DALI Gateway 5502DAL Programming Guide REGIST 23446_F2255-01 5502DAL C-Bus DALI Gateway APPROVED.
5502DAL C-Bus DALI Gateway Programming Guide Contents 1.0 Introduction .............................................................................................................3 1.1 Description .........................................................................................................3 1.2 Definitions...........................................................................................................4 2.0 Concepts .................................................................
5502DAL C-Bus DALI Gateway Programming Guide 1.0 Introduction This Programming Guide provides basic set-up information for the C-Bus DALI Gateway. For additional information refer to C-Bus Toolkit software Help. Installers should contact the supplier of the Digital Addressable Lighting Interface (DALI) equipment to obtain the programming and commissioning software for DALI devices. 1.1 Description The DIN rail mounted unit is normally installed inside an enclosure.
5502DAL C-Bus DALI Gateway Programming Guide 1.2 Definitions The following definitions are useful in discussing the DALI Gateway: Term Definition C-Bus Load Any device connected to an electric circuit that consumes power controlled by a C-Bus Output Unit (examples are lights and electric motors). C-Bus Output Unit A device, such as a relay or dimmer, that directly controls electric loads.
502DAL C-Bus DALI Gateway Programming Guide 2.0 Concepts The C-Bus and DALI systems share many similar concepts. This similarity provides a basis for interconnecting the two systems. Before exploring the mapping between the two systems, it is worth summarising the basic concepts in the two systems. 2.1 C-Bus C-Bus is a microprocessor-controlled network system that uses Unshielded Twisted Pair cable (UTP, Category 5e).
5502DAL C-Bus DALI Gateway Programming Guide Group Addresses Within the lighting applications, group addresses are used to emulate the function of conventional wiring. The C-Bus addressing scheme allows you to have up to 255 groups. Each group is like a lighting circuit and can be controlled separately from any other group. A group association is programmed into both input units (key inputs and sensors) and output units (relays and dimmers).
5502DAL C-Bus DALI Gateway Programming Guide 2.3 C-Bus to DALI Address Mapping A user-configurable table in the Toolkit GUI maps the addresses used by C-Bus and those by the DALI system. Refer to Toolkit Help for assistance in mapping C-Bus to DALI. 3.0 Wiring Notes CAUTION Do not tie the outputs of the DALI power supplies together. Damage to the supplies and the Gateway unit will occur. Do not connect the DALI Gateway to mains power. The unit is powered from the C-Bus network.
5502DAL C-Bus DALI Gateway Programming Guide Two RJ45 connectors are provided for upstream and downstream network attachment. The C-Bus network uses pink Cat 5e, polarised 15-36 volt, twisted-pair cable, catalogue number 5005C305B (solid) and 5005C305BST (stranded).
5502DAL C-Bus DALI Gateway Programming Guide 4.0 Messages When a C-Bus command is sent on the C-Bus network to turn off a mapped group address this message will be transmitted by the DALI Gateway to the appropriate load on the DALI network. The converse is also true; a message on the DALI network can be translated and transmitted on the C-Bus network. For example, if a key input unit is programmed to toggle Group Address $42 (66), then DALI_1_GROUP2 will respond.
5502DAL C-Bus DALI Gateway Programming Guide 5.2 C-Bus Setup Program the C-Bus DALI Gateway using C-Bus Toolkit software that can be downloaded free of charge from the Internet. To determine the C-Bus group addresses, refer to the DALI programming table.
5502DAL C-Bus DALI Gateway Programming Guide 7.0 Specifications Parameter Value C-Bus input voltage 15-36V d.c. Current drawn 32mA from the C-Bus network. The gateway does not provide power to the network. C-Bus AC input impedance 50kΩ at 1kHz Electrical isolation 3.75kV RMS for one minute between C-Bus and the DALI networks Maximum number of units on a single C-Bus network 50 units Connections C-Bus: 2 – RJ45 connectors DALI: 2 screw terminals per DALI network Mounting type DIN rail Max.
5502DAL C-Bus DALI Gateway Programming Guide 8.0 Standards Complied The 5502DAL C-Bus DALI Gateway meets the following standards.
5502DAL C-Bus DALI Gateway Programming Guide 9.0 Two Year Warranty The 5502DAL C-Bus DALI Gateway carries a two year warranty against manufacturing defects. Warranty Statement The benefits conferred herein are in addition to, and in no way shall be deemed to derogate, either expressly or by implication, any or all other rights and remedies in respect to the Schneider Electric product, which the consumer has in the location where the product is sold.
5502DAL C-Bus DALI Gateway Programming Guide Notes 14 of 16 23446_F2255-01 5502DAL C-Bus DALI Gateway APPROVED.indd 14 © 2011 Schneider Electric. All Rights Reserved.
5502DAL C-Bus DALI Gateway © 2011 Schneider Electric. All Rights Reserved. 23446_F2255-01 5502DAL C-Bus DALI Gateway APPROVED.
Technical Support For further assistance in using this product, consult your nearest Clipsal Integrated Systems (CIS) Sales Representative or Technical Support Officer. Technical Support Contact Numbers Australia 1300 722 247 (CIS Technical Support Hotline) New Zealand 0800 888 219 (CIS Technical Support Hotline) Northern Asia +852 2484 4157 (Clipsal Hong Kong) South Africa 011 314 5200 (C-Bus Technical Support) Southern Asia +603 7665 3555 Ext.
