Installation Instructions

Works with DIMMABLE LED ,CFL,
Incandescent and halogen bulbs
Model No. DNA042DU2-W-600-P
120V
Rated Frequency 60Hz
Rated Wattage 600W
Load Range
Incandescent:15W-600W
LED/CFL:3W-200W
Dimming method Phase-cut
WARNINGS AND CAUTIONS
1. Risk of fire and electrical shock, the dimmer should be installed in
accordance with appropriate electrical codes and regulations.
2. This product should be use together with an upstream air-switch.
3. Turn power off at circuit breaker or fuse and test that power is off before
installing.
4. After install the dimmer, it is recommended to set the minimum brightness
level to make bulbs turn on immediately.
5. If you are unsure about any part
of these instructions, consult a licensed
elect
rician.
6. To reduce the risk of overheating and possible damage to other equipment,
do not install to control a receptacle, a motor-operated appliance or a
transformer-supplied appliance.
7.
Us
e w
ith compatible dimmable LED, CFL bulbs, Incandescent or halogen
bulbs only.
8. When multiple bulbs are used with one dimmer DO NOT mix bulb types. All
bulbs shall be either LED,CFL or incandescent. Using the same model of
each bulb will enhance dimmer performance.
Working
Environment
Temperature： 0℃ - 40℃
105 mm×44 mm×31mm (L×W×H)Model Size
Humidity：10% R.H. - 90% R.H
FCC Information
● This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Note1: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to prov
ide reasonable protection against harmful interference in a
resi
dential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can b
e determined by turning the equipment off and on, the user is encouraged to
tr
y to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
Note2: Any changes or modifications to this unit not expressly
approved by the
manufacture could void the user's authority to operate the equipment.
RF EXPOSURE STATEMENT
● This equipment complies with the FCC RF radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and any part
of your body.
FCC CAUTION
● Any changes or modifications to this unit not expressly approved by the
manufacture could void the user's authority to operate the equipment.
Functional parts instructions
Status Indicator
● Indicator lights red: OFF status.
●
●
Indicator lights green: ON status.
Green light flashing: enter distribution network mode.
Short press: Within 0.5s .
Long press: Over 0.5s.
Continuous short press: Each interval of short press should within 0.3s.
Minimum
Maximum
Maximum Brightness Button
● Setting the maximum brightness: There are six maximum brightness levels,
short press the button of maximum brightness once can change a maximum
brightness level.
Minimum Brightness Button
● Setting the minimum brightness: There are six minimum brightness levels,
short press the button of minimum brightness once can change a minimum
brightness level.
● Turn on: Short press once when in OFF.
● Turn off: Short press once when in ON.
● distribution network mode: when the light is on, press the on key for 5 times
continuously. After the status indicator flashes (once in 2 seconds), the mobile
phone can connect the dimmer. After the distribution network is su
ccessful,
(if not connected, exit the distribution network mode after 3 minutes).
● Short press the power button six times to set the ideal minimum brightness
when in ON status.
● Short press the power button eight times to set the ideal maximum brightness
when in ON status.
● Continuous short press ten times and the status indicator flash three times to
restore the factory default settings when in the maximum brightness st
atus.
Dimming Button (UP)
● Short press the dimming button once can increase a level of brightness
when in ON status.
●
Long press the dimming button can continuous to increase the brightness
until release or reach the maximum brightness.
● Continuous short press two times when in ON/OFF status to turn quickly to
the maximum brightness.
Dimming Button (Down)
● Short press the dimming button once can decrease a level of brightness
when in ON status.
● Long press the dimming button can continuous to decrease the brightness
until release or reach the minimum brightness.
● Continuous short press two times when in ON/OFF
status to turn quickly
to the minimum brightness.
Power Cut -off Button
● Put in the power cut-off button to connect the power.
● Put out the power cut-off button to cut off the power.
Switch Operation
● Turn on: Switch on when the light is off.
● Turn off: Switch on when the light is on.
● Luminance Indicator Table
Item
Luminance Level
Luminance Indicator
1
Luminance Level 1-5
LED 1 normally on
2
Luminance Level 6-10
LED 1 LED 2 normally on
3
Luminance Level 11-15
LED 1 LED 3 normally on
4
Luminance Level 16-20
LED 1 LED 4 normally on
5
Luminance Level 21-25
LED 1 LED 5 normally on
6
Luminance Level 26-30
LED 1 LED 6 normally on
7
Luminance Level 31-35
LED 1 LED 7 normally on
8
Luminance Level 36-40
LED 1 LED 8 normally on
Power Button
Luminance Indicator
LED1
LED2
LED3
LED4
LED5
LED6
LED7
LED8
Luminance
Tools need to install the dimmer
Installation
Step 1 WARNING: To avoid fire and electrical shock, TURN PFF POWER at circuit
breaker or fuse and test that power is off before wiring.
Step 2 Remove the screws installed on the existing panel and switch, carefully pull
out the switch from the wall box, identify and remove the power cord attached to
the switch, and the switch, do not remove the power cord detached from the
switch. (This step is not required for new configuration installation.)
Step 3 Identify the power cord type
Note: If the power cord in the wall box is different from the
following layouts, please consult an electrician.
IMPORTAN
T: For 3-Way applications,note that one of the screw terminals from the
old switch being removed will usually be a different (Black)or labeled Common
(Line or Load)in both the dimmer wall box and 3-way wall box.
Step 4 Typical wiring application
Step 4a Single-Pole
Line(Black)
Neutral(White)
Green
Red
Black
Brown
P
L
LD
N
5mm Philips Screwdriver
Test Pencil
Electrical Tape
Plier
Cutter
Ruler
Single-Pole
Line (Hot)
Neutral
Ground
Load
3-Way
Line or Load
(See note below)
Neutral
Ground
Load
Traveler
Parts Information
Mounting
Frame（1 pc）
Face plate
（1 pc）
Note:
● When enter into distribution network mode, turn on the wifi and
Bluetooth of the mobile phone at the same time, so that the
distribution network mode can be configured quickly.
● In case of wi-fi disconnection, under the condition of normal
wireless Internet access of the mobile phone, turn on the
bluetooth of the mobile phone, and after 5min, the mobile phone
APP can control the dimmer.
Dimming Buon
(UP)
Luminance
Indicator
(Down)