Installation Instructions

Line
Neutral
Ground
Load
Black
White
Red
Green
Brown
● Connect the green power cord with the ground power cord of wall box,tighten
with P3 wire nut.
● Connect the black power cord with the line power cord of the wall box,tighten
with P3 wire nut.
● Connect the white line on the dimmer with the zero line,tighten with P3 wire
nut.
● Connect the red power cord with the neutral power cord of the wall box,tighten
withP3 wire nut.
● Screw the remaining brown wire on the dimmer with P3 wire nut for
protection .
Step 4b 3-Way
Connection way 1
Line
(Black)
Neutral
(White)
3-Way
Switch
Green
Red
Black
Brown
P
L
LD
N
Connecon way 1
Line (Black)
Neutral (White)
3-Way
Switc h
Green
Red
Black
Brown
P
L
LD
N
Line
Neutral
Ground
Load
Traveler
Black
White
Red
Green
Brown
● Connect the green power cord with the ground power cord of wall box,tighten
with P3 wire nut.
● Connect the black power cord with the line power cord of the wall box,tighten
with P3 wire nut.
● Connect the red power cord with the load power cord of the wall box ,tighten
with P3 wire nut.
● Connect the white power cord with the neutral power cord of the wall
box ,tighten with P3 wire nut.
● Connect the brown power cord with the traveler power cord of the wall
box,tighten with P3 wire
nut
Steop 5 Installing dimmer
● Carefully position all wires inside the wall-box, leaving enough space to insert
the dimmer and tighten with the matched screws.
Step 6
Step 6a Separated plate
● Installing the panel base on the dimmer and tighten with the matched
screws.
● Put the panel and panel base together, press gently to make sure it is be
installed firmly.
Function
Dimmer
Operation Way
Dimmer
Operation
Power-off
Operation
APP
Operation
Distribution
network mode
Continuous short
press power button5
times
× × ×
ON/OFF
Short press the
power button once
√ √ √
Time switch
on/off
NOT × × √
Dimming
Short or long press
the power button
UP/DOWN
√ × √
Quickly turn to
th
e maximum
brightest
Continuous short
press the dimming
Button (UP) twice
√ × √
Quickly turn to
the minimum
Continuous short
press the dimming
√ × √
brightest
Button (DOWN) twice
Setting the
maximum
brightness
Short press
maximum brightness
button
√ ×
√
Continuous short
press the power
button eight times
Setting the
minimum
brightness
Short press minimum
brightness button
√ ×
√
Continuous short
press the power
button six times
Restore
factory
Settings
Continuous short
press the power
button ten times
√ × ×
Shared device
-
×
×
√
group control
-
×
×
√
Wall box
Dimmer
Panel base
Priority
● On line operation can stop the mobile App operation; when on line operating,
App can’t operate.
Troubleshoong
Problems
Possible Cause
Solution
Lights flickering
Lamp has a bad
connection.
Reconnect and fix the
wires.
One dimmer been
connected to multiple
types bulbs, incur
interference and cause
flicker.
Change bulbs to same
type.
Abnormal
Put the power cut-off
button out and cut off
the power,
then put the power
cut-off button in and
connect the power on
again.
LED and CFL
flickers at low end of
dimming range.
Load compatibility is not
good.
Turn up lamp minimum
brightness properly.
Lamps can’t
be turn on
Circuit breaker has
tripped.
Turn power on
Fuse burn out
Change fuse
Lamp burned out
Change lamp
Lamp neutral connection
is not wired
Reconnect the lamp
neutral
Lights out of control
or unable to
connect to the
network
abnormal
Pull out the power
cut-off switch and
disconnect the power
supply; Insert the power
cut-off switch and turn
on the power again;
Panel base
Panel
Step 6b One-piece panel
● Place the panel on the installed dimmer and fix it firmly with
the matching mounting screws.
Function instruction
Table 1 Single -Pole Function table
Function Dimmer Operation Way
Dimmer
Operation
APP
Operation
Distribution
network mode
Continuous short press
power button
5 times
× ×
ON/OFF
Short press the power
button once
√ √
Time switch on/off NOT ×
√
Dimming
Short or long press the
power button UP/DOWN
√ √
Quickly turn to the
maximum brightest
Co
ntinuous short press the
dimming Button (UP) twice
√ √
Quickly turn to
the minimum
brightest
Continuous short press the
dimming Button (DOWN)
twice
√ √
Setting the
maximum
brightness
Short press maximum
brightness button
√ √
Continuous short press the
power button eight times
Setting the
minimum
brightness
Short press minimum
brightness button
√ √
Continuous short press the
power button six times
Restore factory
Settings
Continuous short press the
power button ten times
√ ×
Shared device
NOT
×
√
group control
NOT
×
√
Table2 3-way Function table
Using instruction
Short press: within 0.5 second
Long press: more than 0.5 second
Continuous short press:The interval between two short presses is less than
0.3 second
Dimmer
Panel