Public View CE-M19S CE-M24S CE-M26S CE-M32S User Manual CLINTON Electronics 6701 Clinton Road Loves Park, IL 61111 1.800.447.3306 Sales 1.800.549.6393 Support 1.800.633.8712 Fax www.clintonelectronics.
Table of Contents Display Camera Introduction………………………………………………………………………… 3 Contents, Installation and Set-up…………………………………………………… 4 Display Functions…………………………………………………………………… 5 LCD Remote Control (M19 & M24 models only)…………………………………… 6 LCD Remote Control (M26 & M32 models only)…………………………………… 7 Display System Settings……………………………………………………………8-9 SD-Card Files……………………………………………………………………… 10 Camera OSD Menu………………………………………………………………… 11 OSD Menu Navigation, Lens……………………………………………………… 12 Exposure………………………………………………
Introduction Congratulations on the purchase of your new Public View Integrated Camera Security display. This display and camera combination is designed for simple and effective loss prevention by making the viewer aware of video surveillance measures.
POWER UP AUTO MENU DOWN 2 16 GB SD Card 16 VOL+ MENU REC GB SD Card EXIT ENTER VOL- MENU/OK Exit OSD GB SD Card Alarm SD-Audio Motion Alarm SD-Audio Chime Motion Chime M26, M32 only M26, M32 only 1 ON 2 1 ON CE-M19S, CE-M24S, CE-M26S, or CE-M32S with access door Extra Case Screws (2) Alarm SD-Audio Motion Chime 2 GB SD-Card (for media) 1 ON 2 3 Remote Control (batteries included) 3 2 4 3 4 Power Pigtail (for Hardwiring) 110VAC Plug User Manual 4 Installation and
Display Functions Features 110VAC Power Supply Input (M26, M32 only) VESA 75 & VESA 100 mounting patterns VGA Output 24VDC Power Supply Input (M26, M32 only) BNC 1 BNC 2 Output BNC 2 Output Input 24VDC Power Supply Input (M19, M24 only) POWER POWER UP AUTO AUTO DOWN UP DOWN Camera & Camera OSD Menu Access Door Camera Video SD Card Slot MENU MENU LCD OSD Menu Buttons LED Flasher IR Sensor Control Access The access door for the SD-Cards, AV connections, and power is located at the back of
Remote Control - M19, M24 models The parameters of the display can be adjusted by using the included remote control. LCD CONTROLS Power Mute Selection Arrows/ Volume Menu DVR REC MENU/OK Exit OSD *NOTE: All other buttons not described are non-functioning on this device. LCD CONTROLS Power – On/Off function. This will power off the display only. The internal camera can still supply video to an external display or DVR. Mute –Disables the audio on the unit.
Remote Control - M26, M32 models The parameters of the display can be adjusted by using the included remote control. LCD CONTROLS Power POWER SOURCE Mute MUTE PIP SWAP AUTO Menu Volume VOL+ MENU Selection Arrows ENTER EXIT VOL- Enter Exit *NOTE: All other buttons not described are non-functioning on this device. LCD CONTROLS Power – On/Off function. This will power off the display only. The internal camera can still supply video to an external display or DVR.
Display Set-Up Video Menu: The display should be pre-set for most installations, however if some adjustment is necessary, we suggest you follow these recommendations by pressing the MENU button on the remote control: 1. First adjust the BRIGHTNESS control to set the black level so that the images are at their brightest while the black images are still black. Do not adjust too high where the black portions of the image become gray or the image will have a “washed out” appearance. 2.
Audio Menu 1. The Audio Menu can be used to raise or lower the volume of the chime or SD-Card activated audio. *NOTE: The MUTE function on the remote control will disable the audio/chime sound. 2. Select the audio source by selecting CHIME to enable the built in chime sound, or SD-AUDIO for the audio on the SD-Card to play. System Settings Menu 1. The LANGUAGE can be changed to one of the following: English, French, German, Spanish, Italian, Dutch, Greek, Swedish. 2.
Change SD-Card Image/Video/Audio POWER AUTO UP DOWN MENU • Insert the SD-Card into your computer or SD-Card reader. • Move the desired JPEG image, or AVI video file into the SD-Card folder. (The required full screen image size is 1024x786) • Leaving multiple media files on the SD-Card will result in the device cycling through all loaded media. • Insert the SD-Card back into the PVM with the contacts facing out, as shown on the right- DO NOT FORCE IT IN.
Accessing the Camera OSD Board The access door to the camera and OSD Board is located at the bottom of the unit. A Phillips screwdriver is required to remove the two access panel screws (Fig. A), place the screws in a location where they will not be lost. The OSD board is attached to the access panel for easy adjustment of the parameters of the camera while viewing the front of the screen (Fig. B). The Zoom and Focus can be adjusted by loosening the two adjustment dials on the lens (Fig. B).
Navigating the OSD Menu 1. Press the SETUP button, then select a menu item from the list available by using the UP and DOWN buttons. • Functions are selected using up and down buttons. • Place the cursor over a desired item, the selected position is displayed. Select the function using the UP or DOWN button. When an arrow is present, press SETUP button to enter sub-menu Change the status using the LEFT or RIGHT button. 2. Set up a selected item by using the Left and Right buttons. 3.
Exposure 1. When the SETUP menu is displayed, select ‘EXPOSURE’ by using the Up and Down buttons so that the arrow indicates ‘EXPOSURE’. Press SETUP to enter. 2. Select the desired mode using Up and Down buttons. BRIGHTNESS: Adjusts the exposure brightness. SHUTTER: You can select either auto or manual shutter. – A.FLK : Select this when you experience picture flicker, which can happen when there is a clash with the frequency of the installed lighting.
Exposure- continued Notes • If you press the SET button in ‘AUTO’ mode, you can adjust brightness by increasing or decreasing the shutter speed. (x2 ~ x512) • Note that the higher the zoom level, the brighter the screen, but the more likely it is that an afterimage will appear. • Although noise, spots, and whitish symptoms may occur in SENS-UP operation when the zoom level is increased, this is normal. White Balance Control Use the White Balance function to adjust the screen color. 1.
SSDR (Super Dynamic Range) SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas. 1. When the SETUP menu screen is displayed, select ‘SSDR’ by using the Up and Down buttons so that the arrow indicates ‘SSDR’. 2.
BLC (Back Light Compensation) 1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Up and Down buttons so that the arrow indicates ‘BACKLIGHT’. 2. Select a desired mode using the Left and Right buttons depending on the camera purpose. BLC: Enables a user to select a desired area on a picture and view that area more clearly.
HLC continued 3. Select a desired mode using the Left and Right buttons and press the SET button. BLC : Select ‘BLC’ to adjust the area to be enhanced then adjust the level. HLC :Enable the user to change the level limit, mask color/tone and area. Notes • For effective license plate observation, it needs minimum illumination and fast shutter speed more than 1/200sec.
DNR3 This function reduces the background noise in a low luminance environment. 1. When the SETUP menu screen is displayed, select ‘DNR’ by using the Up and Down buttons so that the arrow indicates ‘DNR’. 2. Select a desired mode using the Left and Right buttons. OFF: Deactivates DNR. Noise is not reduced. ON : Activates DNR so that noise is reduced. 3. Set the DNR mode to ‘ON’ and press the SET button. Then you can adjust the noise reduction level.
Day / Night You can display pictures in color or black and white. 1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Up and Down buttons so that the arrow indicates ‘DAY/NIGHT’. 2. Select a desired mode using the Left and Right buttons according to the picture display you want. EXTERN : This mode allows you to apply a desired filter to external signals. COLOR : The picture is always displayed in color.
SPECIAL 1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Up and Down buttons so that the arrow indicates ‘SPECIAL’. Press SETUP to enter the ‘SPECIAL’ menu. 2. Select a desired mode using the Up and Down buttons. IMAGE ADJ: 1) When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the Up and Down buttons so that the arrow indicates ‘IMAGE ADJ.’ Press SETUP to enter ‘IMAGE ADJ’. 2) Select a desired mode using the Up and Down buttons.
Image Adj. Continued l FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue) l SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer. Adjust this value appropriately depending on the sharpness of the picture. l RETURN : Select this to save the settings for the IMAGE ADJ. menu and to return to the SETUP menu. Notes • When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
CAM TITLE : If you enter a title, the title will appear on the monitor. 1) If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the arrow indicates ‘CAM TITLE’. 2) Set it to ‘ON’ by using the Left and Right buttons. 3) Press the SET button. 4) Use the 4 direction buttons to move to a desired letter and select the letter by pressing the SET button. Repeat this to enter multiple letters. You can enter up to 15 letters.
SYNC : In areas where the supply is at 60Hz, you can synchronize the output phase of multiple cameras using the power synchronization function (Line-Lock) without using a synchronization signal generator. – INT : Internal Synchronization Type – L/L : Power Synchronization Type, Line-lock l Press the Function Setup switch. l You can select a desired phase from 0 to 359 when select ‘phase’.
Motion Detection- Continued 2) Set up the mode using the 4 direction buttons. – SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high, motion detection sensitivity is increased to recognize even small movement. – AREA MODE : Determines whether to use the MD area selected in SENSITIVITY. – SEL POS : Determines which of the 4 vertices of each MD area is to be used. – XPOS : Determines the coordinate of the horizontal axis for SEL POS.
COMM ADJ (Communication Adjustment) : This function sets up the camera communication status when controlling the camera through an external control device. 1) When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the arrow indicates ‘COMM ADJ’. 2) Set up the mode using the 4 direction buttons. – CAM ID : Determines the camera’s identification number (between 0 and 255). – BAUD RATE : Select 2400/4800/9600/19200/38400/57600 bps.
Troubleshooting If you have trouble operating your device, refer to the following table. If the guidelines do not enable you to solve the problem, contact Clinton Electronics Technical Support at 1-800-549-6393 or 815-633-1444. Problem Nothing appears on the screen. Solution • Check the power connection. • Check the video signal line connection. • Check the Brightness of Auto Iris lens. • Press the POWER button on your remote control. • Check to ensure the proper voltage is applied to the display.
Troubleshooting Problem The MOTION DETECTION function is not working. Solution • Check if ‘MOTION DETECTION’ mode is turned on. • Check if the MD LEVEL is too low. • Check the setting of the MD AREA. Colors are not quite right. • Check the ‘WHITE BAL’ setting. The screen is flickering. • Check if the camera is facing directly into sunlight or fluorescent light. L/L mode isn’t able to be selected. • Have you connected your camera to DC power source? Connect it to AC power source.
v.07.18.
