Instructions / Assembly

12
NOTE: For Non-Insulated Steel Carriage House Doors and
Non-Insulated Composite Doors, see handle installation template that
comes with door.
Step 8B-1:
■
Use supplemental templates provided in handle bag to determine handle
configuration for your door size.
Step 8B-2:
■
Find the center of the distance between embosses on the front of the
section.
■
Use template included with handle to to line up the center lines and the
bottom section.
■
Drill two 1/2" holes where indicated through the front skin of the section
and insulation, but STOP BEFORE drilling through the back skin.
Step 8B-3:
■
Flip section over and drill two 5/16" holes, through the back skin.
Step 8B-4:
■
Slide the black head 1/4" carriage bolt through horizontal spade handle,
handle spacer, front of the section, back of the section and roll grip
handle.
■
Secure with 1/4" flange nut (Fig. 8B-A).
■
Repeat Steps 8-2 through 8-4 for second bottom handle
(if applicable).
■
Second section (to be installed at completion of STEP 9A-4.
Not required on doors with outside keyed lock).
Step 8B-5:
■
Use back of the template to find your door configuration.
■
Using the template, drill the holes in your second section.
Step 8B-6:
■
Find the center of the distance between embosses and the middle of the
section height on the front of the section.
■
Use template included with handle to line up the center lines and the
bottom section.
■
Drill the indicated 1/2" holes through the section and insulation.
Step 8B-7: Two Outside Spade Handles
For one handle, skip to STEP 8B-8.
■
Line up holes in handle backer plate with holes drilled in previous step.
■
Attach handle backer plate to back of door with (2) #14 × 5/8" sheet
metal screws through inside roll grip handle and into the inside skin
(Fig. 8B-A).
■
Slide two 1/4" black head carriage bolts through the vertical spade
handle, the handle spacers, door section and through the backer plate.
■
Secure on the inside with 1/4" flange nuts. Do this for each handle
(Fig. 8B-A) Skip to STEP 8-9.
Step 8B-8: One Outside Spade Handle
■
Slide (2) 1/4" black head carriage bolts through vertical handle, handle
spacers, door section and through backer plate.
■
The top carriage bolt should also go through the top hole of the roll grip
handle.
■
Attach bottom of roll grip handle with a #14 × 5/8" sheet metal screw
into the backer plate (Fig. 8B-A).
Step 8B-9:
■
Repeat STEP 8B-6 through 8B-8 for second handle set (if applicable).
STEP 8 - INSTALL LIFT HANDLES
STEP 8B: FOR NON-INSULATED STEEL CARRIAGE HOUSE DOORS &
NON-INSULATED COMPOSITE DOORS
Fig. 8B-A
9
8
7
6
7
8
5
4
3
2
1
1
2
3
8
6
5
Item No. Description
1 1/4" x 2-1/2" Black Head Carriage Bolt
2 Black Vertical Spade Handle
3 1/2" OD x 2" Long Handle Spacer
4 Handle Backer Plate
5 1/4-20 Serrated Flange Nut
6 #14 x 3/4" Hex Head Self-Tapping Screw
7 #14 x 3/4" Hex Head Sheet Metal Screw
8 Roll Grip Handle
9 Black Horizontal Spade Handle
9
8
7
6
7
8
5
4
3
2
1
1
2
3
8
6
5
Item No. Description
1 1/4" x 2-1/2" Black Head Carriage Bolt
2 Black Vertical Spade Handle
3 1/2" OD x 2" Long Handle Spacer
4 Handle Backer Plate
5 1/4-20 Serrated Flange Nut
6 #14 x 3/4" Hex Head Self-Tapping Screw
7 #14 x 3/4" Hex Head Sheet Metal Screw
8 Roll Grip Handle
9 Black Horizontal Spade Handle