User's Manual

2
1. Plug in the Power Switch into a power outlet.
2. Press and hold the function button for 10 seconds as the Power Switch resets and starts
searching for existing ZigBee network. Please make sure the permit-to-join feature on the router
or coordinator of your ZigBee network is enabled.
3. If the Power Switch successfully joins a ZigBee network, the LED Indicator will flash twice to
confirm.
4. After joining the ZigBee network, the Power Switch will be registered in the network automatically.
Please check the Zigbee network coordinator, system control panel or CIE (Control and
Indicating Equipment) to confirm if joining and registration is successful.
5. If registration and joining to the network is unsuccessful, the Power Switch LED indicator will
flash every 20 minutes after warming up to indicate the situation. Please check your ZigBee
network coordinator, system control panel or CIE setting to ensure the permit-to-join function is
available, and then use the Factory Reset function below to join the ZigBee network.


B
B
i
i
n
n
d
d
i
i
n
n
g
g
w
w
i
i
t
t
h
h
C
C
o
o
n
n
t
t
r
r
o
o
l
l
l
l
e
e
r
r
After joining the ZigBee network, the Power Switch can bind itself with a controller device which
can be used to turn on/off the Power Switch. To bind the Power Switch and the device:
1. Press and hold the Function Button for 3 seconds, then release the button. The Power Switch
will send binding request to the coordinator.
2. Refer to your controller manual to send binding request for the device within 16 seconds.
3. If binding is successful, the Power Switch LED indicator will flash 3 times to confirm. You can
now use the controller to adjust power output level for the Power Switch.
4. If binding is unsuccessful, the Power Switch LED indicator will flash 5 times. Please retry the
binding process.


F
F
a
a
c
c
t
t
o
o
r
r
y
y
R
R
e
e
s
s
e
e
t
t
If you want to remove the Power Switch from current network and join a new network, you need to
use the Factory Reset function to clear the Power Switch from its stored setting and information
first before it can join another network. To perform Factory Reset:
1. Press and hold the switch button for 10 seconds, release the button until the LED Indicator flash
once.
2. The Power Switch has been reset to factory default setting with all its previous network
information removed. It will now actively search for available ZigBee network again and join the
network automatically.
3. If the Power Switch successfully joins a ZigBee network, the LED Indicator will flash twice to
indicate.
4. If the Power Switch cannot find an available ZigBee network, the LED Indicator will flash every
20 minutes to indicate.
Operation


I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
 Plug the Power Switch into a power outlet.
 Plug the appliance into the socket of the Power Switch. The appliance must be in ON status.


A
A
p
p
p
p
l
l
i
i
a
a
n
n
c
c
e
e
C
C
o
o
n
n
t
t
r
r
o
o
l
l
 After the Power Switch has successfully joined a ZigBee network, the coordinator can
remotely turn on/off the Power Switch to control the appliance
 You can also press the button on the Power Switch to toggle its on/off status
 If you have bound a controller with the Power Switch, you can also use the controller to turn
on/off the Power Switch.
 If the Power Switch is removed from power outlet, after replugging the Power Switch, its
previous on/off status will be restored within 1 minute


M
M
a
a
x
x
i
i
m
m
u
u
m
m
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
L
L
o
o
a
a
d
d
 For 110V: the maximum operation load is 1760W and 16A.
 For 230V: the maximum operation load is 3680W and 16A.