Bluetooth Stereo Headset HCS-100 User manual
[Table of Contents] Before use Package contents Description of parts Wearing Charging Low battery Check battery level How to use Power on Power off Pairing Connecting Answering a call Making a call Ending a call Volume control Functions during a call Listening to music Summary of button functions LED indication and signal sound Supplement Troubleshooting Cautions Additional information Standard and specification Limited warranty 2 3 4 4 5 5 6 6 6 7 10 10 11 11 11 13 14 15 16 18 20 21 22 1
Before use The Clipcomm HCS-100 is a super lightweight and compact Bluetooth wireless stereo headset producing hi-fi stereo sound and offers crystal clear sound via noise reduction and echo cancellation during a phone call using DSP (digital signal processing) technology. [Package contents] Ensure that the items mentioned below are all included in the package. If any item is missing, please contact the dealer.
Before use [Description of parts] (Left) Ear loop Volume controls FWD/RWD Multifunction button Status LED Charging port Microphone (Right) Ear loop 3
Before use [Wearing] Check the left/right side of the headset and wear it appropriately. Adjust the ear loop to fit in your ear if necessary. Right Left [Charging] Open the cover and insert the charger completely into the charging slot until the status LED glows red. Note that connecting the charger while the power is on will turn off the headset. Left 4 The buttons on the headset will not function while charging.
Before use Charge your headset until the status LED turns off. The unit will be fully charged in approximately 2.5 h. WARNING : Do not attempt to charge the HCS-100 with any charger other than the one provided. Using another charger may damage or destroy the headset. [Low battery] The status LED will flash red with a beeping sound that would indicate that the battery charge is low. Charge the battery as soon as the abovementioned phenomenon is detected.
How to use [Power on] 1. Press and hold for 2 s. 2. You will hear a beep and the blue status LED will briefly flash rapidly for 5 times. [Power off] 1. Press and hold for 5 s. 2. You will hear a beep and the blue status LED will briefly flash rapidly for 5 times.
How to use 4. Select “HCS-100” from the list of searched devices. 5. When prompted for a passkey, enter 0000. 6. A beep will sound when the devices are paired successfully. The HCS-100 will turn off automatically if it stays in the “pairing mode” for over 3 min without being paired to any device. In this case, you have to reattempt the pairing process (see abovementioned steps). The connection can be made automatically after pairing depending on the features of different models of mobile phones.
How to use 1. Connect your HCS-100 with MP3 player. 2. Power off the HCS-100 by pressing for 5 s (The connection will drop with MP3 player). 3. Put your HCS-100 in standby mode and connect/pair to mobile phone by headset/hands-free profiles. 4. Press for once shortly. 5. MP3 player is paired with A2DP and AVRCP and the mobile phone is paired with the headset/hands-free profile(s). Auto reconnection 1.
How to use When out of range (greater than 10 m), the connection between the headset and the Bluetooth device will be dropped. If the headset and the Bluetooth device have been separated for over 3 min, up to 10 min will be required for auto reconnection. Connection with the recently connected device HCS-100 can be connected with the recently connected device as follows. 1. In case of multiconnection Hands-free function: Press for once briefly. Stereo headset function: Press for twice briefly. 2.
How to use [Answering a call] The headset and mobile phone will ring simultaneously when an incoming call is received. You can answer a call by pressing briefly (The call can also be answered using the mobile phone). The music will stop temporarily while music is playing and after call ends, music will be played again. In case of multiconnection, MP3 player will not be played depending on the features of different models of devices. [Making a call] Voice dialing* Press and release once.
How to use Last number redialing * Press and hold for 2 s; this will activate the last number redial feature. Subject to different models of mobile phone, it will show you the recently dialed call list; then, you can press and hold for 2 s again to make a call. [Ending a call] To end a call, briefly press . [Volume control] Briefly press the volume up or volume down button located at the side of the headset in order to control the speaker volume. Eight levels of volume control are available.
How to use Call waiting* Answer the second incoming call without ending the first call by pressing for 1 s. To return to the first call, simply press again for 1 s. Call reject* To activate the call reject function, press incoming call is detected. for 1 s when an Mute To activate the mute function, press the volume down button for 5 s; this will mute the sound. When the call mute function is activated, you will hear a beep periodically.
