Product Info

ManualsBrandsClimax Technology ManualsElectronicsRemote Keypad

Table Of Contents

Federal Communication Commission Interference Statement

REMOTE KEYPAD (KPT-35-COMBO)

KPT-35-COMBO is a hardwired Remote Keypad designed to have quick access control of the System Control Panel via PIN Code

or RFID tags. The keypad can send wired and wireless signals to and receive signals from the Control Panel within 500ft (152m)

in wire distance. The LCD screen will display any information the system control panel sends back.

The Remote Keypad can either be mounted on a flat surface or wall with screws. It also has a tamper protection switch which will

be activated upon any unauthorized attempt to open the back cover.



Parts Identification

1. Backlit LCD Display

2. Green LED

- The Green LED is off in stand-by mode.

- The Green LED will light up when any key is pressed.

3. Yellow LED

- The Yellow LED will flash once every 3 seconds when any fault situation is detected, and turn to OFF when all fault

conditions are restored.

4. Backlit Numeric Keys

5. Backlit Star (

＊

) Key

6. Backlit Pound (

＃

) Key

7. Backlit OK Key

- For confirming the keyed-in data or confirming the selection.

8. Backlit Restore ( ) Key

- This key is is used for deleting a digit, canceling the selection, aborting the current screen, and returning to the previous

screen etc.

9. Backlit Arm/



Key

- Use this key to move the cursor and scroll the display upwards

- The key is also used for entering “Away Armed” mode.

10. Backlit Arm/



Key

- Use this key to move the cursor and scroll the display downwards.

- The key is also used for entering “Home Armed” mode.

11. Backlit RFID Sensor Zone

12. Buzzer

13. Battery Compartment

14. Keypad Terminal

- Hardwiring the four terminals (V, G, A, B) to the Keypad Terminal on the Control Panel. Up to four KPT-35-COMBOs can

be connected in series. For keypad wiring, refer to Keypad Wiring section on the next page for detail.

15. Wire Management Hole

- Prepunched hole used to enhance wiring management flexibility.

16. Jumper Switch

- Ensure the furthest keypad’s Jumper Switch is set to ON to serve as a terminating resistor.

17. Tamper Switch

Jumper On

The jumper link is inserted

connecting the two pins

Jumper Off

if the jumper link is

removed

or “parked” on one pin.

Summary of content (8 pages)

PAGE 1
REMOTE KEYPAD (KPT-35-COMBO) KPT-35-COMBO is a hardwired Remote Keypad designed to have quick access control of the System Control Panel via PIN Code or RFID tags. The keypad can send wired and wireless signals to and receive signals from the Control Panel within 500ft (152m) in wire distance. The LCD screen will display any information the system control panel sends back. The Remote Keypad can either be mounted on a flat surface or wall with screws.
PAGE 2
18. 19. 20. 21. Bracket Holes x 3 Mounting Holes x 4 Bottom Fixing Screw x 1 RFID Tag Caution   Wiring of the Remote Keypad should only be performed by certified technician with proper knowledge and training in electric equipment. Before installation or any maintenance work, make sure the power supply of the Control Panel has been disconnected. Features  Battery and Low Battery Detection  Two L91 1.
PAGE 3
The Keypad Terminal can be hardwired to the Control Panel in series within 500ft (152m) in wire distance.  KPT-35-COMBO-A is wired correctly as it is within 500ft (152m) of the Control Panel, in wire distance.  KPT-35-COMBO-B is wired correctly as it is within 500ft (152m) of the Control Panel, in wire distance. Before tightening the cover fixing screw of the keypad, ensure its jumper switch is set to ON to serve as a terminating resistor since it has the furthest distance from the Control Panel.
PAGE 4
Code. Please enter a PIN Code for the tag, and press the OK key to confirm setting. Learning is now complete. The Tag information has been added into the Keypad with corresponding PIN Code. You can now use the Tag to Arm/Home Arm/Disarm the Control Panel through the Remote Keypad. 5.  If a tag you wish to learn already exists in the Keypad, 2 beeps will be emitted when the Keypad detects the tag, and “RFID already Exist” will be displayed on the LCD screen.
PAGE 5
 Away Arm: Select “Away Arm” and press the OK key to change system mode to “Away Armed”.  Home Arm: Select “Home Arm” and press the OK key to change system mode to “Home Armed”  Alarm Memory: This option will become available after an alarm is triggered. Entering the Keypad’s User Menu will be directed to the Alarm Memory option automatically. Press OK to confirm selection, and then use  and  key to view the alarm memory.
PAGE 6
 Press the OK key once. When “Enter PIN Code” is displayed on the LCD screen, press and hold the OK key for 10 seconds.  “KP will reset in 2 seconds” will be displayed on the LCD screen along with a long beep.  “Scanning Network” will be displayed on the LCD screen while the Remote Keypad is sending learning code to the Control Panel.  When the Keypad is added into the Control Panel, “Learning Success” will be displayed on the LCD screen along with 2 beeps.
PAGE 7
 Reset Remote Keypad to Factory Default The Remote Keypad can be reset to clear all learnt-in data and return all settings to default value by following the steps below: 1. Please follow Change of Battery steps for factory default. 2. Within 10 seconds after inserting batteries, enter “0000”. When the last digit of “0000” turns into “” on the LCD screen, press “#” to reset the Remote Keypad to default value. 3.
PAGE 8
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.