User's Manual

ManualsBrandsClimax Technology ManualsElectronicsRemote Keypad

REMOTE KEYPAD with NFC Tag (KPT-32N, KPT-32N-F1)

April 01st, 2016

z Identifying the Parts

1. Siren

2. Orange LED: Home Arm Key

. Red LED: Away Arm Key

4. Panic Alarm (if enabled)

- Press both 1 and 3 to trigger panic alarm

5. Fire Alarm (if enabled)

- Press both 4 and 6 to trigger fire alarm

6. Medical Alarm (if enabled)

- Press both 7 and 9 to trigger Medical alarm

7. ¿ Key

- Enter Keypad PIN Code + ¿ Key to enter Test Mode.

8. Keypad Sensor (for tag)

9. NFC Tag

10. # Key

11. Mounting Holes

12. Tamper Switch

<NOTE>

A short beep will sound along with key pressing to indicate that the button pressed is valid.

& A long beep will sound along with key pressing to indicate successful command.

& 4 continuous beeps will sound indicating mistake and the user should repeat the process again.

& Backlight will be ON for any key pressed or command sent from the Keypad.

z LED Indicator

z Red LED (Away Arm Key)

z Red LED on: the system is in Test Mode.

z Red LED: Red flashes, and Backlight on in the Away Arm Mode.

z Red LED flash with 4 beeps: failure due to the following reasons:

¾ No response from the control panel.

¾ Request for Home mode during Arm mode.

¾ Request for Force arm.

z Orange LED (Home Arm Key)

z Orange LED: Orange flashes and backlight on in the Home Mode.

z Orange LED flashes for 5 seconds: low battery in Normal Operation Mode, and Tamper open.

z LED flash with 4 beeps: failure due to the following reasons:

¾ No response from the control panel.

¾ Request for Home mode during Arm mode.

¾ Request for Force arm.

Summary of content (5 pages)

PAGE 1
REMOTE KEYPAD with NFC Tag (KPT-32N, KPT-32N-F1) April 01st, 2016 z Identifying the Parts 1. Siren - Press both 7 and 9 to trigger Medical alarm 2. Orange LED: Home Arm Key 7. ¿ Key 3. Red LED: Away Arm Key - Enter Keypad PIN Code + ¿ Key to enter Test Mode. 4. Panic Alarm (if enabled) 8. Keypad Sensor (for tag) - Press both 1 and 3 to trigger panic alarm 9. NFC Tag 5. Fire Alarm (if enabled) 10. # Key - Press both 4 and 6 to trigger fire alarm 11. Mounting Holes 6.
PAGE 2
& When Arm/Home, Red/Orange LED will turn off after successful completion of a valid keystroke sequence, or when & z Built-in Siren I. II. III. z Exit Delay — the Remote keypad continuously beeps. If enter Arm mode or Home Mode, Remote Keypad will emit long beep. Entry Delay —The Remote keypad continuously beeps. When entering Disarm Mode, the Remote Keypad will emit 2 beeps. Alarm siren — Siren will sound continuously when an alarm is triggered. Fire Alarm will sound 2 seconds and 1 second off.
PAGE 3
Step 3. Step 3. Step 4. z Tamper Protection z z z Press ＊ key and then 7 key to transmit learn code to Control Panel. Refer to Control Panel manual to complete the learning process. If learning is successful, the Keypad will emit 3 beeps upon receiving acknowledgement signal from Control Panel. If the Keypad does not sound 3 beeps, please restart learning procedure from Step 1.
PAGE 4
z Mounting Remote Keypad To mount the remote keypad: I. Remove the front cover. II. Using the 2 mounting holes of the back cover as a template, mark off the positions in the most appropriate place. III. Insert the wall plugs if fixing into plaster or brick surface. IV. Screw the Remote keypad onto the wall plugs. V. Replace the front cover.
PAGE 5
d) z When incorrect Keypad PIN code is entered to enter Test mode, The Keypad will emit 4 beeps. If incorrect Keypad PIN codes are entered for 4 times, the Keypad will disable key input function for 1 minute and indicate error by flashing all LEDs for 6 times and emitting 6 beeps. All key press during the next 1-minute period will be ignored.