Owner`s manual

Mixer Controls
CM Labs MotorMate Owner’s Manual Page 15
Channel In/Out Assignment
Press and hold SHIFT (on the MotorMate lower panel)
and then press “assign” on the MotorMate lower panel.
The “assign” LED will flash to show that assignment is in
process. During assignment, the Burn Mode Switches
and the Rotary Mode Switches are all disabled.
The Rotary Display will show “In” for input assignment. If
you push the View Stick up, the Rotary Display will show
“Ou” for Output assignment. Push the View Stick down,
and the Rotary Display will go back to “In” for input
assignment.
Any SELECT LED’s that were on, now go off, and the top
row of the LCD will display the input or output assign-
ments for each channel in the current 8 channel view.
Rotate the rotary pots to move through the list of assign-
ment choices. The choices will appear on the LCD top
row as you do this. The bottom row of the LCD will show
where the current selection is in the list of choices.
When the SELECT LED flashes, it indicates that the
choice in that channel input or output assignment is not
the original one. When any channel SELECT is flashing,
you can not switch from “In” to “Ou” or “Ou” to “In” with
the Rotary Selector.
When the desired assignment is shown on the LCD,
press that channel’s SELECT switch. That will lock in that
assignment on that channel. The channel SELECT will
light solid to indicate it is locked in.
At this point you can continue to make similar changes in
the other 7 channels in this current view, or press the
Right or Left Arrow Switches or use the View Stick to
move to another view. When you are done assigning
inputs or outputs, you can press the SEND, or PLUG-IN
Rotary Mode switches to make assignments there. If you
are done assigning altogether, either press the “assign”,
ESC, or the SHIFT switch on the MotorMate lower
panel. The “assign” and SHIFT LED’s will go out.
Defaulting Sends to Unity
To quickly set a channel send to unity, press and hold
down the DEFAULT switch (third switch up to the left of
the faders) and press any of the MULTI switches below
the rotaries.
To quickly set all channel sends to unity, press and hold
down the ALL switch (fourth switch up to the left of the
faders), press and hold down the DEFAULT switch
and then press any of the MULTI switches below the
rotaries.
Send Buss Assignment
Press and hold SHIFT on MotorMate and then press
“assign” on the MotorMate lower panel. The “assign” LED
will flash to show that assignment is in process. During
assignment, the Burn Mode Switches and the Rotary
Mode Switches are all disabled.
The Rotary Display will continue to show “Sx” for the
current Send. Push the View Stick up or down to select
any of the Sends for assignment.
Any SELECT LED’s that were on, now go off, and the top
row of the LCD will display the input or output assign-
ments for each channel in the current 8 channel view.
Rotate the rotary pots to move through the list of assign-
ment choices. The choices will appear on the LCD top
row as you do this. The bottom row of the LCD will show
where the current selection is in the list of choices.
When the SELECT LED flashes, it indicates that the
choice in that channel input or output assignment is not
the original one. When any channel SELECT is flashing,
you cannot switch from one Send to another with the
Rotary Selector.
When the desired assignment is shown on the LCD,
press that channel’s SELECT switch. That will lock in that
assignment on that channel. The channel SELECT will
light solid to indicate it is locked in.
At this point you can continue to make similar changes in
the other 7 channels in this current view, or press the
Right or Left Arrow Switches or use the View Stick to
move to another view. When you are done assigning
Sends, you can press the MIX or PLUG-IN Rotary Mode
switches to make assignments there.
If you are done assigning altogether, either press the
“assign”, ESC, or the SHIFT switch on the MotorMate
lower panel. The “assign” and SHIFT LED’s will go out.