Contents INSTRUCTION MANUAL Stand-Alone 16 Channel DIGITAL VIDEO RECORDER MODEL CDR1650 Ver. 041308, 042909,102609 Copyright © 2008 Clover Electronics U.S.A. All Rights Reserved.
Contents CONTENTS ABOUT THIS MANUAL....................................................................................................................... 9 1. UNPACKING.................................................................................................................................. 11 STAND-ALONE DVR (DIGITAL VIDEO RECORDER) UNIT ................................................................. 12 2.FEATURES .................................................................................
Stand-alone DVR Instruction Manual 6-6.2. SPLIT SCREENS...........................................................................................................................40 6-7. LIVE ................................................................................................................................. 41 6-7.1. FULL SCREEN...............................................................................................................................41 6-7.2. SPLIT SCREEN ...................
Contents 7-2.1. TIME / DATE ..................................................................................................................................78 7-2.2. SYSTEM CONFIG .........................................................................................................................80 7-2.2.1. FACTORY DEFAULT ..............................................................................................................80 7-2.2.2. LOAD CONFIG / BACKUP CONFIG ...............................
Stand-alone DVR Instruction Manual 7-6.8.3. Timer Recording (Schedule Recording) ...............................................................................104 7-6.8.4. Timer Event Recording .........................................................................................................104 7-6.9. Recording by Motion Detection....................................................................................................105 7-6.10. Recording by Sensor (PIR Sensor) ...........................
Contents 8-4.9.1. Terminal mode.......................................................................................................................150 8-4.9.2. Multi mode.............................................................................................................................151 8-4.10. Copy in the Terminal mode ........................................................................................................152 8-4.11 E-Map .......................................................
Stand-alone DVR Instruction Manual 8
About this manual This is the Instruction Manual for Stand-alone type DVR model CDR1650. This Manual describes how to install and operate the Stand-Alone DVR and provides specifications and features. Please read this manual thoroughly and follow the installation process before using Standalone DVR (Note: Be sure to correctly follow step 3. What to do at the time of installation). Contact our dealers when you have any queries.
Stand-alone DVR Instruction Manual 10
1 1. Unpacking Care should be taken when unpacking to avoid damaging the unit. Please check that the following items are included: ▶ Stand-alone DVR unit ▶ All Accessories : Bracket, Power Cable, Screws ▶ Remote Controller & Battery ▶ PS2 Mouse ▶ DSUB 26p Connector (Sensor Input, Relay Output Selection) ▶ Instruction Manual ▶ Host Program (DVR Master) on CD ▶ RJ-45 Cable Note: Contact your dealer immediately if any components are missing.
Stand-alone DVR Instruction Manual Stand-alone DVR (Digital Video Recorder) Unit CDR1650 is the most reliable and functional embedded DVR system available today. The system displays 16 channels of live images in Real Time speed, compresses data digitally and records them to the Hard Disk Drive, which can be replayed and searched easily any time. The CDR1650 supports easy back up via USB port, DVD R/W, CD R/W and networking in both static & dynamic IP modes.
2 2.Features ▶ Multi Functional Record - Powerful, multiple Record Modes available: Manual (Continuous), Timer, and Motion Detection Recording. ▶ User friendly GUI - A few simple buttons for Easy control. ▶ Automatic System Recovery - Automatic and Complete System recovery within 10 seconds.
Stand-alone DVR Instruction Manual 14
3 3.What to do at the time of Installation Stand-alone DVR should be installed in the following order; 1. Make sure all the required hardware is available. - Stand-alone DVR unit (including HDD) - Up to 16 cameras (including power source) - CCTV or VGA monitor (or TV set) - Network cable if connecting to a PC 2. Connect the cameras, the DVR unit and monitor (Refer to [Fig 5-3]). 4. Confirm live video is displayed on the monitor before going to the next step. 5.
Stand-alone DVR Instruction Manual 16
4 4.Specifications D ESC RIPTIO NS ITEM VIDEO SIG NAL Television System Refresh Rate NTSC 60 fields/sec Video Resolution 720x480 720x576 16 Cameras Composite 1.0 Vp-p 75 O hms Video Inputs Video Input Signal 16 looping, Main monitor, Aux monitor, VG A Video O utputs Composite 1.
Stand-alone DVR Instruction Manual 18
5. Installation 5 5. Installation CONTENTS 5-1. CONTROLS AND CONNECTORS (FOR 8CH & 16CH DVR)........................................................20 5-2. NOTE FOR INSTALLATION ......................................................................................................22 5-3. SYSTEM CONNECTION .........................................................................................................23 5-4. INSTALLATION.............................................................................
Stand-alone DVR Instruction Manual 5-1. Controls and Connectors (For 8Ch & 16Ch DVR) z Front POWER USB SHUTTLE JOG B DVD R/W HDD LED LINK LED DATA LED A [Fig 5-1 Front View] IR Reciver -A a. 1 Channel(FULL Screen) b. 2 Channel(FULL Screen), UP Key c. 3 Channel(FULL Screen) d. 4 Channel(FULL Screen) e. 5 Channel(FULL Screen), LEFT Key f. 6 Channel(FULL Screen), ENTER Key g. 7 Channel(FULL Screen), RIGHT Key h. 8 Channel(FULL Screen) i. 9 Channel(FULL Screen) j.
5. Installation -B a. Display (Full / Split) b. Emergency Record c. Zoom d. Quick Replay e. OSD On/Off f. Audio g. Stop (ESC) h.
Stand-alone DVR Instruction Manual 5-2. Note for Installation Install the system according to the instructions described in this manual. This product is designed for indoor use and should not be used outdoors. Avoid any area with high humidity or dust which can shorten lifetime of the unit. Choose a well ventilated area and keep minimum of 10” away from obstructions. Do not place the unit near heat generating devices. Do not place items on top of the unit.
5. Installation 5-3.
Stand-alone DVR Instruction Manual 5-4. Installation 5-4.1. Camera Connection ▫ Connection of Normal Cameras Connect the cameras to the Video Input (BNC connector) on the back of the unit as shown above [Fig. 5-3 System Connection]. ▫ Connection of Loop Output The Camera or video output is available from the Video Output (Loop Output) on the back of the unit.
5. Installation ▫ VGA Monitor Connection Connect the VGA Monitor’s connector to the “DSUB 15 Pin Connector” on the rear of the unit. Output for VGA Monitor is the same as that of the main monitor, however it outputs a better quality signal. Pin configuration of VGA Connector. [Fig 5-4 VGA Connector PIN] Number Description Number Description 1 R(75Ω, 0.7Vp-p) 9 N/C 2 G(75Ω, 0.7Vp-p) 10 GND 3 B(75Ω, 0.
Stand-alone DVR Instruction Manual - 5-4.3. Sensor Connection and RELAY IN &OUT ▫ SENSOR Connection (SENSOR IN) Connect up to 16 sensor to ALM (SENSOR) IN. The Sensor should be a contactor type and support N.O. (Normal Open).
5. Installation ▫ RELAY OUT Connection When necessary, use RELAY OUT. The Output of RELAY OUT is a relay contactor type and supports N.O. (Normal Open) & N.C. (Normal Close). The Output capacity is 220V 1A. A higher capacity can cause system failure.
Stand-alone DVR Instruction Manual 5-4.4. RS232C, RS485, RS422 Connection ▫ Connect the cable to the “RS232C/RS485/RS422 PORT” on the rear of the unit. Specification of the RS232C/RS485/RS422 connector is standard for “DSUB9” The Maximum Length of cable is 45 ft with RS232C but RS485 or RS422 is about 300ft.
5. Installation 5-4.5 Connection to an Ethernet Network ▫ Connecting the cable to Ethernet. Our Ethernet connector is a RJ45 type. The maximum cable length is 300 ft. When you want to use a longer cable, we suggest using repeater.
Stand-alone DVR Instruction Manual 5-4.6. POWER CONNECTION Select proper voltage (see fig 5-10) and connect to a reliable power source. It should not be shared with other electrical equipment on the same line. Poor performance can occur if the connected voltage is more than 10% plus or minus the required voltage. Frequent power cuts can cause crucial failures, so if you have an unstable power source we recommend the use of an Uninterrupted Power Supply or other backup power source.
6 6.How to operate CONTENTS 6-1. GENERAL INFORMATION .......................................................................................................33 6-2. OPERATING INTERFACE........................................................................................................34 6-3. IR REMOTE CONTROLLER ....................................................................................................35 6-4. POWER ON/OFF..........................................................................
Stand-alone DVR Instruction Manual CONTENTS 6-7. LIVE..................................................................................................................................41 6-7.1. FULL SCREEN .............................................................................................................................. 41 6-7.2. SPLIT SCREEN ............................................................................................................................. 41 6-7.3.
6. How to Operate 6-1. General Information ▫ You can operate all functions of the system by use of buttons located on the front panel, remote controller and a mouse. Additionally, you can remotely control this unit via RS422C or the Ethernet port located on the back of the unit. ▫ System status is indicated by either LED lights on the operator buttons or the monitor.
Stand-alone DVR Instruction Manual 6-2. Operating Interface There are 3 ways to operate the system by pressing the buttons on the front panel or buttons on the remote controller and clicking the mouse. A lot of users mostly prefer to use a mouse on these kinds of products such as DVRs, computers and computer-aided devices. Therefore we would like to describe all the instructions in this manual based on using the mouse.
6. How to Operate 6-3. IR Remote Controller 1 2 1. Record 2. Power On/Off 3. Display format (Split) 3 4. System status 5. Pan / Tilt 5 6. Zoom / Focus 4 6 7. Search for replaying 7 9 8. Up 8 11 9. Quit 10 12 10. Left 11. Enter 14 13 15 16 17 12. Right 13. Quick Replay 14. Down 18 15. Menu (Setup) 16. OSD On/Off 17. Zoom 19 18. Freeze / IR ID Config 19. No.1~16 Channel (Full Screen) / No. 1 ~ 16 IR ID Config [Fig.
Stand-alone DVR Instruction Manual 6-4. Power On/Off 6-4.1. POWER ON On the front panel or the remote controller: Press the POWER button on the front panel for approx. 3 seconds until the LED lights are turned on or just press the POWER button on the remote controller. 6-4.2. POWER OFF On the front panel or the remote controller: Press the POWER button on the front panel for approx.
6. How to Operate 6-4.3. APPEARANCE OR DISAPPEARANCE OF POWER BUTTON The Power On/Off button and the Audio buttons (See section 6-7.4) as shown in Fig.6-3-1 will always stay on the MENU bar when the system is not connected through the DVR Master (Client Host Program or Internet Explorer). But the Power On/Off button and the Audio buttons on the MENU bar as shown in Fig.
Stand-alone DVR Instruction Manual 6-5. Menu Bar On/Off Right-click on the screen in the LIVE or the RECORD mode and the MENU bar will be appeared. Right-click again and it will be disappeared. CLICK CLICK [Fig.
6. How to Operate 6-6. Display Screen 6-6.1. FULL SCREEN SEQUENCE ICON RECORD ICON CAMERA TITLE [Fig.
Stand-alone DVR Instruction Manual 6-6.2.
6. How to Operate 6-7. LIVE 6-7.1. FULL SCREEN ▫ Full SCREEN is available in the LIVE mode or the RECORD mode. ▫ Click a certain camera’s screen in the LIVE mode or in the RECORD mode, then a FULL SCREEN will be displayed. ▫ Click the FULL screen to return to the SPLIT SCREEN. 6-7.2. SPLIT SCREEN ▫ SPLIT SCREEN is available in the LIVE mode or the RECORD mode. ▫ Click the DISPLAY icon on the MENU bar, then the DISPLAY pop-up screen will be displayed (See Fig.6-6).
Stand-alone DVR Instruction Manual 6-7.3. SEQUENCING SCREENS ▫ Displaying the cameras in SEQUENCE is available in the LIVE mode or the RECORD mode. Each of the channels will be displayed in sequence and the dwell time can be adjusted in the camera set up menu (Refer to section 7-4.7). ▫ This ICON is displayed in the upper left hand corner of the screen while the system is in the Sequencing Mode. ▫ Click a Full screen to return to the SPLIT screen while the system is sequencing.
6. How to Operate 6-7.4. LIVE AUDIO ▫ If cameras (up to 16 cameras) have audio function, it will sound in the live mode. ▫ Click the CHANNEL button you wish to listen on the MENU bar as shown below (See Fig.6-9). The CHANNEL can be changed by clicking the mouse repeatedly. ▫ Turn the AUDIO (speaker) ON by clicking the SPEAKER icon as shown below (See Fig.69).
Stand-alone DVR Instruction Manual 6-7.5. ZOOM The image on the screen will be zoomed up to 2 times when the ZOOM button is clicked in the LIVE mode (This function is available on the full screen mode only). ▫ Click the ZOOM button on the MENU bar in the LIVE mode. ▫ Move the mouse on the ZOOMED screen, and then the 8-directional arrow marks will be appeared as shown below (Fig.6-10). ▫ Click the (EXIT) button to return to the LIVE Mode. [Fig.
6. How to Operate 6-7.6. OSD ON / OFF OSD ON /OFF is possible in the LIVE mode or RECORD mode. ▫ Click the OSD button on the MENU bar to turn the OSD (On Screen Display) ON or OFF. When the OSD is in OFF position, all the texts on the screen will be disappeared. CAM 01 CAM 02 CAM 03 CAM 04 CAM 05 CAM 06 CAM 07 CAM 08 CAM 09 CAM 10 CAM 11 CAM 12 CAM 13 CAM 15 CAM 16 CAM 16 2007/05/25 19:30: 41 [Fig.6-11 OSD ON SCREEN] [Fig.
Stand-alone DVR Instruction Manual 6-7.7. PAN / TILT ▫ Click the PAN/TILT button on the MENU bar in the LIVE mode to access the PAN/TILT cameras. ▫ Click the (EXIT) button to return to the LIVE mode. [Fig.6-13 PAN/TILT button] [Fig.
6. How to Operate PAN / TILT PRESET EXIT ZOOM / FOCUS CHANNEL LEFT RIGHT [Fig.6-15 PAN/TILT CONTROL ▫ Channel Selection and Screen Conversion To change a channel, press the CHANNEL button on the front panel or click the CHANNEL button on the [Fig.6-15 PAN /TILT CONTROL window]. It will be converted a full screen. To return to the LIVE mode, press the SPLIT button on the front panel or click the (EXIT) button. ▫ ZOOM / FOCUS Control the ZOOM and FOCUS of PAN/TILT camera.
Stand-alone DVR Instruction Manual ▫ PRESET [Fig.6-15-1 Preset Menu] It is a function to preset the PTZ camera(s) which you wish to monitor frequently. Preset Setup - Select a position of camera you wish to preset and click the SET button in Fig.6-15-1. - Click the number(s) for the current position of camera. - Delete the numbers by using ← button. Preset Execution Click the number(s) which you preset and click GO button to move the camera.
6. How to Operate 6-7.8. SYSTEM STATUS ▫ Click the SYSTEM STATUS button on the MENU bar to see the system status as shown below (Fig.6-16). ▫ Click the (EXIT) button to return to the LIVE mode or RECORD mode. [Fig.6-16 SYSTEM STATUS button] [Fig.
Stand-alone DVR Instruction Manual 6-7.9. POWER LOSS LISTS The list indicates the time/date when the system power was turned OFF. ▫ Click the POWER LOSS LISTS button on the SYSTEM STATUS window to view the POWER LOSS LISTS. ▫ Each of the pages contains 10 lists. You can search the pages by clicking the UP/DOWN button. ▫ Click the (EXIT) button to return to the LIVE or RECORD mode. [Fig.
6. How to Operate ▫ CLEAR LISTS button Click the CLEAR LISTS button to clear the lists, you will be prompted to confirm changes. When you click the OK button, the POWER LOSS LISTS will be deleted. To cancel, click the CANCEL button Fig.
Stand-alone DVR Instruction Manual 6-7.10. VIDEO LOSS LIST The list indicates the video loss channel and the time/date when the video signal was disconnected. ▫ Click the VIDEO LOSS LISTS button on the SYSTEM STATUS window to view the VIDEO LOSS LISTS. ▫ Each of the pages contains 4 lists. You can search the pages by clicking the UP/DOWN button. ▫ Click the (EXIT) button to return to the LIVE or RECORD mode. [Fig.6-20 VIDEO LOSS LISTS window] [Fig.
6. How to Operate ▫ CLEAR LISTS button Click the CLEAR LISTS button to clear the lists, you will be prompted to confirm changes. When you click the OK button, the VIDEO LOSS LISTS will be deleted. To cancel, click the CANCEL button [Fig.
Stand-alone DVR Instruction Manual 6-8. Record This system provides Watchdog function. When power goes off during recording and the power turns on, the system will automatically start recording. 6-8.1. Manual (Continuous) recording ▫ Click the SETUP icon on the MENU bar in the LIVE mode. ▫ Click the RECORD button in the SETUP menu and then the RECORD window will be displayed. ▫ Select the MANUAL RECORDING ( and the TIMER RECORDING ( ) between the MANUAL RECORDING ( ) as shown in Fig.6-23.
6. How to Operate this recording mode. ▫ Press the RECORD button on the front panel or click the RECORD icon on the MENU bar. [Fig.6-24 Manual Event Recording setup] 6-8.3. Timer Recording ▫ Click the SETUP icon on the MENU bar in the LIVE mode. ▫ Click the RECORD button in the SETUP menu and the RECORD window will be displayed. ▫ Select the TIMER RECORDING ( and the TIMER RECORDING ( ) between the MANUAL RECORDING ( ) as shown in Fig.6-25.
Stand-alone DVR Instruction Manual 6-8.4. Timer Event Recording ▫ Click the SETUP icon on the MENU bar in the LIVE mode. ▫ Click the RECORD button in the SETUP menu and the RECORD window will be displayed. ▫ Select the TIMER RECORDING ( and the TIMER RECORDING ( ) between the MANUAL RECORDING ( ) as shown in Fig.6-26. All channels can be set at ) or each of the channels can be set by the same time by clicking the ALL ( ) on the CAM 1 through CAM 16.
6. How to Operate 6-8.5. Recording Icons The Recording Icons depends on recording modes are displayed in the upper left hand corner of the screen. ▫ To turn the Recording Icon OFF, click the DISPLAY ON in the RECORD menu and then it will be turned OFF. You can select the value ON or OFF by repeatedly clicking the mouse. Manual (Continuous) Recording Event Recording Ready MOTION Event Recording SENSOR Event Recording [Fig.
Stand-alone DVR Instruction Manual 6-9. REPLAY 6-9.1. QUICK REPLAY It is available only by pressing the PLAY button on the front panel or the QICK SEARCH button on the remote controller. ▫ Press the PLAY button, then the recent recorded list will be played. 6-9.2. REPLAY ▫ Click the REPLAY icon on the MENU bar, then the REPLAY window as shown in Fig.6-29 will be displayed. ▫ Click the (EXIT) button to return to the previous mode. [Fig.
6. How to Operate 6-9.2.1. Playback Devices In order to payback, plug the USB devices such as external USB HDD, USB memory to the USB port or insert a recorded media (CD-R/W or DVD-R/W) into the DVD-R/W drive. When the devices are ready to playback, the Ready on the corresponding devices will be displayed as shown in Fig.6-30. ▫ Click the mouse on a device among HDD, USB, CD-R/W and DVD-R/W that is displaying the Ready (See Fig.6-30). The corresponding LED will be lit in red when the device is selected.
Stand-alone DVR Instruction Manual ▫ Select the hour on the Start Time Select Window (See Fig.6-32) by clicking the mouse on the Hour (0 – 23 hour) you wish to start to play. The green active buttons indicate the HOUR that contains recorded data, and the red active buttons indicate the selected Start HOUR. [Fig.6-32 Start Time Select window] By using the Replay Time set-up buttons: The time and date can also set on the Replay Time set-up button window (See Fig.6-33).
6. How to Operate 6-9.2.3. Replaying Replaying start time set-up can be possible within a recording time extent. ▫ Replay buttons (NORMAL / MOTION / SENSOR) NORMAL PLAY: Click the button to play all the recorded data. MOTION PLAY: Click the button to play the recorded data by MOTION only. SENSOR PLAY: Click the button to play the recorded data by SENSOR only.
Stand-alone DVR Instruction Manual ▫ How to control the buttons while replaying ① ③ ④ ② ④ ③ ⑤ ⑥ [Fig.6-35 Replay screen] ① Search Slider It is possible to playback by clicking the slider on the bar and dragging it. ② PLAY / PAUSE Click the button to pause. Click the button to replay when in the pause mode. ③ REW/FF During replaying, press the or button, or turn the shuttle ring on the front panel for fast rewinding and fast forwarding up to 128 times.
6. How to Operate ④ PREV / NEXT During replaying, press the the button to view previous frame in still image and press button to view the next frame in still image. ⑤ Speaker ON / OFF Turn speaker ON or OFF. ⑥ Speaker Volume Adjust the Audio Volume by clicking the ▲ or the ▼ button when the AUDIO is turned ON. 6-9.2.4. Disappearance of Replay control buttons During replaying, the replay control buttons appear on the bottom of the screen.
Stand-alone DVR Instruction Manual - Click the mouse on one out of channels during replaying to view a full screen. - Click the mouse on the full screen during replaying to return to the split screen. [Fig.6-36 SPLIT screen during replaying] [Fig.
6. How to Operate 6-10. COPY ▫ Click the COPY icon on the MENU bar, and then the COPY window as shown in Fig.6-38 will be displayed. ▫ Click the (EXIT) button to return to the previous mode. [Fig.6-38 COPY window] 6-10.1. Copying devices In order to copy the recorded data, plug the USB devices such as external USB HDD, USB memory to the USB port or insert a blank media (CD-R/W or DVD-R/W) into the DVD-R/W drive.
Stand-alone DVR Instruction Manual ▫ Connect the USB devices to the DVR ▫ Click the SETUP icon on the MENU bar, and the SETUP menu will be displayed. ▫ Click the DISK MANAGER in the SETUP menu, and the DISK MENAGER will be displayed. ▫ Click the mouse on the USB button in the DISK MANAGER, and you will be asked. ▫ Click the OK, and then the progressive bar will be shown along with FORMATTING USB….
6. How to Operate ① All channels, HOUR selection button ② HOUR selection button ③ channel selection button [Fig.6-40 Copy Start time and Channel Selection window] ① All channels, HOUR selection button. Click the arrow button on the upper left corner as shown in Fig.6-40 to set the full extent of the recording and all the channels simultaneously. ② HOUR selection button Select the start time to copy by clicking the mouse on HOUR (0-23: in the military hour).
Stand-alone DVR Instruction Manual [Fig.6-41 Copy Start/End setup buttons] By using the Start/End set-up bar: The starting time to copy can also be set by clicking the slider on the bar and dragging it or just click the bar. [Fig.6-42 Copy Start/End setup bar] 6-10.3. Set the Copy End Time (Copying extent) Refer to the above explanation (See section 6.10.2.).
6. How to Operate 6-10.4. Copying the recorded data during replaying The system, CDR1650 allows users to copy the recorded data during replaying. ▫ Start replaying (See section 6-9). ▫ Right-click on the replaying screen, and the COPY DATA screen will be displayed (See Fig.6-43).
Stand-alone DVR Instruction Manual [Fig.6-44 End Copy Time Setup window] ▫ Choose one among NETWORK, USB, CD and DVD which are ready to copy (See section 6-10.1). Select COPY Mode Only when the devices and Medias are ready to copy, the Ready on the corresponding devices and Medias will be displayed. NETWORK COPY Save the recorded data in PC through the DVR Master by Network. Click the Network button on the DVR Master to start copy.
6. How to Operate DVD-RW COPY Save the recorded data on DVD-R/W Medias. Click the DVD-R/W button to start copy. ▫ As soon as one of the above buttons is clicked , copying will start along with displaying the icon shown in Fig.6-45. The following icon indicates that copying is in process. [Fig.
Stand-alone DVR Instruction Manual 72
7 7.SETUP CONTENTS 7-1. SETUP..............................................................................................................................76 7-2. SYSTEM ...........................................................................................................................77 7-2.1. TIME / DATE .................................................................................................................................. 78 7-2.2. SYSTEM CONFIG .........................................
Stand-alone DVR Instruction Manual CONTENTS 7-4. CAMERA ..........................................................................................................................89 7-4.1. Camera ON/OFF ........................................................................................................................... 90 7-4.2. Camera Name (Camera Title) ....................................................................................................... 90 7-4.3. Buzzer ..........................
7. Setup CONTENTS 7-7. NETWORK ..................................................................................................................... 116 7-7.1. IP Mode........................................................................................................................................ 116 7-7.2. GATEWAY, SUBNET, IP ADDRESS............................................................................................ 117 7-7.3. Port............................................................
Stand-alone DVR Instruction Manual 7-1. SETUP [Fig.7-1 Setup Icon on MAIN MENU] It is possible to set up the menus in the LIVE mode and partly in the RECORD mode. ▫ Click the “SETUP” button on the MENU bar and then the SETUP menu will be displayed. ▫ Click the “EXIT” button to return to the previous mode. [Fig.
7. Setup 7-2. SYSTEM ▫ Click the “SYSTEM” button in the SETUP menu, and then the SYSTEM menu shown in Fig.7-3 will be displayed. ▫ Click the “EXIT” button to return to the SETUP menu. . [Fig.
Stand-alone DVR Instruction Manual 7-2.1. TIME / DATE ▫ Click the “TIME/DATE” button in the SYSTEM menu, and then the TIME/DATE menu will be displayed (See Fig.7-4). ▫ Click the “EXIT” button to return to the SYSTEM menu. [Fig.7-4 TIME / DATE menu] ▫ TIME FORMAT Click the mouse on the TIME FORMAT button to change and then select 24 HOUR or 12 HOUR by clicking the mouse. [Fig.
7. Setup ▫ DATE FORMAT There are three formats to display the time and date as follow. • MM / DD / YYYY: For U.S.A. • YYYY / MM / DD: For Asian countries. • DD / MM / YYYY: For European countries. Click the mouse on the DATE FORMAT button to change, and then select a DATE FORMAT among YYYY/MM/DD, DD/MM/YYYY and MM/DD/YYYY. [Fig.
Stand-alone DVR Instruction Manual 7-2.2. SYSTEM CONFIG ▫ Click the “SYSTEM CONFIG” button in the SYSTEM menu, and then the SYSTEM CONFIG menu will be displayed (See Fig.7-10). ▫ Click the “EXIT” button to return to the SYSTEM menu. [Fig.7-10 SYSTEM CONFIG] 7-2.2.1. FACTORY DEFAULT ▫ Click the “FACTORY DEFAULT” button in the SYSTEM CONFIG menu, and you will be asked as shown in Fig.7-12. [Fig.7-11 Factory Default button] ▫ Click the “OK” button in Fig.
7. Setup [Fig.7-12 Confirmation window of Factory Default] 7-2.2.2. LOAD CONFIG / BACKUP CONFIG You can save up to four different settings in the BACKUP CONFIG and load the files in the LOAD CONFIG to change the settings to the system. ▫ LOAD CONFIG This function is to load the changed settings to the system. - Click the LOAD CONFIG button and then the LOAD CONFIG window will be displayed (See Fig.7-14).
Stand-alone DVR Instruction Manual [Fig.7-14 LOAD CONFIG window] ▫ BACKUP CONFIG This function is to save the current settings to load the settings to the system. Save the current settings in the BACKUP CONFIG in order to load it to the system in the near future whenever you need to change the settings. - Click the BACKUP CONFIG button and then the BACKUP CONFIG window will be displayed (See Fig.7-16).
7. Setup 7-2.3. PASSWORD ▫ ON/OFF Select ON or OFF by clicking the mouse. If the ON is selected, the password has to be entered to get into the SETUP mode, RECORD mode, COPY mode, REPLAY mode, and when trying to connect the network through the DVR Master. ▫ PASSWORD CHANGE Click the password “********” button and then the On Screen Keyboard will be displayed as shown in Fig.7-17. The factory default password is “11111111”. Delete the existing password with the button on the On Screen Keyboard.
Stand-alone DVR Instruction Manual 7-2.4. IR REMOTE ID Up to 16 DVR systems can be controlled by only one remote controller we provided, but IDs should be assigned on each of the systems. You don’t have to assign any ID on the single unit and you can control the system with the provided remote controller without IR REMOTE ID, which is in the OFF mode (Skip this section). ▫ Click the IR REMOTE ID button and select one among OFF, 1 through 16 to assign an ID on the system by clicking the mouse. [Fig.
7. Setup 7-2.5. FIRMWARE UPDATE There are two ways to update the firmware through USB memory and the DVR Master (GUI). We recommend users to update the firmware only in the LIVE mode. ▫ By USB memory - Format the USB with your computer and save the firmware file on it (not including folder). - Plug it on the USB port on the DVR. - Click the mouse on the SELECT button in the SYSTEM menu and the FIRMWARE LIST will be displayed. - Click on the list, and then you will be asked, OK or CANCEL.
Stand-alone DVR Instruction Manual 7-3. DISK MANAGER ▫ Click the “DISK MANAGER” button in the SETUP menu and then the DISK MANAGER window will be displayed (See Fig.7-22). ▫ Click the (EXIT) button to return to the SETUP menu. ▫ A DVD R/W and 3 Hard Disk Drives can be installed, and all information in regards to the drives will automatically display on the DISK MANAGER window. [Fig.
7. Setup 7-3.1. HDD WRITE FAIL If HDD is in full and the OVERWRITE on the HDD is turned OFF in the recording mode, the system will activate the relay output (See section 5-4.3) for a siren or other device. ▫ Click the HDD WRITE FAIL button in the DISK MANAGER window and select one among RELAY 1 OUT, RELAY 2 OUT, RELAY 3 OUT, RELAY 4 OUT or DISABLE. [Fig. 7-23 HDD Write Fail button] 7-3.2. HDD OVERWRITE ▫ Click the mouse on the OVERWRITE button to select the ON or the OFF.
Stand-alone DVR Instruction Manual [Fig.
7. Setup 7-4. CAMERA ▫ Click the “CAMERA” button in the SETUP menu and then the CAMERA menu will be displayed (See Fig.7-26). To change the settings in the CAMERA menu, stop recording by clicking the RECORD icon on the MENU BAR. It is possible only in the LIVE mode. ▫ Click the UP/DOWN button on the right hand side of the menu to switch the page. ▫ Click the (EXIT) button to return to the SETUP menu. [Fig.
Stand-alone DVR Instruction Manual 7-4.1. Camera ON/OFF ▫ Click on each of the channels to select the “O” or “X” in the CAMERA menu. If the “O” is selected, the corresponding video channels (CAM 01 through CAM 016) will be displayed on the screen. If the “X” is selected, the corresponding video channels (CAM 01 through CAM 016) won’t be displayed. [Fig.7-27 Camera ON/OFF button] 7-4.2.
7. Setup 7-4.3. Buzzer In order to alert users, the Buzzer will sound at that time video signal lost. ▫ Click on each of the channels you wish to turn the buzzer “ON” or “OFF”. If the “O” is selected, the buzzer will sound when video signal lost and if the “X” is selected, the buzzer won’t sound. [Fig.7-29 Buzzer button] 7-4.4. Relay The system will automatically activate sirens or other devices through the Relay Outputs on the rear panel when video signal lost.
Stand-alone DVR Instruction Manual 7-4.5. Pan/Tilt Settings ▫ Click the PAN/TILT button on the corresponding channels in the CAMERA menu, then the PAN/TILT window will be displayed as shown in Fig.7-33. ▫ Click the (EXIT) button to return to the CAMERA menu. [Fig.7-32 PAN/TILT button] [Fig.7-33 PAN/TILT window] ▫ PTZ ID - Click the PTZ ID button in the PAN/TILT window, then On Screen Keyboard will show up.
7. Setup ▫ Pan/Tilt Vendor select Click the “PAN/TILT & REMOTE” button in the PAN/TILT window, then the vendor lists will show up. Select a vendor on the vendor lists by clicking the mouse. Fig.7-34 PAN/TILT & REMOTE [Fig.7-35 PAN/TILT Vendor lists] ▫ Model Click the “MODEL” button in the PAN/TILT window and select the model on the pop-up lists by clicking the mouse. [Fig.7-36 MODEL button] [Fig.
Stand-alone DVR Instruction Manual ▫ Baud rate Click the “BAUD RATE” button in the PAN/TILT window and choose a value among 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps on the Baud Rate pop-up window by clicking the mouse. [Fig.7-38 BAUDRATE button] [Fig.7-39 Baud Rate pop-up window] ▫ Data Bits Click the “DATA BITS” button in the PAN/TILT window and choose a value among 5, 6, 7 and 8 on the Data Bits pop-up window by clicking the mouse. [Fig.
7. Setup ▫ Stop Bits Click the “STOP BITS” button in the PAN/TILT window and select 1 or 2 on the Stop Bits pop-up window by clicking the mouse. [Fig.7-42 STOP BITS button] [Fig.7-43 Stop Bits pop-up window] ▫ Parity Bit Click the “PARITY BITS” button in the PAN/TILT window and choose a value among NONE, ODD, EVEN, STICK and ZERO on the Parity Bits pop-up window by clicking the mouse. [Fig.7-44 PARITY BIT button] [Fig.
Stand-alone DVR Instruction Manual 7-4.6 Display ▫ Click the DISPLAY button in the CAMERA menu and select the ON or OFF. If the “ON” is selected, the camera name (camera title) in the LIVE mode will be displayed on the screen. If the “OFF” is selected, the camera name (camera title) in the LIVE mode won’t be displayed. [Fig.7-46 Display ON/OFF button] 7-4.
7. Setup 7-5. AUDIO ▫ Click on the AUDIO button in the SETUP menu and then the AUDIO menu will be displayed on the screen. ▫ Click the UP/DOWN button on the right hand side of the menu to switch the page. ▫ Click the (EXIT) button to return to the SETUP menu. [Fig.7-49 AUDIO menu] 7-5.1. Audio Recording ON/OFF ▫ Click the REC (audio recording) button in the AUDIO menu and select the “O” or “X” by clicking the mouse.
Stand-alone DVR Instruction Manual 7-6. RECORD ▫ Click the “RECORD” button in the SETUP menu and then the RECORD menu will be displayed as shown in Fig.7-52. ▫ Click the UP/DOWN button on the right hand side of the menu to switch the page. ▫ Click the (EXIT) button to return to the SETUP menu. [Fig.7-52 RECORD menu] 7-6.1. Record ICON Display ▫ The Recording Icons depends on recording modes are displayed in the upper left corner of the screen.
7. Setup 7-6.2. All Manual / Timer recording button ▫ Click the All Manual / Timer recording button in the RECORD menu, then the All Manual / Timer recording button will be displayed as shown in Fig.7-55. ▫ Select the Manual Recording button or Timer Recording button for all the channels by clicking the mouse in Fig.7-55. ▫ See section 6-8.1 through 6-8.5 on page 54 through 57 for more information related to recording. [Fig.7-54 All Manual / Timer button] [Fig.
Stand-alone DVR Instruction Manual 7-6.3. All Motion ON / OFF, Sensitivity and Velocity Setting ▫ Click the button in the RECORD menu, then the ALL MOTION setup pop-up window will be displayed as shown in Fig.7-57. ▫ By clicking the mouse, select the on the pop-up window (See Fig.7-57) to enable the system to start recording by motion detection for all the channels. ▫ By clicking the mouse, select the on the pop-up window (See Fig.
7. Setup 7-6.4. All Sensors ON / OFF ▫ Click the button in the RECORD menu, then the ALL SENSOR setup pop-up window will be displayed as shown in Fig.7-60. ▫ By clicking the mouse, select the on the pop-up window (See Fig.7- 60) to enable the system to start recording by Sensor (Passive Infrared Sensor) for all the channels. ▫ By clicking the mouse, select the on the pop-up window (See Fig.7-60) to disable the system to start recording by Sensor (Passive Infrared Sensor) for all the channels. [Fig.
Stand-alone DVR Instruction Manual 7-6.6. Recording Speed ▫ Click the F/S (Frames Per Seconds: Recording Speed) button on each of the channels in the RECORD menu, then the Recording Speed pop-up window will be displayed as shown in Fig.7-64. ▫ Select one of the Recording Speed among AUTO, 30, 15, 10, 7, 5, 3, 2, 1 and OFF on the pop-up window by clicking the mouse. ▫ If the AUTO is selected on all the channels, the Recording Speed on all the channels should be the same.
7. Setup NTSC 30 25 15 12 10 8 7.5 6 5 5 PAL 3 3 2 2 1 1 OFF OFF [Fig.7-65 Recording Speed for each channel] 7-6.7. Recording Quality ▫ Click the QUALITY button on each of the channels in the RECORD menu, then the QUALITY pop-up window will be displayed as shown in Fig.7-67. ▫ Select one of the Recording Quality among LOW, NORMAL, HIGH and BEST on the popup window by clicking the mouse. [Fig.7-66 Record Quality button] [Fig.
Stand-alone DVR Instruction Manual 7-6.8. Recording Mode The factory default setting for Recording is the Manual Recording (or called Continuous Recording), which keeps recording continuously if the OVERWRITE is set ON in the DISK MANAGE menu. This Manual Recording mode is not only one of the most popular Recording modes for users, but also one of the most convenient Recording modes to use. Users can select one of the following Recording modes depends on their application. 7-6.8.1.
7. Setup 7-6.9. Recording by Motion Detection When the menu of motion is properly set up (See section 7-6.3 for all the channels and this section for each of the channels) and detected motion of objects, the system begins recording automatically. The recording icon on the MENU bar should be selected in this recording mode. If not, it won’t be recording. ▫ Click the mouse on the button for each of the channels in the RECORD menu and then the MOTION menu will be displayed on the screen as shown in Fig.
Stand-alone DVR Instruction Manual ▫ Pre-Alarm Time Setup Allows you to record a section of video just prior to Motion or Sensor activation. Click the mouse on the PRE in the MOTION menu and choose one of the values among 0, 1, 2, 3, 4 and 5 seconds with the mouse’s wheel, and then click it to save. [Fig.7-70 Pre-Record Time setup button] [Fig.7-71 Pre-Alarm Time Setup pop-up window] ▫ Motion Hold Time Setup The system continues recording for the MOTION HOLD TIME and finishes the recording.
7. Setup ▫ Spot Setup If the “ON” is selected by clicking the mouse on the SPOT button in the MOTION menu, a full screen will display when a motion is detected. If the “OFF” is selected, the full screen won’t be displayed even though motion of objects is detected. [Fig.7-73 Spot Setup button] ▫ Region The Motion Detection Area displays in blue on the screen, and it turns to yellow color when the motion is detected. The white color on the screen represents none of detection area.
Stand-alone DVR Instruction Manual - All Clear Click the ALL CLEAR button in the MOTION menu in order to clear the Motion Detection Area, and then the window turns to white color as shown in Fig.7-77. Right-click on the current window to return to the MOTION menu. [Fig.7-76 ALL CLEAR button] CURSOR [Fig.
7. Setup By Window Set Click the WINDOW SET button in the MOTION menu on each of the cameras and click one of cells (330 cells in total) for the starting point of the area which you would like to designate, and then click the other one of cells for the ending point of area until the motion detection area is the size you want it to be. The multiple motion areas can be set on each of cameras. The motion detection by Window Set will be made on the designated area only.
Stand-alone DVR Instruction Manual - Window Clear Click the WINDOW CLEAR button in the MOTION menu in order to clear the Motion Detection Area, and then the window you already created the motion detection area will be displayed. Click the starting point and the ending point as much as you wish to clear or it can be cleared by ALL CLEAR as described above (See ALL CLEAR). Right-click on the current window to return to the MOTION menu. [Fig.7-80 WINDOW CLEAR button] CURSOR [Fig.
7. Setup By Each Cell Click the EACH CELL button in the MOTION menu on each of the cameras and click the mouse on each of the cells as much as you would like to designate the Motion Detection Area. To clear, click the designated cells. Right-click on the current window to return to the MOTION menu. [Fig.7-82 EACH CELL button] CURSOR [Fig.
Stand-alone DVR Instruction Manual ▫ Map View Click the MAP VIEW button in the MOTION menu to view the current settings for Motion detection area. Right-click on the current window to return to the MOTION menu. [Fig.7-84 MAP VIEW button] CURSOR [Fig.7-85 Map View screen] Note : Please pay attention to the following directions in order to use the Motion Detection function properly: • Adjust the sensitivity level and motion area to fit your requirements.
7. Setup 7-6.10. Recording by Sensor (PIR Sensor) ▫ Click the mouse on the button for each of the channels in the RECORD menu and then the SENSOR menu will be displayed on the screen as shown in Fig.7-86. ▫ Click the (EXIT) button to return to the RECORD menu. [Fig.7-86 SENSOR window] ▫ ON/OFF The system will start to record when Alarm is detected and the ON is selected in the SENSOR menu by clicking the mouse. If the OFF is selected, the system won’t be recording.
Stand-alone DVR Instruction Manual ▫ Pre-Alarm Time Setup Allows you to record a section of video just prior to Sensor activation. Click the mouse on the PRE in the SENSOR menu and choose one of the values among 0, 1, 2, 3, 4 and 5 seconds with the mouse’s wheel, and then click it to save. [Fig.7-88 Pre-Alarm Time Setup button] [Fig.
7. Setup ▫ Alarm Hold Time Setup The system continues recording for the Alarm HOLD TIME and finishes the recording. Click the mouse on the HOLD in the SENSOR menu and choose one of the values among 1 through 30 seconds with the mouse’s wheel, and then click it to save. [Fig.7-90 Alarm Hold Time Setup button] ▫ Spot Setup If the “ON” is selected by clicking the mouse on the SPOT button in the SENSOR menu, a full screen will display when a motion is detected.
Stand-alone DVR Instruction Manual 7-7. NETWORK ▫ Click the “NETWORK” button in the SETUP menu and then the NETWORK menu will be displayed on the screen as shown in Fig.7-92. ▫ Click the 7-7.1. IP Mode (EXIT) button to return to the SETUP menu. [Fig.7-92 NETWORK menu] When the system uses the same IP address every time it connects to the network, it is known as a static IP address. If the system’s IP address changes frequently, it is called a dynamic IP address.
7. Setup [Fig.7-93 IP Mode button] [Fig.7-94 IP Mode pop-up window] 7-7.2. GATEWAY, SUBNET, IP ADDRESS ▫ Click the GATEWAY / SUBNET / IP ADDRESS button in the STATIC IP MODE and then the On Screen Keyboard will appear. ▫ Delete the current values with the button and enter the address numbers by using On Screen Keyboard, and then click OK button to set with new address. ▫ Click the CANCEL button to return to the original values. [Fig.7-95 Address Setup window] [Fig.
Stand-alone DVR Instruction Manual 7-7.3. Port ▫ PORT is the TCP address of the program, which is used to connect to the network viewer. It can be set from 1 to 65535 values. ▫ Click the PORT button and then the On Screen Keyboard will show up. ▫ Delete the current port number with the button and enter the new port number by using On Screen Keyboard, and then click “OK” button to set with new port number. ▫ Click the “CANCEL” button to return to the default value. [Fig.7-97 Port Setup window] [Fig.
7. Setup 7-7.4. MAC ID ▫ MAC ID is connecting address for Ethernet, every unit has 12 digit address (HEX 6 byte). MAC ID was already assigned with the factory default value. User can not change it. 7-7.5. MNS (MAC NAME SERVER) As a sort of DDNS, two servers in our company (CLOVER) are being operated so that our client can access DVR with a Dynamic IP address. If one of servers stops operating, the other one will automatically start working.
Stand-alone DVR Instruction Manual ▫ IP ADDRESS / PORT DO NOT CHANGE THE IP ADDRESS AND PORT NUMBER IN THE MNS MENU IF YOU DON’T HAVE ANY SPECIAL SERVER TO ACCESS YOUR DVR WITH A DYNAMIC IP ADDRESS. IF YOU CHANGE THEM, YOU CAN’T NOT ONLY USE OUR MNS (MAC NAME SERVER), BUT ALSO YOUR NETWORKING WILL BE DISCONNECTED. ▫ SITE NAME The SITE NAME is one of the important factors to access the DVR through MNS (MAC NAME SERVER) with the DVR Master (GUI).
7. Setup 7-7.6. DDNS (DYNAMIC DOMAIN NAME SYSTEM) ▫ Select the DDNS button in the NETWORK menu by clicking the mouse, pressing the buttons on the front panel or remote controller. The DDNS menu will show up as shown in Fig.7-103. ▫ To return to the NETWORK menu, Click the (EXIT) button. ▫ If you were in the middle of entering values on the DDNS menu, you can’t exit by clicking the mouse. Choose the SERVER button in the DDNS menu by clicking the mouse and (EXIT) button.
Stand-alone DVR Instruction Manual ▫ HOST NAME - Click the HOST NAME in the DDNS menu and type the HOST NAME registered to the DDNS server such as DYNDNS.ORG and NO-IP.ORG by using the On Screen Keyboard. - After changing the values, click on the OK button. [Fig.7-105 HOST NAME button] ▫ USER ID - Click the USER ID in the DDNS menu and type the USER ID registered to the DDNS server by using the On Screen Keyboard. - After changing the values, click on the OK button. [Fig.
7. Setup 7-7.7. HOW TO SETUP AND USE THE DDNS 7-7.7.1. Router. It has to be set as a virtual server (or port forwarding) in order to utilize the DDNS. There are a lot of manufacturers on the market. Please read the provided manual thoroughly before setting or visit our website at www.cloverusa.com in regards to do it. We, the manufacturer of DVR systems will not support the solution to your individual network issues.
Stand-alone DVR Instruction Manual 7-7.8. EMAIL NOTIFICATION ▫ Email notification enables to notify events (sensor, motion, video loss, power on/off, power loss, record on/off, record fail, replay or copy start/stop) by sending emails to one or two email accounts. [Fig.
7. Setup ▫ EMAIL ADDRESS SETUP [Fig.7-109 Email Address setup] - Click one of email address boxes and then the On Screen Keyboard will show up as shown Fig.7-109. - Delete the current email address with the button and enter an email address by using the On Screen Keyboard. - If necessary, click the button to enter upper cases. - Click the OK button to save. - Click the check box below to enable the email notification. [Fig.7-110 Check Box for email] Note : If a check box in Fig.
Stand-alone DVR Instruction Manual ▫ EVENT Setup - Click the check boxes below to choose the events you need. - To delete, click the check box again. [Fig.7-111 Event setup] ▫ INTERVAL TIME Setup - Click the INTERVAL TIME (see Fig.7-112) to set the interval time of sending emails and then choose the time (in minutes) on the pop-up window by clicking the mouse. If the 10 minutes is selected, the system will automatically send only one email every 10 minutes even though a lot of events occur. [Fig.
7. Setup Note : If the motion is selected in Fig.7-112, you may receive numerous emails from the DVR systems due to a couple of factors such as continuous moving objects, a strong and changing lighting source, low resolution and noises of cameras. In case of this, select a longer INTERVAL TIME and refer to “Note for Motion Detection Function” on page 112. 7-8.
Stand-alone DVR Instruction Manual 7-8.1. VIDEO ENHANCEMENT ON EACH CAMERA ▫ Click on an INPUT button in the VIDEO ENHANCE menu. ▫ The CONTRAST and BRIGHTNESS sliders will be displayed along with camera picture as shown in Fig.7-114. ▫ Adjust Contrast and Brightness with the sliders by clicking the mouse. ▫ To return to the VIDEO ENHANCE menu, Click the [Fig.7-114 CAMERA INPUT] 128 (EXIT) button.
7. Setup 7-8.2. VIDEO ENHANCEMENT ON VGA OUTPUT ▫ Click on the VGA OUTPUT in the VIDEO ENHANCE menu. ▫ The CONTRAST, BRIGHTNESS and SATURATION sliders will be displayed along with camera picture. ▫ Adjust Contrast, Brightness and saturation with the sliders by clicking the mouse. ▫ To return to the VIDEO ENHANCE menu, Click the [Fig.7-115 VGA OUTPUT] 129 (EXIT) button.
Stand-alone DVR Instruction Manual 130
8 8.
Stand-alone DVR Instruction Manual CONTENTS 8-1. REMOTE PROGRAM OVERVIEW ..........................................................................................133 8-2. INSTALLING THE PROGRAM TO PC ......................................................................................134 8-3. INTERNET EXPLORER.........................................................................................................135 8-4. REMOTE HOST .......................................................................
8. Remote Host Program 8-1. Remote Program Overview The Remote Host Program allows you to view live video, search archived video, control PTZ cameras and to set up the exact same menus as the DVR does. The DVR system can have up to 10 simultaneous Remote Connections. Each user can performs on the DVR system and will not affect the other users. The only exception to this is accessing Setup. Only one user is allowed to access Setup at any time.
Stand-alone DVR Instruction Manual 8-2. Installing the Program to PC Install the program into PC by using program CD (supplied) as follows. How to install the program 1. Start the operating system (Windows 2000/XP/VISTA). 2. Insert the program CD into CD-ROM drive. 3. Open My Computer, and then select CD-ROM drive. 4. Double click Setup.EXE. The software installation will begin. 5. After the installation has been completed, the DVR Master icon will be created on your desktop screen as shown below. 7.
8. Remote Host Program 8-3. Internet Explorer When you are trying to use this function, it is highly recommended that the password should be turned ON in the SYSTEM menu not to enable unauthorized personnel to access your DVR system (See section 7-2.3). Up to 10 users can remotely access your DVR with the HOST NAME. How to setup the Internet Explorer • Registration to the www.dyndns.org (See section 7-7.7.2 on page 123).
Stand-alone DVR Instruction Manual • Click on the following message. This site wants to install the following add-on: ‘DVR Master’ from ‘Clover Electronics USA’. If you trust the website and the add-on and want to install it, click here…. • Click on the click install ActiveX Control…. on the pop-up screen and the following window will be displayed. [Fig.8-4 Install the DVR Master] • Click on the Install button on the above window (See Fig.8-4) and the DVR Master will be shown.
8. Remote Host Program 8-4. Remote Host ① ② ③ ④ ⑤ ⑥ ⑦ ⑧⑨⑩ ⑪ 12 ○ 15 ○ 13 ○ 16 ○ [Fig 8-5.
Stand-alone DVR Instruction Manual Table. Description of Remote Host Program Button ① Minimization Button ② Close Button ③ Current Time ④ Connection Button ⑤ Setup Button ⑥ Player Execution Button ⑦ Capture Button ⑧ Multi-Mode ⑨ Terminal Mode ⑩ E-map Button ⑪ Splits the screen in 4, 9 & 16ch. 1 ○2 PAN /TILT Control Button ( Control the PTZ camera from the remote site DVR) 13 ○ Depending on the mode, it displays Status/REPLAY / COPY information.
8. Remote Host Program 8-4.1. Setup ① ② ③ ④ [Fig.8-6 HOST CONFIG window] ① Version number It represents the current version number of the Firmware. ② Copy Refer to Section 8-4.10 in regards to copying methods after selecting one between the Quick Copy and the Live + Copy. ▫ Quick Copy Click on the Quick Copy for faster copying the recorded data from the DVR to the Host Program (DVR Master) without live images. The copying speed of the Quick Copy is faster than the Live + Copy.
Stand-alone DVR Instruction Manual ③ Network Image ▫ Size Choose a Size (Resolution) among D1, Half D1 and CIF you wish to display on the DVR Master by clicking the mouse. This setting does not affect the DVR. ▫ Quality Choose one among LOW, NORMAL, HIGH and BEST you wish to display on the DVR Master by clicking the mouse. This setting does not affect the DVR.
8. Remote Host Program 8-4.2. Connection There are two ways to access the DVR through the DVR Master as follows. ▫ With Set Direct setting - Click the “CONNECT” button on the DVR Master and then the “Connect Dialog menu” as shown in Fig. 8-8 will be displayed. - Click the “Set Direct” in the Connect Dialog menu and click the “EDIT” button. - Enter the IP address (or WAN IP address of the Router) and Port number, which must be the same as DVR has.
Stand-alone DVR Instruction Manual [Fig.8-8 Connect Dialog] 8-4.3. Capture The current images on the screen will be captured and saved in the Printed Files (Open Windows Explorer – click My Computer – click Program Files – click DvrMaster – click Printed Files). To play captured images, double-click one of JPEG Images in the Printed Files.
8. Remote Host Program 8-4.4. Status If the Status button on the DvrMaster is selected by clicking the mouse, the DvrMaster displays the DVR’s status related to connections of cameras, sensors, relay outputs and remaining HDD (Hard Disk Drive) capacity available for recording. Status button [Fig.
Stand-alone DVR Instruction Manual 8-4.5. Replay It is possible to replay the recorded data from the DVR system by using the Replay button in Fig.8-10 in the Multi mode only (refer to section 8-4.9.2). - Click the Replay button as shown in Fig.8-10 to playback the recorded data from the DVR system, and then the Replay Time Setup Window will be displayed.
8. Remote Host Program ▫ Playback Control Playback Control Buttons [Fig 8-12. Playback control] Playback control buttons : Button for fast rewinding up to 128 times by repeatedly pressing. : Button for viewing previous frame in still image. : Play button. : Button for viewing the next frame in still image. : Button for fast forwarding up to 128 times by repeatedly pressing. : It stops replaying.
Stand-alone DVR Instruction Manual 8-4.6. COPY It is possible to copy the recorded data from the DVR system to a client PC by using the Copy button in Fig.8-13 in the Multi mode only (refer to section 8-4.9.2). - Click the Copy button as shown in Fig.8-13 to copy the recorded data from the DVR system to a PC, and then the Copy Time Setup Window will be displayed.
8. Remote Host Program “ALL” in yellow represents that all the cameras are selected. The camera channel number(s) in yellow represents that the corresponding channel(s) are selected. - Click the Copy ( ) button and then the copying progressive bar as shown Fig.8-15 will show up. - While copying, click the Stop button in the Copy Time Setup Window if you want to stop copying. - To playback, refer to section 8-5.PLAYER. [Fig.
Stand-alone DVR Instruction Manual 8-4.7. Switch the Normal Screen to Full Screen ▫ Click the “FULL SCREEN” button on the DvrMaster as shown Fig.8-16 and then the current screen size will be enlarged to fit the monitor’s screen size, but the resolution will be lowered. ▫ Click the “FULL SCREEN” button again to go back to the NORMAL SCREEN. [Fig.
8. Remote Host Program 8-4.8. Speaker / Microphone ① ② ③ ④ ⑤ [Fig.8-18 Speaker / Microphone] Buttons of Remote Host Program ① Audio Input channel selection: Select the same audio channel as the DVR has. ② PC Speaker ON/OFF: Turn the Speaker ON or OFF by clicking the mouse. ③ PC Microphone ON/OFF: Turn the Microphone ON or OFF by clicking the mouse. ④ PC Speaker Volume Control: Adjust the Speaker Volume by clicking the amount of audio volume. It is available when the Speaker is turned ON.
Stand-alone DVR Instruction Manual 8-4.9. Connection mode There are two kinds of connection mode (See Fig.8-19) on the DvrMaster. Select one of them by clicking the mouse depending on your application. Connection mode [Fig.8-19 Connection Mode] 8-4.9.1. Terminal mode The functions of icons such as Recording, Play, Copy, Setup, System Status, Pan/Tilt, Display, Zoom and OSD on the bottom of the screen are identical to ones DVR system has. If the terminal mode button on the DvrMaster (See Fig.
8. Remote Host Program 8-4.9.2. Multi mode It is impossible to control (Recording on/off, Setup, System Status, Display and OSD) the DVR system in the Multi mode except Replaying and Copying (See section 8-4.5, 8-4.6 on page 144-146), but the image of channel 16 will always display on the monitor and the DvrMaster. - Click the Multi mode button to choose the Multi mode as shown in Fig.8-20. [Fig.
Stand-alone DVR Instruction Manual 8-4.10. Copy in the Terminal mode There are four icons such as NETWORK, USB, CD and DVD in the COPY menu of the Multi mode. The recorded data will be saved in the Backup Files (Open Windows Explorer – click My Computer - click the Program Files – click DvrMaster – click Backup Files) through the NETWORK, but the other icons such as USB, CD and DVD will only show what the DVR system functions on these icons.
8. Remote Host Program [Fig.8-22 Copying in the Terminal mode] [Fig.
Stand-alone DVR Instruction Manual 8-4.11 E-Map E-Map enables users to display the cameras on the digital map for better monitoring. The digital map should be a BMP file and you can make it (the higher resolution the better) or use the E-map samples saved in the E-map folder (See Fig.8-26). E-Map mode [Fig.8-24 E-Map MODE] 8-4.10.1. Addition of map - Click the E-Map button on the DvrMaster. - Right-click the MAP as shown in Fig.
8. Remote Host Program - To rename, right-click a saved eMap list and click “Rename” on the pop-up window as shown in Fig.8-27. - To delete, right-click a saved eMap list and click “Delete eMap” on the pop-up window as shown in Fig.8-28. - To display, double-click one of saved eMap lists. The image size of each channel will be minimized or maximized as much as you want. Note : The eMap list that is currently displaying can’t be deleted or renamed. [Fig.8-27 Rename] [Fig.8-28 Delete] 8-4.10.2.
Stand-alone DVR Instruction Manual 8-4.10.3. Usage of camera position The small squares with channel numbers on the map indicate the camera position. The blue screen represents that the corresponding camera is not connected to the DVR system. - Double-click the image to display a full screen. - To change the camera position, click the image and drag the mouse and drop on the map. - Double-click the channel number(s) to hide or show the image(s).
8. Remote Host Program 8-4.12 Pan / Tilt & Preset You can control the PTZ camera through DvrMaster. This feature is basically identical to what the DVR system has. Refer to section 6-7.7 PAN/TILT on page 46. CHANNEL SELECT PAN / TILT FOCUS ZOOM PRESET / RUN [Fig.
Stand-alone DVR Instruction Manual 8-5. PLAYER ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ [Fig.8-32 Player] Chart.
8. Remote Host Program ① Status window (Play mode, Date, Time) It indicates the play mode, date and time. [Fig.8-33 Status window] ② Calendar It shows the date currently being replayed. [Fig.8-34 Calendar] ③ Convert AVI File Convert the recorded files to AVI files. - Click the Convert AVI button on the Player and the Convert AVI window will be displayed (See Fig.8-35). - Click on the SELECT button on the Convert AVI window and the Browse for Folder will be displayed (See Fig.8-36 and Fig.8-37).
Stand-alone DVR Instruction Manual [Fig.8-35 Convert AVI window] [Fig.8-36 Backup Files by Networking] [Fig.
8. Remote Host Program [Fig.8-38 Select one of the Channels] [Fig.8-39 Start Convert Button] How to play the AVI files By using Windows media player: - Click the OPEN button on the Convert AVI window and double click one of the AVI files to play. The AVI files will save in the AVI Files folder (Open Windows Explorer – click My Computer click the Program Files – click DvrMaster – double click one of the AVI Files).
Stand-alone DVR Instruction Manual ④ Search button for Replaying - Click the Search button on the Player and the Browse for Folder will be displayed. - Select the folder that contains the recorded data and click the OK button on the Browser for Folder. One channel or all the channels can be replayed depending on the selection.
8. Remote Host Program [Fig.8-40 Print command window] [Fig.8-41 Print image] ⑦ Division button Select one of the following divisions while replaying. Full Screen 4 Division Screen 9 Division Screen 16 Division Screen [Fig.8-42 Division button] ⑧ Playback (Replay) Speed Control Move the slider with the mouse to control the replaying speed. The “0” represents the normal speed, “-“and “+” represents slow speed and fast speed respectively. [Fig.
Stand-alone DVR Instruction Manual ⑨ Search slider for replaying The slider can be moved left and right by clicking the slider on the bar and dragging it or just click the bar to search the recorded data. [Fig.8-44 Replay Search Slider] ⑩ Replay Control Refer to section 6-9.2.3. PLAY PREV REW NEXT FF STOP [Fig.8-45 Replay Control buttons] ⑪ Volume Control. Control the volume when replaying on the full screen mode [Fig.
9 9.Installation of additional HDDs CONTENTS 9-1. HDD (HARD DISK DRIVE) INSTALLATION.........................................................................166 9-2. INSTALLATION OF AN ADDITIONAL HDD ................................................................................
Stand-alone DVR Instruction Manual 9-1. HDD (Hard Disk Drive) INSTALLATION ▶ Three of internal Hard Disk Drives (HDD) and a CD R/W or DVD R/W can be installed in the system. DVR manufacturer already installed a 500GB of Hard Disk Drive (IDE) and a DVD R/W. To install additional hard disk drives, refer to the following pages. Note: Jumper settings for all the Hard Disk Drives and the DVD R/W should be made on “Cable Select”.
9. Installation of additional HDDs 9-2. Installation of an additional HDD ▶ Set the jumper setting to “Cable Select” position on the additional HDD. Note: Be sure that the jumper setting is correct. If not, the system will not recognize the additional HDD. ▶ Turn off the power. Unscrew and remove the cover. ▶ Install the additional HDD in the space as shown in Fig.9-1. ▶ Connect the power connector and the flat cable to the HDD. ▶ Reassemble the cover.
Stand-alone DVR Instruction Manual 168
APPENDIX CONTENTS RECORDING TIME TABLE ............................................................................................................170 FACTORY DEFAULT SETTINGS .....................................................................................................
Stand-alone DVR Instruction Manual Recording time table HDD: 500GB, Based on 16 cameras Recording Resolution : CIF(320 X 240) DAYS Each CH 30 fps 15 fps 10 fps 7.5 fps 5 fps 3 fps 2 fps 1 fps (16CH/fps) (480fps) (240fps) (160fps) (120fps) (80fps) (48fps) (32fps) (16fps) BEST 12.14 24.28 36.42 48.56 72.84 121.40 182.10 364.20 HIGH 18.83 37.66 56.49 75.32 112.98 188.30 282.45 564.90 NORMAL 25.25 50.50 75.75 101.00 151.50 252.50 378.75 757.50 LOW 33.17 66.
Factory default settings (1) LIVE SCREEN 16 SPLIT OSD ON (2) TIME / DATE DISPLAY: ON TIME FORMAT: 24 HOUR DATE FORMAT: MM/DD/YYYY (3) LOAD / BACKUP CONFIG NONE LISTS (4) USER ACCOUNT PASSWORD: SET YOUR PASSWORD (THE PASSWORD IS NULL) PASSWORD ON/OFF: OFF (5) IR REMOTE ID OFF (6) HDD OVERWRITE ON (7) CAMERA ACTIVE: ALL ON NAME: CAM XX BUZZER: ALL ON RELAY: ALL OFF PAN/TILT VENDOR: PELCO DISPLAY: ON SEQ DISPLAY DWELL: 1 SEC 171
Stand-alone DVR Instruction Manual (8) AUDIO (9) RECORD RECORD ICON DISPLAY: ON SIZE: ALL HALF D1 (704 X 240) FPS: ALL 15 fps QUALITY: ALL HIGH MODE: ALL MANUAL RECORD MODES SENSITIVITY: HIGH - TIMER RECORD ACTIVE: ALL OFF TIMER: ALL 00: 00 – 24: 00 - MOTION DETECT: OFF PRE: 1 sec. HOLD: 10 sec. SPOT: OFF REGION: ALL SET - SENSOR DETECT: OFF PRE: 1 sec. HOLD: 10 sec.
(10) NETWORK TYPE: DYNAMIC PORT: 5800 MNS: DISABLE SERVER 1 MODE: DISABLE SERVER 1 IP ADDRESS: 65.60.84.15 SERVER 1 PORT: 300 SERVER 2 MODE: DISABLE SERVER 2 IP ADDRESS: 221.149.149.117 SERVER 2 PORT: 300 SERVER SITE NAME: SXXXXXX (MAC ADDRESS) DDNS: DISABLE SERVER: DISABLE EMAIL: DISABLE EMAIL ADDRESS: ALL UNDEFINED EVENT: ALL DESELECT INTERVAL TIME: 5 MIN (11) VIDEO - CAMERA INPUT BRIGHTNESS: 128 (Max. 255) CONTRAST : 128 (Max. 255) - VGA OUTPUT BRIGHTNESS: 20 (Max. 40) CONTRAST : 20 (Max.
Stand-alone DVR Instruction Manual 174
FAQ CONTENTS I CAN NOT LOGIN.......................................................................................................................
Stand-alone DVR Instruction Manual I can not login ▶ Please check if the link LED of DVR and LAN port of PC are lit. ▶ Please check if the IP address on DVR and the PC is identical. Check SYSTEM STATUS by pressing STATUS button of DVR MY IP: xxx.xxx.xxx.xxx Check Target IP Address by clicking CONF button of PC host program. TARGET IP ADDRESS: xxx.xxx.xxx.xxx ▶ Please check whether there is a response upon PING test with DVR IP. Type "PING -t xxx.xxx.xxx.xxx" in DOS COMMAND window and execute. (xxx.xxx.
Limited 2Year Warranty This warranty gives the original purchaser specific legal rights and you may also have other rights, which may vary from state to state. If our products do not function because of any defect in material or workmanship, we will repair it for free for 2 year on parts and labor from the date of original purchase.
Stand-alone DVR Instruction Manual How to obtain Factory Service • Original purchaser must fill out the warranty card and mail it to the factory with the model number, serial number and the date of purchase. • We will repair or replace, and return the system to the owner under this limited warranty. • Please pack the system carefully and securely using the original packing materials, and send it prepaid and insured to: 13073 E. 166th St, Cerritos, CA 90703. • Please include a check for $40.
