C-Touch Colour Touchscreen 5000CTC2 Series Installation Instructions
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions Contents 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 Product Range.................................................................................................3 Important Notes...............................................................................................3 Description.......................................................................................................4 3.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 1.0 Product Range Several colour options are available. Contact you local sales representative for more information. Catalogue Number Description 5080CTC2-xx 6.4-inch Colour Touchscreen, wall mount, Saturn surround 5050CTC2-xx 6.4-inch Colour Touchscreen, wall mount, Neo surround BS5000CTC2 6.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 3.0 Description The C-Touch Colour touchscreen allows sophisticated control of an entire C-Bus system from one location. Using C-Bus Toolkit and PICED software, the unit can be configured to look and operate in a manner convenient to the user. 3.1 Packing List The items included in the C-Touch Colour Touchscreen’s package are as listed below. These items are subject to change.
000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 3.2 Features The C-Touch Colour’s features include: • Touch-sensitive 6.4 inch (16.3cm) LCD screen • Real-time clock for automatic scheduling of events • 10/100 Ethernet interface • In-built infrared (IR) receiver with and external IR input • 2 × USB and 1 × RS-232 serial ports • 2 × C-Bus connections (in parallel) • Audio Line In and Line Out connections • Inbuilt speaker.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 3.3 Infrared Remote Control The C-Touch touchscreen is supplied with an infrared remote control that can be used to trigger scenes, switch loads, and adjust lighting levels. the remote control functionality is incorporated into a software project. The available functions depend on how the touchscreen is programmed. If multiple C-Touch units are installed, the same remote control can talk to each of them. Figure 1.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 5.0 Installation Procedure 5.1 Location It is important to select the right location to install the touchscreen. Some considerations: • The unit has a typical viewing angle of 70° to the left, right and down, and 40° up (see Figure 2). Take this into account when choosing the mounting height. • Provide easy access to the unit for switching lights and selecting scenes.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 5.2 Multiple C-Touch Units Multiple C-Touch units can be installed on a C-Bus network. These units may be programmed to operate cooperatively or independently of each other. Take care not to mount units where a single IR remote control transmission can be received by multiple units (see Figure 3). Otherwise, multiple units may trigger a scene with unpredictable results.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 6.0 Mounting Instruction There are three options for mounting the touchscreen: • In plasterboard walls using a plasterboard bracket • In stud walls (such as timber frame internal walls) using a nail bracket or • In solid walls (such as brick or stone) or stud walls using a wall box. 6.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions Figure 5. Installing the plasterboard bracket. To install the plasterboard bracket: 1) Prepare a 208 × 162mm cut-out in the plasterboard. 2) Place four 4mm holes in the plaster board to provide clearance for the screws that secure the touchscreen. 3) Using the four short screws supplied, attach the side clamps to the bracket as illustrated.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 6.2 Nail Bracket The C-Touch Colour Nail Bracket, catalogue number 5000CTCNA, provides a convenient means of mounting the touchscreen. The nail bracket (shown in Figure 6) is used where it is practical to nail or screw the bracket to a wall frame. Figure 6. C-Touch Colour Nail Bracket. To mount the C-Touch Colour using the nail bracket: 1) Place the bracket against a beam of the wall frame. 2) Nail the bracket into the frame.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions Cable Connection Quantity C-Bus RJ45 2 Serial RS-232 DB9 1 Infrared (input) 3.5mm mono socket 1 Audio line in 3.5mm stereo socket 1 Audio line out 3.5mm stereo socket 1 Serial USB USB Type A 2 Ethernet LAN RJ45 DC power 7 pin DIN 1 PS/2 mouse or keyboard 6 pin mini DIN 1 Connector Location 2 (1 front, 1 back) Table 1.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions Figure 7.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 6.3 Wall Box The C-Touch Colour Wall Box, catalogue number 5000CTCWB, allows the touchscreen to be mounted in a solid wall construction such as brick or stone. It provides better RF shielding than the Nail Bracket. The wall box (see Figure 8) may also be used to mount the touchscreen in timber or metal-frame stud walls. Figure 8.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions Figure 9. Installing the C-Touch Colour Wall Box 6.4 Power Supply Unit It is recommended that the 5000CTCPS/2 Power Supply be mounted above the touchscreen in the ceiling space. Note the following important points: • Allow adequate ventilation. Do not cover the power supply unit or sandwich it between cavities or insulation. • Feed the d.c. output cable to the touchscreen through conduit.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 6.5 Attaching the Fascia The following steps are illustrated in Figure 10. To attach the fascia: 1) Position the fascia over the touchscreen, with the IR and indicator windows on the right hand side. Ensure that the clips on the left underside of the fascia are positioned slightly to the left of the matching clips on the touchscreen.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions To remove the fascia: 1) Grasp the right side of the fascia with your left hand. 2) Push the release lock in with your right thumb. At the same time lift the right side of the fascia plate off and to the right with your left hand (to disengage the clip). 3) Swing the fascia off towards the left. Refer to Figure 11. Push the release lock Lift off and to the right to disengage the clip, then swing to the left Figure 11.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 7.0 Wiring Details 7.1 Rear Panel Connectors Figure 12. Rear panel connector identification 7.2 C-Bus Network Connection Use one of the C-Bus RJ45 sockets to connect to the C-Bus network. Use Cat.5e Unshielded Twisted Pair (UTP) C-Bus cable, catalogue numbers are 5005C305B (solid) and 5005C305BST (stranded). Conductor assignments are provided in Figure 13 and Table 2. The C-Bus RJ45 sockets are internally connected together.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions C-Bus cable conductor assignments Pin C-Bus Connection Colour 1 Remote ON green & white 2 Remote ON green 3 C-Bus Negative (-) orange & white 4 C-Bus Positive (+) blue 5 C-Bus Negative (-) blue & white 6 C-Bus Positive (+) orange 7 Remote OFF brown & white 8 Remote OFF brown Table 2.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 7.3 Programming Lead A programming lead is provided with the C-Touch Colour unit. It consists of a Cat.5e crossover Ethernet patch cable. Use the crossover programming lead when connecting directly from a PC to the touchscreen. If connecting through a network hub or switch, you will need to use a standard Ethernet cable. Cable conductor assignments for a crossover Ethernet cable are shown in Table 3.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 7.4 Audio and IR Connections Audio line in and line out connections (3.5mm stereo sockets) are provided on the bottom left side of the touchscreen (looking from the front). An infrared input (3.5mm mono socket) is also provided at this location. If any of these connections are used, it is important that the cables are looped through the large ferrite filter provided.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 7.5 RS-232 Connection The RS-232 serial port connection uses standard EIA 574 pinouts (see Table 4). The RS-232 port allows you to connect external devices to the touchscreen, such as security and control equipment. NOTE If using the RS-232 port to connect to external devices, be sure to use a suitable shielded data cable. The cable length should be limited to 15 metres for communication up to 19,200 bps, or 7.5 metres at 38,400 bps.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 8.0 Megger Testing Important points when megger testing an electrical installation: • Only megger test when mains cabling is disconnected from C-Bus output units. • Do not megger test the C-Bus cable. 9.0 C-Bus Programming Requirements Unit Address The C-Touch Colour must be programmed with a unique identification address (unit address).
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 10.0 Using the C-Touch Colour Transfer Utility The C-Touch Colour Transfer Utility transfers a software project to the touchscreen. The utility is included with PICED software, that is available from the Downloads section of the CIS web site: http://www.clipsal.com/cis This section takes you through the proccess of installing a project on the C-Touch touchscreen using a direct Ethernet connection.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 2) Remove the fascia if it has been fitted to the unit. 3) Plug the supplied programming lead (red crossover cable) into the RJ45 socket on the front right side of the touchscreen. 4) Ensure that your PC is switched on and plug the other end of the crossover cable into the Ethernet socket on your PC. 5) Wait approximately three minutes to enable the network’s DHCP connection to establish.
5000CTC2 Series C-Touch Colour Touchscreen 9) Installation Instructions You will be asked to select the type of network. Select Local Connection and click OK. Figure 17. Select the network connection type 10) The Transfer Utility software will set the IP Address for the colour touch unit that is compatible with the PC you are using. You might be asked to confirm the suggested address. If so, press Yes on the touchscreen. Figure 18.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 11) If you were asked to reply to a suggested IP Address. You will be asked to confirm your acceptance. 12) If you were asked to confirm the address, click Next. The Transfer Utility software will again search for any touchscreens present on the network. Figure 19. List of touchscreens located by the search 13) Select the touchscreen to be configured. The screen provides information about the selected touchscreen. Figure 20.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 14) Click the Transfer tab to select the transfer page. The transfer options allow you to transfer a project to the touchscreen or transfer a project or log file to the configuration software. 15) Select the button for the Transfer Project to C-Touch Colour. Choose the project that was created for this touchscreen installation. Then press Start to begin the project transfer to the touchscreen.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 16) Click the Control tab to select the Control page shown in Figure 23. From the control screen, you can start and stop the touchscreen’s project (in HomeGate), enable logging, set the time and change the name that identifies the touchscreen over an Ethernet connection. Figure 23. The Control page in the Transfer Utility software 17) Ensure that the time on your PC is set correctly.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 11.0 Reset Button In the event that the C-Touch Colour software becomes unresponsive, you can reset the touchscreen by pressing the reset button. The reset button is located to the right of the display, beneath the fascia (see Figure 25). Instructions for removing the fascia are provided in Section 6 in this document. Figure 25.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 12.0 Specifications Parameter Description Supply voltage 5V d.c., 30 W maximum via power pack* Display type 16.3 cm (6.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 13.0 Dimensions Parameter Description Dimensions (W × H × D) 246 x 173 x 72.5mm (excluding fascia) Protrusion from wall 23.5mm (including glass fascia) Mounting depth (into wall) 54mm Mounting centres (H × V) 212.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 14.0 remote Control and Power Supply Infrared Remote Control Parameter Description Supply voltage 3V d.c. required for normal operation. Transmission range reduces with decreasing battery voltage.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 15.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 16.0 Standards Compiled Declarations of Conformity Australian/New Zealand EMC & Electrical Safety Frameworks and Standards. Regulations Standard EMC Safety Title AS/NZS CISPR 22 IT Equipment Emissions Standard (Class A) AS/NZS CISPR 24 IT Equipment Immunity Standard AS/NZS 60950.1 IT Equipment Safety Standard WARNING: This is a Class A product.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions 17.0 Two Year Warranty The 5000CTC2 Series C-Bus C-Touch Colour Touchscreen carries a two-year warranty against manufacturing defects. Warranty Statement 1. The benefits conferred herein are in addition to, and in no way shall be deemed to derogate; either expressly or by implication, any or all other rights and remedies in respect to the Clipsal product, that the consumer has in the loacation where the product is sold. 2.
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions Notes © Clipsal Australia Pty Ltd 37 of 40
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions Notes 38 of 40 © Clipsal Australia Pty Ltd
5000CTC2 Series C-Touch Colour Touchscreen Installation Instructions Notes © Clipsal Australia Pty Ltd 39 of 40
Technical Support For further assistance in using this product, consult your nearest Clipsal Integrated Systems (CIS) Sales Representative or Technical Support Officer. Technical Support Contact Numbers Australia 1300 722 247 (CIS Technical Support Hotline) New Zealand 0800 888 219 (CIS Technical Support Hotline) Northern Asia +852 2484 4157 (Clipsal Hong Kong) South Africa 011 314 5200 (C-Bus Technical Support) Southern Asia +603 7665 3555 Ext.
