User's Manual
2
Features
z
z
A
A
l
l
a
a
r
r
m
m
A
A
c
c
t
t
i
i
v
v
a
a
t
t
i
i
o
o
n
n
When an alarm is activated, the Indoor Siren will activate its siren and LED light according to
different alarm types:
z Burglar and Emergency alarm: Continuous alarm and LED flash
z Fire alarm: 2-second alarm with1-second interval and continuous LED flash
z
z
A
A
l
l
a
a
r
r
m
m
L
L
e
e
n
n
g
g
t
t
h
h
S
S
e
e
t
t
t
t
i
i
n
n
g
g
z When the Indoor Siren receives an alarm signal via ZigBee network, it will activate alarm
according to the alarm length set by the system control panel.
z If the Indoor Siren receives an alarm signal, but the alarm length duration is not defined by the
system control panel, the Indoor Siren will activate alarm according to Dip Switch setting:
SW1 SW2 SW3 SW4 Siren Duration
ON OFF
OFF OFF
3 minutes
OFF ON
OFF OFF
5 minutes
ON ON
OFF OFF
10 minutes
z
z
B
B
a
a
t
t
t
t
e
e
r
r
y
y
a
a
n
n
d
d
L
L
o
o
w
w
B
B
a
a
t
t
t
t
e
e
r
r
y
y
D
D
e
e
t
t
e
e
c
c
t
t
i
i
o
o
n
n
The Indoor Siren uses four 1.5V alkaline D-cell batteries as its power source. The battery is
included in the package. Open the battery compartment then insert the batteries to power up the
Indoor Siren.
The Indoor Siren features Low Battery Detection function. When the battery voltage is low, the
Indoor Siren will transmit Low Battery signal to the coordinator in ZigBee network.
When changing battery, after removing the old battery, press the Tamper Switch twice to fully
discharge before inserting new battery
z
z
T
T
a
a
m
m
p
p
e
e
r
r
P
P
r
r
o
o
t
t
e
e
c
c
t
t
i
i
o
o
n
n
The Indoor Siren is protected by a tamper switch which is compressed against the front cover when
the cover is closed. Whenever the Indoor Siren front cover is opened, the tamper switch will be
activated. The Indoor Siren will send a tamper open signal to system control panel and activate
alarm immediately according to duration set by the Dip Switches.
z
z
S
S
u
u
p
p
e
e
r
r
v
v
i
i
s
s
i
i
o
o
n
n
The Indoor Siren will transmit a supervision signal to report its condition regularly according to user
setting. The factory default interval is 30 minutes. The user can also press the Function Button
once to transmit a supervision signal manually.
ZigBee Network Setup
z
z
Z
Z
i
i
g
g
B
B
e
e
e
e
D
D
e
e
v
v
i
i
c
c
e
e
G
G
u
u
i
i
d
d
e
e
l
l
i
i
n
n
e
e
ZigBee is a wireless communication protocol that is reliable and has low power consumption and
high transmission efficiency. Based on IEEE802.15.4 standard, ZigBee allows a large amount of
devices to be included in a network and coordinated for data exchange and signal transmission.
Due to the fundamental structure of ZigBee network, ZigBee device will actively seek and join
network after powering on. Since performing a task in connecting network may consume some
power, it is required to follow the instructions to avoid draining battery of a ZigBee device
- Ensure your ZigBee network router or coordinator is powered on before inserting battery into the
ZigBee device.
- Ensure the ZigBee network router or coordinator is powered on and within range while a ZigBee
device is in use.
- Do not remove a ZigBee device from the ZigBee network router or coordinator without removing
the battery from a ZigBee device.
z
z
J
J
o
o
i
i
n
n
i
i
n
n
g
g
t
t
h
h
e
e
Z
Z
i
i
g
g
B
B
e
e
e
e
N
N
e
e
t
t
w
w
o
o
r
r
k
k
As a ZigBee device, the Indoor Siren needs to join a ZigBee network to send and receive alarm
signal. Please follow the steps bellow to join the Indoor Siren into the ZigBee network. Joining
ZigBee network is only allowed during the first 3 minutes of powering up the Siren. If the
Siren has been powered on for more than 3 minutes, please remove and reinsert power to
power on Siren again.
1. Insert the batteries.
2. Press and hold the function button for 10 seconds within 3 minutes after powering up the
Siren then release to join ZigBee network. Please make sure the permit-to-join feature on the