Instruction Manual

8 6/00
BB7000 Components
Order # Description
Hydraulic motor
High torque, low speed
hydraulic motor mounts
directly to the rotational
drive assembly. Motor ports
are 7/8-14 SAE O-ring type.
Fittings are included with the
hydraulic power unit.
Reverse motor rotational by
switching the hydraulic
hoses at the motor. Motors
can be used on both 4" and
5" diameter bar machines.
Hydraulic fluid lubricates the
motor during operation.
RPM ratings are maximum
for boring bar at 20 gpm
(75.8 L/min). Torque ratings
are constant. All values are
theoretical.
25472 Motor, hydraulic - 3.6 in
3
,
105 rpm, 502 in-lb
25473 Motor, hydraulic - 5.4/5.6
in
3
, 71 rpm, 839 in-lb
25474 Motor, hydraulic - 7.1/7.3
in
3
, 57 rpm, 1047 in-lb
25475 Motor, hydraulic - 8.8/8.9
in
3
, 47 rpm, 1277 in-lb
25476 Motor, hydraulic - 10.6/11.3
in
3
, 37 rpm, 1623 in-lb
25477 Motor, hydraulic - 12.9/14.3
in
3
, 30 rpm, 2023 in-lb
25478 Motor, hydraulic - 16.4/17.9
in
3
, 23 rpm, 2546 in-lb
25587 Hydraulic motor fitting kit
3/4" fittings Kit includes
fittings needed to connect
any hydraulic motor listed
above to hydraulic power
units that have 3/4" female
quick disconnect fittings.
Fittings are included with
every Climax hydraulic
power unit.
15762 Tool kit
Complete set of tools needed
to operate the BB7000
Portable Boring Bar.
Individual parts listed below.
Order # Description
ID-mount self-aligning
bearing support assembly
with jaws Support assembly
mounts to the inside bore of
the work piece. Bar is held in
place by a self-aligning
bearing assembly. Center the
bar by adjusting the four jaws
on the support spider.
Adjustments can be made
from outside the bore.
18886 4" ID-mount bearing support
assembly , 20" - 35" (508 -
899 mm) ID's
19565 4" ID-mount bearing support
assembly , 20" - 49.25" (508 -
1251 mm) ID's
19566 4" ID-mount bearing support
assembly , 20" - 63.5" (508 -
1613 mm) ID's
18885 5" ID-mount bearing support
assembly , 20" - 35" (508 -
889 mm) ID's
18884 5" ID-mount bearing support
assembly , 20" - 49.25" (508 -
1251 mm) ID's
18883 5" ID-mount bearing support
assembly , 20" - 63.5" (508 -
1613 mm) ID's
ID-mount self-aligning
bearing support assembly
with jacking screw legs
Support assembly mounts to
the inside bore of the work
piece. Bar is held in place by a
self-aligning bearing assem-
bly. Center the bar by adjust-
ing the four jacking screw
legs. Adjustments can be
made from outside the bore.
21232 4" ID-mount bearing support
assembly , 10" - 20" (254 -
508 mm) ID's
21926 4" ID-mount bearing support
assembly , 10" - 30" (254 -
763 mm) ID's
21927 4" ID-mount bearing support
assembly , 10" - 40" (254 -
1016 mm) ID's
21294 5" ID-mount bearing support
assembly , 35" - 50" (889 -
1270 mm) ID's