX Siemens mobile phones and modems AT+CBST =? +CBST: (list of supported s), (list of supported s), (list of supported s) OK Parameter: 0 4 6 7 14 68 70 71 75 0 1 auto bauding 2400 bps ( V.22bis) 4800 bps ( V.32) 9600 bps (V.32) 14400 bps (V.34) 2400 bps (V.110) 4800 bps (V.110) 9600 bps (V.110) 14400 bps (V.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ See Test command See Test command See Test command See Test command Write command AT+CRLP= [[,[,,]]] Response: OK/ERROR/+CME ERROR Parameter: See Test command See Test command See Test command See Test command 2.6 Fax commands The following commands can be used for FAX transmission.
AT command set for XX Siemens mobile phones and modems Used for FAX class 2 only This command defines the “Copy Quality OK” threshold. If pixel count errors were detected in normal resolution (98 dpi) mode in as many consecutive lines as defined in , the copy quality is unacceptable. If pixel count errors were detected in fine resolution (196 dpi) mode in twice as many consecutive lines as defined in , the copy quality is unacceptable.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+FBOR? OK/ERROR/+CME ERROR Parameter: OK Write command AT+FBOR= Response: OK/ERROR Parameter: OK AT+FCIG AT+FCIG Query or set the Local polling id Used for FAX class 2 only Test command Response: AT+FCIG=? +FCIG: (max.
AT command set for XX Siemens mobile phones and modems AT+FCQ= See Test command AT+FCLASS AT+FCLASS Select, read or test FAX service class Test command Response: AT+FCLASS=? +FCLASS: (list of supported s) OK/ERROR/+CME ERROR Parameter: 0 1 2 Read command AT+FCLASS? data (e.g. EIA/TIA-602 or ITU V.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ st Note: Read command: Response: AT+FDCC? OK Scan Time / line For further information see AT+FDIS Parameter: vr br wd ln df ec bf st See Test command See Test command See Test command See Test command See Test command See Test command See Test command See Test command Write command AT+FDCC=,
,,,,,, Response: +FDCC: (li
AT command set for XX Siemens mobile phones and modems See Test Command AT+FDIS AT+FDIS Query or set session parameters Used for FAX class 2 only This command allows the controlling application to set and constrain the capabilities used for the current session. +FDIS is used to generate DIS or DTC messages directly. +FDIS (and received DIS messages) is also used to generate DCS messages.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 6 7 40 ms 40 ms _________________________________________________________________________________________ Document No.: Revision: Revision Date: A30880-A10-A001-XXD376 Master R75 29.
AT command set for XX Siemens mobile phones and modems *) Note: Only the default value needs to be implemented.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Vertical Resolution 0 normal, 98 lpi 1 fine, 196 lpi wd Page Width * 1728 pixels in 215mm 0) 1 2048 pixels in 255 mm 2 2432 pixels in 303 mm 3 1216 pixels in 151 mm 4 864 pixels in 107 mm ln Page length 0 A4, 297mm 1 B4, 364mm 2 unlimited length Only the default value needs to be implemented.
AT command set for XX Siemens mobile phones and modems Parameter: Local ID string, max. length and possible content as reported by test command. Default value is empty string (“”). Maximum length: 20 See also the “AT+FCIG” command Read command AT+FLID? Response: OK Parameter: See Test Command Write command Response AT+FLID= +FLID: (max.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+FOPT AT+FOPT Set bit order independently Used for FAX class 2 only Read command Parameter: AT+FOPT? 0 1 non-standard standard Write command AT+FOPT= Model-specific command to set bit order independently of the understanding which is "mirrored" and which is direct.
AT command set for XX Siemens mobile phones and modems Used for FAX class 1 only This command causes the TA to receive frames using the HDLC protocol and the modulation defined below. An ERROR response code results if this command is issued while the modem is onhook.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+FTH? Write command AT+FTH= Parameter: 3 V.21 Ch2 300 bps This command causes the TA to transmit data using HDLC protocol and the modulation mode defined below. An ERROR response code results if this command is issued while the modem is on-hook.
AT command set for XX Siemens mobile phones and modems AT+FVRFC=? This command determines the DCE response to a mismatch between the vertical resolution negotiated for the facsimile session and the Phase C data desired by the DTE.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+BRSF AT+BRSF Report Supported Features Test command Response: AT+BRSF=? OK/ERROR/+CME ERROR Write command AT+BRSF= Response: +BRSF: OK Parameter: A 32 bit integer type parameter: Bit Feature o Three-way Calling 1 EC and/or NR function 2 Voice Recognition 3 In-band ringing Tone (AT+BSIR) 4 Attach a number to a voice Tag (AT+BINP) 5 Abi
AT command set for XX Siemens mobile phones and modems AT+GCAP AT+GCAP Request Capabilities List Test command Response: AT+GCAP=? OK/ERROR Read command Response: AT+GCAP? +GCAP: Parameter : e.g. “+GCAP: AT+CGSMS , AT+FCLASS” AT+IPR AT+IPR Fixed DTE rate Test command Response: AT+IPR=? +IPR: (list of supported values) OK/ERROR/+CME ERROR Parameter: bits per second at which the DTE-DCE interface is to operate.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ integer type parameter, indicating the status of the Accessory Data interface 0 disable Notifications and Accessory Data Transfer 1 enable Accessory Data Transfer Mode 2 Data Transfer mode Note: It can be used directly since x65 devices, no need to switch in mode 1 beforehand.
AT command set for XX Siemens mobile phones and modems Note: Unsolicited Result Code, only available if Data Transfer Mode enabled (i. e.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT^SBLK=? OK/ERROR/+CME ERROR Execute command Response: AT^SBLK OK/ERROR/+CME ERROR AT^SBMH AT^SBMH Bookmark Handling Test command Response: AT^SBMH=? ^SBMH: (list of supported s),max.
AT command set for XX Siemens mobile phones and modems 0 first (and only) entry of type vcs 1 entry of type vcs vcf vcard format specification: http://www.imc.org/pdi 0 first (and only) entry of type vcf 1 entry of type vcf t9d Tegic database for t9 text recognition.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 0 first (and only) entry of type t9d deletes entry of the current subtype current packet number maximum number of packets 0 other Write command AT^SBNW=,, [[, ]] PDU is given: Response: OK/ERROR/+CME ERROR Parameter: Notes: Restriction see Test command s
AT command set for XX Siemens mobile phones and modems 1 supported 0 HighSpeedSim; (1) not active 1 active 000 Accessory; (3) no Accessory 001 DataCable 010 Bluetooth 011 ..
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 11 Reserve Battery; (4) 11 + 1 States ChargeCount (16) 4 special quantisation coding ChargeBroken; (16) 3 special quantisation coding ChargeFast; (16) 3 special quantisation coding Diagnosis (Lifetime 5 * 3 Bit = 15 Bit ), specified as a 4-digithexadecimal-value Turnoffs Exits Restarts OpTime TalkTime AT^SCID AT^SCID Output card ID Test command Re
AT command set for XX Siemens mobile phones and modems AT^SCKS= OK/ERROR Parameter See Test command Unsolicited result code ^SCKS: AT^SCNI AT^SCNI Output call number information Test command Response: AT^SCNI=? OK/ERROR/+CME ERROR Execute command Response: AT^SCNI ^SCNI: ^SCNI: ^SCNI: ^SCNI: ^SCNI: ^SCNI: ^SCNI: 1[,[,,]] 2[,[,,]] 3[,[,,]] 4[,[,,]] 5[,[,,]]
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Note: In the field, special characters like the following may appear: `"` (0x22), `@` (0x00), `ò` (0x08), `Ö` (0x5c). (See also AT+CPBW and Appendix A: “How to use special characters in certain commands ( e. g.
AT command set for XX Siemens mobile phones and modems AT^SGDCONT=? ^SGDCONT: (range of supported s), ,,,(list of supported s), (list of supported s) [ ^SGDCONT: (range of supported s), ,,,(list of supported s),(list of supported s)[...]] OK/ERROR/+CME ERROR Parameter: numeric PDP Context Identifier 0 ..
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ The context ID count of bytes of downlink count of bytes of uplink Write command Response AT^SGDV= OK/ERROR/+CME ERROR Parameter: See Test command AT^SICO AT^SICO Icon control Test command Response: AT^SICO =? ^SICO: (list of supported s),( list of supported s) OK/ERROR/+CME ERROR Write command AT^SICO =, Response
AT command set for XX Siemens mobile phones and modems AT^SKPD = OK/ERROR/+CME ERROR Parameter: The key in ASCII integer format (e.g.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ dedicated PAD access combination of some of the above classes, e.g. 255 regroups all classes and 5 regroups Voice and FAX Off On 128 X 0 1 AT^SLNG AT^SLNG Language settings Test command Response: AT^SLNG=? ^SLNG: (list of supported languages s) Parameter: Integer; language coded according to GSM 03.
AT command set for XX Siemens mobile phones and modems AT^SMGO AT^SMGO SMS overflow indicator Test command Response: AT^SMGO=? ^SMGO: (list of supported s) OK/ERROR/+CMS ERROR Parameter: 0 1 Disable Enable Read command Response: AT^SMGO? ^SMGO: , OK/ERROR/+CMS ERROR Parameter: See Test command 0 Space still available 1 SMS storage full (The "SM" and "ME" storages are full, i. e. the "MT" storage is full. See AT+CPMS command.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 3 STO SENT stored sent messages 4 ALL all messages See the AT+CMGL command otherwise: +CMS ERROR: Index of message in selected memory AT^SMSO AT^SMSO Switch device off Test command Response: AT^SMSO=? OK/ERROR/+CME ERROR Execute command Parameter: AT^SMSO OK Device switches off Write command AT^SMSO= Parameter:
AT command set for XX Siemens mobile phones and modems 1 2 3 4 Read command AT^SNFV? max. volume (approx. 3 dB/level) Response: ^SNFV: Parameter: See Test command Write command AT^SNFV= Response OK/ERROR Parameter See Test command AT^SOBX AT^SOBX Set OBEX Debug Level Write command AT^SOBX= Response: OK/ERROR/+CME ERROR Parameter: 0 .. 127 enables a specific level of tracing for OBEX debug information.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT^SPBC= Response: ^SPBC: OK/ERROR/+CME ERROR Parameter: First letter of desired entry Value range: capital letters only (if is not capital letter, the index of the first entry beginning with a special character is displayed) Index in the sorted telephone book (access via AT^SPBG) A ..
AT command set for XX Siemens mobile phones and modems Last number redial memory in telephone device Telephone book in device Missed dialing numbers (unanswered calls) Own telephone numbers Own numbers ME Received Calls List Red book (all entries in ”CS” whose name portions have an exclamation mark (‘!’) as their final character) SD Service dialing numbers For detailed information on the telephone-book features see “ Appendix A” MD ME MS ON OW RC RD Read command Response: AT^SPBS? ^SPBS: [,,<
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT^SPLM AT^SPLM Read the PLMN list Test command Response: AT^SPLM=? OK/ERROR/+CME ERROR Execute command: Response: AT^SPLM ^SPLM: numeric ,long alphanumeric [ ^SPLM: numeric ,long alphanumeric […]] OK/ERROR/+CME ERROR Parameter Network operator in numeric and alphanumeric notation AT^SPLR AT^SPLR Read an entry fro
AT command set for XX Siemens mobile phones and modems AT^SPST =? ^SPST: (list of supported s) OK/ERROR/+CME ERROR Write command AT^SPST =, Response: OK/ERROR/+CME ERROR Parame ter: Type of Signal Tone (st = self terminating) 0 Carkit PTT (st) 1 Carkit PTT long (st) 2 Carkit Crash (st) 3 Carkit Error (st) 4 Carkit Call Setup (st) Mode 0 Stop tone (not necessary for self terminating tones) 1 Play tone AT^SPTT AT^SPTT Push To Talk (for BT Headset) Test command Response: AT^SPTT =?
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ PP Service provider personalization (GSM 02.
AT command set for XX Siemens mobile phones and modems The Write command starts playing the ring melody. Execute command Response: AT^SRMP OK/ERROR/+CME ERROR The Execute command stops the melody played. If an MTC is received during an active test ring, the test ring is switched off and the ”normal” ring is switched on.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Example Note: Delete Action If no parameters are provided, every setting will be deleted. If no parameter is entered then all settings of this application are deleted Otherwise just the setting corresponding to the key will be deleted. Set Action All parameters are mandatory.
AT command set for XX Siemens mobile phones and modems Parameter: integer type value; the following values are defined: 0 stop recording and save the Voice Memo, or stop playback of Voice Memo 1 cancel recording without saving current file 2 start recording; no index is needed - if an index is specified, an error is issued. If a name is specified, it will be associated with the current Voice Memo; otherwise, is used as name. gives the max.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ string of format yy-MM-dd,hh:mm:ss[±zz] indicating year, month, day, hour, minutes, seconds and, optionally, time zone (indicates the difference between the local time and GMT, expressed in quarters of an hour, range 47...+48) E.g.
AT command set for XX Siemens mobile phones and modems AT^STRC AT^STRC Activate Universal Data Tracer Test command Response: AT^STRC=? OK/ERROR/+CME ERROR Write command AT^STRC= [,] Response: OK/ERROR Parameter: enables a specific level of tracing e.g. RLP, PPP. 0 tracer disabled 1 2 3 4 5 6 7 specifies the serial interface which should be used for debug output. 0 1 This command can only be used if the RESI-SAP is activated in the mobile device. 2.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+CGEREP The mobile equipment has forced a context deactivation For an explanation of parameters see AT+CGEREP The mobile equipment has forced a GPRS detach For an explanation of parameters see AT+CGEREP The network has forced a change of MS class For an explanation of parameters see AT+CGEREP The network has forced context deactivation For an explanation of param
AT command set for XX Siemens mobile phones and modems +CSSU: [,[][,]] +CTZV: ^SABD: ^SACD: ^SACM: ^SCBI: , ^SCBI: ,,, ^SCKS: ^SMGO: ^SSTK: +VGS: ^SVMC: intermediate/unsolicited result code For an explanation of parameters see AT+CSSN Time Zone Changed indication For an explanation of parameters see AT+CTZR For an explanation of parameters see AT^SABD For an explanation of parameters see AT^SACD
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 3 Appendix A 3.1.1 Factory settings made by AT&F Reset pending locks (Phone Pin/Puk, Pin2/Puk2 ...
AT command set for XX Siemens mobile phones and modems AT^SABD=0 Only for Master Document: AT^SACD=0 AT^SADT=0 3.1.2 Features of the Telephone book memory Table 3-1 lists the features supported by the telephone book memory. Name FD SM DC (MD) ON (OW) LD ME BD Description Category Access Write allowed ? Fix-dialing number (SIM fix-dialing telephone book) Abbreviate dialing number (SIM telephone book) 3GPP TS 27.007 3GPP TS 27.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ RD FD) Red book numbers (CS entries with ! at the end of the name portion) Siemens AT^SPBG AT^SPBS, AT^SPBC, AT^SPBG - Table 3-1: Features of the telephone book memory 3.1.3 Writing to the FDN Phonebook / FDN Replacement Writing to the fixed-dialing number phonebook is protected by PIN2. A sample Write sequence (to e.g.
AT command set for XX Siemens mobile phones and modems In addition, if there is no FDN phonebook available on the SIM, it is possible to activate a feature which activates an FDN-like behavior for the ”SM” and ”ME” phonebooks (FDN replacement). (Currently this feature can only be activated via the MMI lock/device lock/excluding telephone book.) In this case, the Write to the ”SM” and ”ME” phonebooks is ensured by the device code (PH-SIM PIN and PHSIM PUK, respectively).
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ Table 3-3: Using escape characters in GSM commands Note: When reading phonebook records, there is NO replacement. Every character will appear in normal GSM character set notation (like the left column in the example above). 3.
AT command set for XX Siemens mobile phones and modems TxD RxD CTS DCD DTE to DCE DCE to DTE DCE to DTE DCE to DTE Transmitted Data Received Data Clear To Send Data Carrier Detect 103 104 106 109 __________________________________________________________________________________________ Document No.: Revision: Revision Date: 127 A30880-A10-A001-XXD376 Master R75 29. September.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 4 Appendix B 4.1 Example for creating / retrieving an organizer entry -vcs object which has to be uploaded: BEGIN:VCALENDAR VERSION:1.0 BEGIN:VEVENT CATEGORIES:ANNIVERSARY DTSTART:19991213T100000 DESCRIPTION:W.
AT command set for XX Siemens mobile phones and modems -interrogation of the current ,,, at^sbnw? ^SBNW: "vcs",20,2,3 OK description: The current object which is uploaded is an VCS object. It has to be stored on record 20. 2 of 3 packets have already been uploaded.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ The present version of the mobile software supports CID 1, CID 2 and CID 3 by using the AT+CGDCONT and the AT+CGDSCONT command. All three CIDs could be defined as a primary or a secondary context. Furthermore the CIDs are global within the mobile.
AT command set for XX Siemens mobile phones and modems • the reliability class • the peak throughput class • the mean throughput class and is subdivided into "requested QoS" and "minimum acceptable QoS". All parameters of the QoS are initiated by default to the "network subscribed value (= 0)", but the QoS itself is set to undefined. Use the AT+CGQREQ or AT+CGQMIN command to define a QoS. e.g.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ If no CID is defined the mobile returns +CME ERROR: invalid index Remark: If the mobile is NOT attached via AT+CGATT=1 before activating, the attach is automatically done by means of the AT+CGACT command.
AT command set for XX Siemens mobile phones and modems CONNECT // establish a connection via service code 99, IP address 123… //and L2P = PPP and using CID 1.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ ^SVMC: OK Meaning: The recording of a voice memo has been stopped, saving the file, or the playing of the voice memo has been stopped. No error occurred.
AT command set for XX Siemens mobile phones and modems Meaning: The voice memo stored with the index 2 is to be deleted. Read command The Read command indicates whether a playback or recording is running (type), the remaining time (recording time or playback time) and the name (if available) of the current Voice Memo. Sample input and resulting output: AT^SVMC? ^SVMC: 0 Meaning: Currently no action is performed for a voice memo, the value of is “Idle”.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 5 Errors and Messages This section provides information on the final result code of a command execution (+CMS ERROR: ) and indicates an error related to mobile equipment or network. 5.1 Summary of CME ERRORS (+CME ERROR) related to 3GPP TS 27.007 Table 5-1 lists the numbers and meaning of CME errors (+CMS ERROR: ) related to 3GPP TS 27.007 [15].
AT command set for XX Siemens mobile phones and modems 106 107 111 112 113 132 133 134 148 149 150 Illegal MS (#3) (Values in parentheses are GSM 04.08 cause codes, see [8].
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 129 130 143 144 145 159 160 161 175 176 192 193 194 195 196 197 198 199 208 209 210 211 212 213 255 300 301 302 303 304 305 310 311 312 313 314 315 316 317 318 320 321 322 330 331 332 340 500 512 Short message Type 0 not supported Cannot replace short message Unspecified TP-PID error Data coding scheme (alphabet) not supported Message class not supported Unspecifi
AT command set for XX Siemens mobile phones and modems 5.3 GSM return values issued by AT+CEER Table 5-7 lists the GSM return values issued by the AT+CEER command in the form ,, where x indicates the type of the value returned and y denotes the reason why the call was terminated. Table 5-7 provides the values for the applications handled by AT+CEER (x values).
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ NO SUITABLE CELLS in this LA NETWORK FAILURE MAC FAILURE (sent to network) SYNCH FAILURE (sent to network) CONGESTION GSM auth. Unaccept. (sent to network, UMTS only) SERVICE OPT. NOT SUPPORTED REQ. SERVICE NOT SUBSCRIBED SERV. TEMPOR.
AT command set for XX Siemens mobile phones and modems ONLY RESTRICTED DIGITAL INFORMATION BEARER CAP. AVAIL. SERVICE OR OPTION NOT IMPL. INVALID TI USER NOT MEMBER OF CUG INCOMPATIBLE DESTINATION INVALID TRANSIT NETWORK SELECTION SEMANTICALLY INCORRECT MESSAGE INVALID MANDATORY INFORMATION MESSAGE TYPE NOT IMPLEMENTED MESSAGE NOT COMP W. CC STATE IE NOT IMPLMENTED CONDITIONAL IE ERROR MESSAGE NOT COMP W.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 17 22 48 – 63 95 96 97 98 99 100 101 111 Network failure Congestion Retry upon entry into new cell low – high Message semantically incorrect Mandatory information invalid Message type does not exist or is not implemented Message type incompatible with protocol state Information element does not exist or is not implemented Conditional error Message incompatible wit
AT command set for XX Siemens mobile phones and modems 6 7 DeactActStaticPDPaddressCollision Unspecified protocol error Table 5-10: Internal values of Session Manager issued by AT+CEER 5.4.4 Value 0 1 2 3 4 255 Internal values GAPI issued by AT+CEER Meaning Regular deactivation of the call Action temporarily not allowed Wrong connection type Specified data service profile invalid PDP type or address is unknown Undefined Table 5-11: GAPI values issued by AT+CEER 5.4.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ 5.5 List of keys implemented for AT+CKPD / AT^SKPD The following keys are implemented for the AT+CKPD and AT^SKPD commands: key value (dec) (AT^SKPD) 35 37 42 48 .. 57 Character (AT+CKPD) # % * 0..
AT command set for XX Siemens mobile phones and modems “:” following the CKPD command indicates the use of manufacturer specific keys. The subsequent X states a that a string may be appended, which can include all Siemens keys in hexadecimal format. Otherwise an error will be indicated. A command could look like.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ BUSY 7 Remote station busy CONNECT 2400 10 Link with 2400 bps CONNECT 4800 30 Link with 4800 bps CONNECT 9600 32 Link with 9600 bps CONNECT 14400 33 Link with 14400 bps CONNECT 2400/RLP 47 Link with 2400 bps and Radio Link Protocol CONNECT 4800/RLP 48 Link with 4800 bps and Radio Link Protocol CONNECT 9600/RLP 49 Link with 9600 bps and Radio
AT command set for XX Siemens mobile phones and modems #333*Pw*BS# #353*Pw*BS# Deact. All Outg.Barring Services Deactivation. All Inc.Barring Services Table 5-15: List of *# codes __________________________________________________________________________________________ Document No.: Revision: Revision Date: 147 A30880-A10-A001-XXD376 Master R75 29. September.
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ The abbreviations used in Table 5-15 have the following meaning: ZZ ZZ DN BS type of supplementary services dialling number basic service:Voice T Pw time in seconds network password 330 ---0-9 11 16 13 12 19 10 25 24 27 26 21 22 20 ---- Barring services All services string of digits Voice Sms Fax Sms+fax Voice+fax Voice+SMS+fax Data circuit asyncron Data circu
AT command set for XX Siemens mobile phones and modems 6 Index AT 13 AT&C ............................................................................ 14 AT&D ............................................................................ 14 AT&F ............................................................................ 15 AT&\N........................................................................... 15 AT&\Q........................................................................... 15 AT^S KPD...........
AT command set for XX Siemens mobile phones and modems _________________________________________________________________________________________ AT+CLVL ..................................................................... 38 AT+CMEC.................................................................... 38 AT+CMEE.................................................................... 67 AT+CMER.................................................................... 39 AT+CMGC .........................................
