VX10
The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
UL Safety Fulfillment USER’S MANUAL IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Table of Contents Warning Precautions Components Installation n Opening the Case n Mounting the Camera n Reassemble the Camera Adjustment Specifications Dimension (inches) Sales: 1-800-447-3306 Support: 1-800-549-6393 1 2 4 5 10 11 12 www.clintonelectronics.
Warning The camera requires periodic inspection. Contact an authorised technician to carry out the inspection. Stop using your camera when you find it malfunctioning. If the camera emits smoke or is unusually hot for a long period, a fire may be caused. Do not install the camera on a surface that can not support it. If the camera is installed on an inappropriate surface, it may fall and cause injury. Do not hold plug with wet hands. It could cause an electric shock. Do not dis-assemble the camera.
Precautions Do not install the camera in extreme temperature conditions. Only use the camera under conditions where temperatures are between -20°F ~ 122°F. Be especially careful to provide ventilation when operating under high temperatures. Do not install the camera under unstable lighting conditions. Severe lighting change or flicker can cause the camera to work improperly. Do not touch the front lens of the camera. This is one of the most important parts of the camera.
Do not drop the camera or subject it to physical shocks. It can cause malfunctions to occur. Never keep the camera pointed directly at strong light. It can damage the CCD. Do not expose the camera to radioactivity. If exposed to radioactivity the CCD will fail. Notes • If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur. • Check that the power satisfies the normal specification before connecting the camera.
Components Sales: 1-800-447-3306 Support: 1-800-549-6393 www.clintonelectronics.
Installation Installing the Vandal X Dome Camera: 1. Opening the Case Use the supplied Torx wrench to remove the 3 Torx screws that hold the dome assembly onto the base. Locate and remove the 4 Phillips head screws that hold the inner case onto the camera base. Note: Arrowheads indicate screw location. 5 Sales: 1-800-447-3306 Support: 1-800-549-6393 www.clintonelectronics.
Installation continued 2. Mounting the Camera Remove the camera assembly from the camera base as shown below. If desired apply the EVA foam ring to the bottom of the camera base as shown. Sales: 1-800-447-3306 Support: 1-800-549-6393 www.clintonelectronics.
Installation continued Secure the camera base to the desired mounting surface using the 4 supplied mounting screws. Choose the mounting hole pattern that best suits your application. Multiple mounting hole patterns are provided. Feed the power and video cables through the desired access hole. Note the cable access options shown below. Cable Access Option 1: Stud/wall anchor hole 7 Sales: 1-800-447-3306 Cable Access Option 2: Conduit box hole Support: 1-800-549-6393 www.clintonelectronics.
Installation continued 3. Reassemble the Camera Replace the camera assembly into the mounting base as shown below. Align the tab with the slot when reassembling. Sales: 1-800-447-3306 Support: 1-800-549-6393 www.clintonelectronics.
Installation continued Replace the four screws that hold the camera assembly to the base. Note: Arrowheads indicate screw location. Arrowhead indicates screw location. Before replacing the dome cover you may wish to test the camera with a test monitor. To test, plug in the CE-REMOTE into the DIN connection, and connect your test monitor to the BNC connection located on the CE-REMOTE cable. Refer to camera manual for detailed OSD adjustment settings.
Adjustment The Vandal X Dome Camera has four position adjustments: A. B. C. D. Barrel rotation Lens angle Lateral adjustment (loosen thumb screws on each side to adjust) Camera plate rotation (pinch the camera bracket by each thumb screw to rotate clockwise or counterclockwise) B A C D Tighten the 3 Torx screws that hold the dome cover onto the base to complete installation. Make sure that each screw is tight to ensure superior weather resistance. Sales: 1-800-447-3306 Support: 1-800-549-6393 www.
Specifications Camera CE-VX10 Image Sensor 1/3 Inch SONY Color CCD Resolution 420 TV Lines Effective Pixels 512 (H) x 492 (V) Scanning System 525 Lines, 2:1 Interlace S/N Ratio More than 48dB Sync System Internal Minimum Illumination 1.0 Lux Shutter Speed 1/60 ~ 1/100,000 sec. Lens 4 ~ 9mm Video Output 1.0 Vp-p, 75Ω Power Consumption Max. 110mA (AC24V), Max. 220mA (DC12V) Power Requirement DC12V / AC24V Operating Temperature -20°F ~ 122°F Weather Rating IP 68 Dimensions 5.
Dimensions Ø 4.13” 6” 3.8 5.74” Sales: 1-800-447-3306 Support: 1-800-549-6393 www.clintonelectronics.
MEMO
v.07.09.
