C-Touch Colour Touch Screen Installation Instructions 50xxCTC2 Series
Clipsal and C-Bus are registered trademarks of Clipsal Australia Pty Ltd ABN 27 007 873 529. © Copyright Clipsal Australia Pty Ltd 2008. All rights reserved. This material is copyright under Australian and international laws. Except as permitted under the relevant law, no part of this work may be reproduced by any process without prior written permission of and acknowledgement to Clipsal Australia Pty Ltd. The information in this manual is provided in good faith.
Contents 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 Product Range Important Notes Description 3.1 Packing List 3.2 Features 3.3 Infrared Remote Control Definitions Installation Procedure 5.1 Location 5.2 Multiple C-Touch Units Mounting Instructions 6.1 Plasterboard Bracket 6.2 Nail Bracket 6.3 Wall Box 6.4 The Power Supply Unit 6.5 Attaching the Facia Wiring Details 7.1 Rear Panel Connectors 7.2 C-Bus Network Connection 7.3 Programming Lead 7.
C-Touch Colour Touch Screen 4
Installation Instructions 1.
C-Touch Colour Touch Screen • • • • Changes or modifications not expressly approved by Clipsal Integrated Systems could void the user’s authority to operate the equipment (under FCC rules). To comply with EMC regulations the included ferrite filters must be fitted to any audio, video and IR cables connected to the C-Touch Colour unit. Refer to sections 7.3 and 7.4 on Pages 22 and 23.
Installation Instructions Figure 1 – Typical components packed with the5080CTC, GF C-Touch Colour 3.2 Features The C-Touch Colour’s features include: • • • • • • • • • a touch sensitive 6.4 inch (16.3 cm) LCD screen real time clock for automatic scheduling of events 10/100 Ethernet interface in-built infrared (IR) receiver with an external IR input 2 × USB and 1 × RS-232 serial ports a composite video output 2 × C-Bus connections (in parallel) audio line in and line out connections inbuilt speaker.
C-Touch Colour Touch Screen 3.3 Infrared Remote Control The C-Touch Colour is supplied with an Infrared Remote Control, which can be used to trigger scenes, switch loads, and adjust lighting levels. The remote control functionality is incorporated into a software project. The available functions depend on how the C-Touch Colour is programmed. If multiple C-Touch Colour units are installed, the same remote control can talk to each of them. Figure 2 – The Infrared Remote Control 4.
Installation Instructions 5.0 Installation Procedure 5.1 Location It is important to select the right location to install the C-Touch Colour. Some considerations: • The unit has a typical viewing angle of 70° to the left, right and down, and 40° up (illustrated in Figure 3). Take this into account when choosing the mounting height. • Provide easy access to the unit for switching lights and selecting scenes.
C-Touch Colour Touch Screen 40° up 70° left 70° down 70° right Figure 3 – Consider the C-Touch Colour's viewing angle when mounting the unit 5.2 Multiple C-Touch Units Multiple C-Touch units can be installed on a C-Bus network. These units may be programmed to operate cooperatively or independently of each other. Take care not to mount units where a single IR remote control transmission can be received by multiple units (illustrated in Figure 4).
Installation Instructions 6.0 Mounting Instructions There are three options for mounting the C-Touch Colour: • • • 6.1 in plasterboard walls using a plasterboard bracket in stud walls (such as timber frame internal walls) using a nail bracket in solid walls (such as brick or stone) or stud walls using a wall box. Plasterboard Bracket The 5000CTCRM C-Touch Colour Plasterboard Bracket provides a convenient means of mounting a 50xxCTC2 Series C-Touch Colour Touch Screen in a plasterboard wall.
C-Touch Colour Touch Screen Figure 6 - Installing the plasterboard bracket To install the plasterboard bracket: 1) Prepare a 208 × 162 mm cut-out in the plasterboard. 2) Place four 4 mm holes in the plaster board to provide clearance for the screws that secure the Colour Touch Screen. 3) Using the four short screws supplied, attach the side clamps to the bracket as illustrated. 4) Ensure the four screws securing the side clamps are loose, and the side clamps can move freely.
Installation Instructions 6.2 Nail Bracket The C-Touch Colour Nail Bracket (catalogue number 5000CTCNA) provides a convenient means of mounting the C-Touch Colour unit. The nail bracket (illustrated in Figure 7) is used where is it practical to nail or screw the bracket into a wall frame. Figure 7 – A C-Touch Colour Nail Bracket To mount the C-Touch Colour using the nail bracket: 1) Place the bracket against a beam of the wall frame. 2) Nail the bracket into the frame.
C-Touch Colour Touch Screen Cable Connection Quantity C-Bus RJ45 2 Serial RS-232 DB9 1 Infrared (input) 3.5 mm mono socket 1 Audio line in 3.5 mm stereo socket 1 Audio line out 3.
Installation Instructions Figure 8 – Installing the C-Touch Colour Nail Bracket 15
C-Touch Colour Touch Screen 6.3 Wall Box The C-Touch Colour Wall Box (catalogue number 5000CTCWB) allows the C-Touch Colour unit to be mounted within a solid wall construction such as brick or stone. It provides increased RF shielding compared to the Nail Bracket. The wall box (illustrated in Figure 9) may also be used to mount a C-Touch Colour unit in timber or metal framed stud walls.
Installation Instructions Figure 10 – Installing the C-Touch Colour Wall Box 6.4 The Power Supply Unit It is recommended that the 5000CTCPS/2 Power Supply be mounted above the C-Touch Colour unit in the ceiling space. Note the following important points: • • • • Allow adequate ventilation. Do not cover the Power Supply unit or sandwich it between cavities or insulation. Feed the DC output cable to the C-Touch Colour unit through conduit.
C-Touch Colour Touch Screen 6.5 Attaching the Facia The following steps are illustrated in Figure 11. To attach the facia: 1) Position the facia over the touch screen, with the IR and indicator windows on the right hand side. Ensure that the clips on the left underside of the facia are positioned just left of the matching clips on the C-Touch Colour unit. 2) While applying forward pressure on the left side of the facia (toward the touch screen), push the left side to the right.
Installation Instructions To remove the facia: 1) Grasp the right side of the facia with your left hand. 2) Push the release lock in with your right thumb. At the same time lift the right side of the facia plate off and to the right with your left hand (to disengage the clip). 3) Swing the facia off towards the left. Refer to Figure 12.
C-Touch Colour Touch Screen 7.0 Wiring Details 7.1 Rear Panel Connectors Compact Flash card (factory fitted) Ethernet C-Bus C-Touch Colour - 5000CTC Series C-Bus Voltage: 15 – 36Vdc C-Bus Current: 22mA DC Input: 5.3Vdc, 5A Tested To Comply With FCC Standards UNIT ADDRESS: FOR HOME OR OFFICE USE REGISTERED PATENT WARNING: This unit must be used with CLIPSAL C-Bus system only. Made in Australia MOD.
Installation Instructions C-Bus Positive: blue + orange C-Bus Negative: blue & white + orange & white Remote OFF: brown + brown & white Remote ON: green + green & white Figure 14 – C-Bus cable conductor assignments Pin C-Bus Connection Colour 1 Remote ON green & white 2 Remote ON green 3 C-Bus Negative (-) orange & white 4 C-Bus Positive (+) blue 5 C-Bus Negative (-) blue & white 6 C-Bus Positive (+) orange 7 Remote OFF brown & white 8 Remote OFF brown 87654321 87654321
C-Touch Colour Touch Screen 7.3 Programming Lead A programming lead is provided with the C-Touch Colour unit. It consists of a Cat-5 crossover Ethernet patch cable. Use the crossover programming lead when connecting directly from a PC (e.g. laptop) to the C-Touch Colour. If connecting through a network hub or switch, you will need to use a standard Ethernet cable. Cable conductor assignments for a crossover Ethernet cable are shown in Table 3.
Installation Instructions Figure 15 – Audio and IR cables must be looped through the large ferrite filter 7.5 Video Connection An RCA video out connection is provided on the bottom right side of the C-Touch Colour (looking from the front). This allows the unit’s display to be viewed on a TV or monitor which has a composite video input. If the video out connection is utilised, it is important that the smaller ferrite filter (provided) is fitted over the video cable.
C-Touch Colour Touch Screen 7.6 RS-232 Connection The RS-232 serial port connection uses standard EIA 574 pinouts (provided in Table 4). The RS-232 port allows you to connect external devices to the C-Touch Colour, such as security and control equipment. If using the RS-232 port to connect to external devices, ensure you use a suitable shielded data cable. Cable length should be limited to 15 metres for communication at up to 19,200 bps, or 7.5 metres at 38,400 bps.
Installation Instructions 8.0 C-Bus System Clock The C-Touch Colour incorporates a software selectable C-Bus System Clock used for synchronising data communication on a C-Bus network. Since a maximum of three enabled System Clock units should exist on a network, the System Clock on the C-Touch Colour is disabled by default. 9.0 C-Bus Power Requirements The C-Touch Colour draws 20 mA from the C-Bus network. Adequate C-Bus power supply units must be installed to support connected devices.
C-Touch Colour Touch Screen 12.0 Programming Requirements Unit Address The C-Touch Colour must be programmed with a unique identification address (Unit Address). This is accomplished using the C-Bus Toolkit software, available from the Downloads section of the Clipsal Integrated Systems (CIS) web site (http://www.clipsal.com/cis). C-Bus Toolkit is also used to enable the C-Bus System Clock and burden if required.
Installation Instructions 13.0 Using the C-Touch Colour Transfer Utility The C-Touch Colour Transfer Utility is used to transfer a software project to the C-Touch Colour. It is included with the PICED software, which is available from the Downloads section of the CIS web site (http://www.clipsal.com/cis). This section takes you through the process of installing a project onto the C-Touch Colour, using a direct Ethernet connection.
C-Touch Colour Touch Screen 2) Remove the facia if it has been fitted to the unit (refer to Page 19). 3) Plug the supplied programming lead (red crossover cable) into the RJ45 Ethernet socket on the front right side of the unit. 4) Ensure your PC is switched on, and plug the other end of the crossover cable into the Ethernet socket on your PC. 5) Wait approximately 3 minutes to enable the network connection to establish (DHCP). You can skip this step if your PC has a static IP address.
Installation Instructions 9) You will be asked to select the type of network (Figure 19). Select Standalone, then click Next. Figure 19 – Select the network connection type 10) The Transfer Utility software will suggest an IP Address to be programmed into the C-Touch Colour unit (Figure 20). This address is chosen to be compatible with the PC you are using. It is sent to the C-Touch Colour which will ask you to confirm the new IP Address (Figure 21). Press Yes on the C-Touch Colour unit.
C-Touch Colour Touch Screen Figure 21 – Press Yes on the C-Touch Colour to confirm the IP Address 11) The C-Touch Colour will advise you that the Address Type has been set (Figure 22). Press OK on the C-Touch Colour to clear this message. Figure 22 – The Address Type has been set 12) Click Next on your PC. The Transfer Utility software will again search for the C-Touch Colour unit.
Installation Instructions 13) You will be presented with a list containing the found unit (Figure 23). Ensure the unit is selected (click on its name to highlight it), then click Finish. Figure 23 – Select the unit you want to program, then click Finish 14) The Transfer Utility software will display the Information page for the connected C-Touch Colour unit (Figure 24). Two other pages, Control and Transfer, can be selected by clicking the appropriate tab.
C-Touch Colour Touch Screen 15) Click the Transfer tab to select the Transfer page shown in Figure 25. From here you can transfer a project to the C-Touch Colour unit. You can also transfer a project or log file from the C-Touch Colour to your PC, or update the unit with new system software (if provided).
Installation Instructions 16) Select the ‘…’ button adjacent to the Project File Location field (Figure 26), and choose the project archive to be transferred. Figure 26 – Choose a project to be transferred to the C-Touch Colour 17) Click the “Transfer Project To C-Touch Colour” button (Figure 27). Figure 27 – Transfer the project to the C-Touch Colour 18) Depending on its size, the project may take from one to many seconds to transfer.
C-Touch Colour Touch Screen 19) Click the Control tab to select the Control page shown in Figure 29. From here you can stop and start the C-Touch Colour’s project (in HomeGate), enable logging, set the time and change the name that identifies the C-Touch Colour over an Ethernet connection. Figure 29 – The Control page in the Transfer Utility software 20) Ensure that the time on your PC is set correctly. If not, change the time.
Installation Instructions Using the C-Touch Colour on a network follows the same principles. You may need assistance from the network administrator. 13.1 The Reset Button In the event that the C-Touch Colour software becomes unresponsive, you can restart the unit by pressing the reset button. The reset button is located to the right of the display, beneath the facia (as shown in Figure 31). Instructions on removing the facia are provided on Page 19 (Section 6.4).
C-Touch Colour Touch Screen 14.0 Electrical Specifications C-Touch Colour Touch Screen Parameter Description Supply voltage 5 V DC, 30 W maximum via power pack* Display type 6.4 inch (16.
Installation Instructions Infrared Remote Control Parameter Description Supply voltage 3 V DC required for normal operation.
C-Touch Colour Touch Screen 15.0 Mechanical Specifications C-Touch Colour Touch Screen Parameter Description Dimensions (W×H×D) 246 x 173 x 72.5 mm (excluding facia) Protrusion from wall 23.5 mm (including glass facia) Mounting depth (into wall) 54 mm Mounting centres (H×V) 212.5 × 112 mm Weight 1375 g (excluding facia) 246 mm 202 mm 18.
Installation Instructions Infrared Remote Control Parameter Description Dimensions (W×H×D) 86 × 54 × 8 mm Weight 28 g Colour black Plasterboard Bracket Parameter Description External dimensions (W×H×D) 261 × 200 × 44 mm Cut-out dimensions (W×H) 208 × 162 mm Required cavity clearance 310 × 310 × 65 mm Weight 296g Nail Bracket Parameter Description External dimensions (W×H×D) 287 × 215 × 47 mm Cut-out dimensions (W×H) 205 × 162 mm Weight 530 g Wall Box Parameter Description Extern
C-Touch Colour Touch Screen 16.0 Standards Complied DECLARATIONS OF CONFORMITY Australian/New Zealand EMC & Electrical Safety Frameworks and Standards The C-Touch Colour Touch Screen complies with the following: Regulations EMC (C-Tick) Safety Standard AS/NZS CISPR 22 (Class A) Title IT Equipment Emissions Standard AS/NZS CISPR 24 IT Equipment Immunity Standard AS/NZS 60950.1 IT Equipment Safety Standard WARNING: This is a Class A product.
Installation Instructions 17.0 Warranty The C-Touch Colour Touch Screen carries a two year warranty against manufacturing defects. Warranty Statement 1) The benefits conferred herein are in addition to, and in no way shall be deemed to derogate; either expressly or by implication, any or all other rights and remedies in respect to Clipsal Integrated Systems Product, which the consumer has under the Commonwealth Trade Practices Act or any other similar State or Territory Laws.
C-Touch Colour Touch Screen 42
Technical Support and Troubleshooting For further assistance in using this product, consult your nearest Clipsal Integrated Systems (CIS) Sales Representative or Technical Support Officer. Technical Support Contact Numbers Australia 1300 722 247 (CIS Technical Support Hotline) New Zealand 0800 888 219 (CIS Technical Support Hotline) Northern Asia 852 2484 4157 (Clipsal Hong Kong) South Africa (011) 314 5200 (C-Bus Technical Support) Southern Asia 603 7665 3555 Ext.
