Specifications

3GPP
3GPP TS 27.007 V6.3.0 (2003-
06)
14
7
Release 6
Annex A (normative):
Summary of commands from other standards
Summary of ITU-T Recommendation V.250 [14] commands applicable to GSM/UMTS:
Table A.1: V.250 commands applicable to GSM/UMTS
Name
V.250
subclause
Description
Subclauses in the
present document
&C
6.2.8
Circuit 109 (Received line signal detector) Behaviour
4.3
&D
6.2.9
Circuit 108 (Data terminal ready) Behaviour
4.3
&F
6.1.2
Set to Factory-defined Configuration
5.8/ 3
+DR
6.6.2
Data Compression Reporting
6.20
+DS
6.6.1
Data Compression
6.20
+GCAP
6.1.9
Request Complete Capabilities List
5.8
+GCI
6.1.10
Country of Installation
5.8
+GMI
6.14
Request Manufacturer Identification
5.8/ 5.1
+GMM
6.1.5
Request Model Identification
5.8/ 5.2
+GMR
6.1.6
Request Revision Identification
5.8/ 5.3
+GOI
6.1.8
Request Global Object Identification
5.8
+GSN
6.1.7
Request Product Serial Number Identification
5.8/ 5.4
+ICF
6.2.11
DTE-DCE Character Framing
4.3
+IFC
6.2.12
DTE-DCE Local Flow Control
4.3
+ILRR
6.2.13
DTE-DCE Local Rate Reporting
4.3
+IPR
6.2.10
Fixed DTE Rate
4.3
A
6.3.5
Answer
6.19/ 6.6
D
6.3.1
Dial
6.1-6.4/ 6.6
E
6.2.4
Command Echo
4.3
H
6.3.6
Hook Control
6.19/ 6.5/ 6.6
I
6.1.3
Request Identification Information
5.8
L
6.3.13
Monitor Speaker Loudness
6.19
M
6.3.14
Monitor Speaker Mode
6.19
O
6.3.7
Return to Online Data State
6.19
P
6.3.3
Select Pulse Dialling
6.19
Q
6.2.5
Result Code Suppression
4.3
S0
6.3.8
Automatic Answer
6.19
S10
6.3.12
Automatic Disconnect Delay
6.19
S3
6.2.1
Command Line Termination Character
4.3
S4
6.2.2
Response Formatting Character
4.3
S5
6.2.3
Command Line Editing Character
4.3
S6
6.3.9
Pause Before Blind Dialling
6.19
S7
6.3.10
Connection Completion Timeout
6.19
S8
6.3.11
Comma Dial Modifier Time
6.19
T
6.3.2
Select Tone Dialling
6.19
V
6.2.6
DCE Response Format
4.3/ 3/ 4.1/ 4.2
X
6.2.7
Result Code Selection and Call Progress Monitoring Control
4.3
Z
6.1.1
Reset To Default Configuration
5.8
The use of ITU-T Recommendation V.42 error control protocol is not specified for GSM/UMTS, but if a manufacturer
chooses to implement it over transparent data service, +E prefixed commands of V.250 [14] shall be used.
ITU-T T.31 [11] and T.32 [12] may be used as facsimile TA-TE protocols without deletions or additions to the
command set.
TIA IS-99 [15] commands referenced in the present document: