HSGW Series IP Alarm System User Manual May-18-2020
Table of Contents 1. INTRODUCTION _________________________________________________________________________ 1 1.1. SYSTEM SPECIFICATION _____________________________________________________________________ 2 2. PANEL INFORMATION ___________________________________________________________________ 4 2.1. IDENTIFYING THE PARTS: ____________________________________________________________________ 4 2.2. THE POWER SUPPLY: _______________________________________________________________________ 5 2.3.
8.1. ADMINISTRATOR SETTING __________________________________________________________________ 46 8.2. HOME AUTOMATION ______________________________________________________________________ 47 8.3. SCENE _________________________________________________________________________________ 52 8.4. REPORTING _____________________________________________________________________________ 54 8.5. CODE SETTINGS __________________________________________________________________________ 57 8.6.
1. Introduction This section covers unpacking your IP Security System with HSGW Series IP Panel and Security Sensors. Refer to later chapters for information on setting up and configuring the system over the Web Page in more detail. The advanced IP Security System with fully integrated TCP/IP technology and Ethernet connectivity is able to take full advantage of new advances in IP Home Security and Home Automation and multi-path signalling.
1.1.
Battery Duration 2 hours or more Battery Recharge Time to 80% of 600mAH 72 hours Current Drain AC Powered 169mA standby, 766mA at full load. Battery Powered 158mA standby, 914mA at full load.
2. Panel Information 2.1. Identifying the parts: 1 LED 1 (Red/Green) Red LED ON – Area 1 in Full Arm Mode. Red LED Flash – Area 1 in Home 1/2/3 Mode. Green LED ON - System in the learning mode. Green LED Flash - System in the Walk Test mode. 2 LED 2 (Red/Green) Red LED ON – Area 2 in Full Arm mode Red LED Flash – Area 2 in Home 1/Home 2/Home 3 mode Green LED On – System in the learning mode Green LED Flash – System in the Walk Test mode 3 LED 3 (Red/Yellow) Red LED ON – Alarm in memory.
2.2. The Power Supply: An AC power adapter is required to connect to a wall outlet. Be sure only to use an adapter with the appropriate AC voltage rating to prevent component damage. DC 12V 1A switching power adaptor is used to power the Control Panel with 7.2V, 660mAh, Ni-mH rechargeable battery pack. Rechargeable Battery HSGW-G8 Series includes 7.
3. Getting Started Read this section of the manual to learn how to set up your Control Panel and program System Settings over the Web page. 3.1. System Deployment Follow guidelines below when planning installation location: The Control Panel requires Ethernet connection. The Control Panel should be installed at a location that is hidden from outside view. Avoid mounting the Control Panel near large metal objects which may affect wireless radio strength.
3.3. Software Installation ※ THIS INSTALLATION IS ONLY REQUIRED FOR FIRST TIME USER ※ 1. RUNNING THE FINDER SOFTWARE The Finder software is required for your computer to identify the control panel on the LAN. Step 1. To download Finder software, open your browser and type below URL in the address bar: http://www.climax.com.tw/climax-download-finder.html. 2. Step 2. After download, install the software and follow on-screen instructions to complete installation. Step 3.
Step 5. Double click on the “Finder.exe” to start the software. Finder will automatically search for control panel on the LAN and display its information. If available, the panel’s LAN IP address, Firmware version and MAC address will be displayed Step 6. If the panel information is not displayed, check panel power and Ethernet connection and click on “Search” to update the panel information. Step 7.
The LanType is default to DHCP and does not require manual input of IP/Netmask/Gateawy/DNS setting. If you wish to configure these setting manually, change LanType to Static. After finish changing network setting, enter the user name (default: admin) and password (default: cX+HsA*7F1) then click OK to confirm. The user name and password can be changed later in panel configuration webpage Step 8.
4. Connection to Panel Webpage For first time setup, webpage connection is only available within 1 hour after the panel is powered on; if the panel has been powered on for more than 1 hour. Webpage access will be disabled. Reboot the panel to enable webpage function again. Change default password after login to gain unrestricted webpage access. Step 1. Select the Control Panel in the Finder software and click on “Open Webpage” to connect to panel webpage.
The Welcome page displays current control panel firmware version information according to different panel model and MAC address. If the default login password is not changed, webpage access will be disabled 1 hour after power on. Reboot the panel and changed password to allow unrestricted webpage access.
5. Device Management The Device Management section allows you to learn in, edit, control and view all available accessory devices that can be included in the HSGW Series Control Panel. 5.1. Learning Use this function to add new devices into the Control Panel. HSGW Series supports up to 160 zones of accessory devices, in 2 areas, up to 80 zones each area. The following types of accessory devices are supported: RF device: All Climax RF devices are supported.
Device section. If not, the sensor information will be displayed in the Detected Device section. For VST-862 F1 devices, press and hold the learn button for 3 seconds for the Control Panel to receive a learn code, and then click “Add” within 30 seconds. Step 6. If the device is successfully learnt into the system, the added device will be displayed in the “Learned Device” section. Step 7. Repeat Step 3~5 to learn in all device, click Stop to exit learn mode when complete.
Step 4. After finish learning all devices, press and holde the Learn button for 1 second. The Control Panel will emit 2 short beeps to indicate it has returned to normal mode. LED1 will dim. Device learnt in via Local Learning will be assigned to Area 1 only, which is limited to 80 devices. The Control Panel cannot enter learning mode when under Away Arm/Home Arm or Walk Test mode. The Control Panel will emit 5 beeps to indicate error. 5.1.3.
Step 3. Edit your device setting and information according to instruction below. Click “OK” to save your new changes when finished. Alternatively, click “Default” to reset all parameters to default values or click “Reset” to re-enter all the information. Name: Enter a name for the device. Area: Select the area which the device belongs to. Zone: Select the Device zone number. Attribute List: The attribute list determines panel behaviour when the panel receives trigger signal from the device.
This function ONLY applies to Remote Control or Door Contact with Set/Unset attribute enabled. Latch Report ON: When the device is used to change systm arm mode, the Control Panel will report the arm/disarm action by the particular device. Latch Report OFF: When the device is used to change systm arm mode, the Control Panel will not report the arm/disarm action by the particular device. Set/Unset This function is for Door Contact only. This function allows Door Contact to control system mode.
When the system is in Full Arm or Home Arm mode mode, if a sensor set to Burglar Follow is triggered, the Control Panel will report a burglar alarm immediately. When a Start Entry sensor is triggered and the system is under Entry Delay Timer countdown, if a sensor set to Burglar Follow is triggered, the Control Panel will wait until the Entry Delay Timer expires before activating a burglar alarm. If the system is disarmed before the timer expires, the Control Panel will not activate alarm.
A sensor set to 24HR attribute will ignore Disarm, Full Arm, Home are and Exit response setting. The panel will activate selected alarm when this sensor is triggered regardless of system mode under any time. Some devices have their own unique functions and will have its own attribute setting which is not listed in this section. Please refer to the device manual for its setting detail. 5.1.4. Delete Devices Step 1. To delete a sensor, click “Delete” under “Device List” Step 2.
Step 2. Select Area and Zone number for the device you wish to add into system. Step 3. Enter the device RF code, and preferred device name (up to 31 characters) Step 4. Press “OK” to save Step 5. If the RF code you entered is valid, the device will be added into the system according to the Area and Zone number. You do not need to learn the device as instructed in 5.1.1. Add Sensor. 5.3. Learn Rule You can enter the sensor RF code or manually to assign area and zone number to this sensor.
Step 6. Enter a preferred name for sensor (up to 31 letters or numbers). Step 7. Press “OK” to save. Step 8. If the process is successful, the screen will display “Updated Successfully.” You can then check, edit or delete the rule under the Learn Rule menu. Step 9 Repeat the steps to add more rules. Step 10. Learn in the sensors you have entered rules for according to 5.1.1 Add Sensor. Learn rule function is only used to pre-assign area and zone number to sensors before learning.
5.4. Walk Test This is to test the sensor operation range for installation purpose. Step 1. Click “Start” to enter Walk Test mode. Step 2. Press the test button on the sensor(s) or any button on the Remote Controller or triggering the sensor. Step 3. When the Control Panel receives a signal, it will show as below and a 2-tone beep will be heard to indicate that it is safe to install the particular sensor in the location.
5.5. Exclusion This feature is only available for Z-Wave modules only, or when a Z-wave dongle is inserted into the Control Panel. This feature is for you to remove Z-Wave device only. Step 1. Click on “Exclusion” and click on “Start” to start the procedure. Then the Panel will enter the removing mode. Step 2. Refer to the Z-Wave device manual to transmit signal. Step 3. Select the desired Z-Wave and click delete to remove it from the Z-wave list under Device List section (Panel).
5.6. Z-Wave Tool The Z-wave Tool is used to reset Z-wave module to factory default and remove all Z-wave devices, or change routing setting. Step 1. Click ”Z-Wave Factory Reset”, the Z-Wave module is reset to factory default and all Z-Wave devices will be removed automatically. The Control Panel Home ID will also be changed automatically for a newly added Z-Wave device to recognize. Step 2. The list of Z-Wave devices is still displayed in the Panel webpage.
5.7. PSS Control This feature is designed to control/edit/delete Power Switches included in the panel. Click Edit to edit attributes of power switches. Click Delete to remove power switch from panel. Click Switch On/Switch Off to turn on/off power switches. Or click Switch Toggle to toggle between on/off status. For Power Switch Dimmer, you can also set its power output level with the slide down menu.
5.8. UPIC Control UPIC Control webpage allows you to control UPIC IR Transmitter included in Control Panel Transmit IR Signal Depending on the UPIC model number, select the function to be performed in the drop down menu, then click “Setup UPIC” for the UPIC to transmit IR Signal. UPIC5 LED Setup (UPIC5 only) UPIC5 has 6 IR LEDs, a central one and 5 surrounding ones.
5.9. Surveillance The PIR Camera/Video Cameras and IP Cameras are listed under Surveillance for separate control. Click Edit to edit camera attributes. Click Delete to remove device from panel. Click Request Media to capture a picture or vide PIR camera: A picture will be captured upon request PIR Video Camera: A 10-second video will be recorded upon request IP Camera: The IP Camera will record a video according to its video length setting (Please refer to IP Camera manual for detail.
5.10. Group Control This feature is designed for you to edit a name of group, switch on or off a group of Power Switches. You can also assign Power Switches to groups you desire. 5.10.1. Group Control/Edit Step 1. Specify a new name for a group. Step 2. Click Switch On or Switch Off to turn on or off one group of power switches. 5.10.2 Device Edit/Delete Step 1. Check on the groups you wish to assign the Power Switch. This is a multiple-choice field and you can assign one Power Switch to multiple groups.
5.11. Sound/Siren Setting The Sound/Siren Setting page includes setting Siren configuration function. 5.11.1. Device Edit/Delete Click Edit to edit the Siren’s attribute, volume and voice settings, or Delete to delete the Siren.
The Device Edit page is only available for the newest BX/Siren series and BX series without DIP Switch. Edit your Siren setting and information accordingly to instruction below. Click “OK” to save your new changes when finished. Alternatively, click “Default” to reset all parameters to default values or click “Reset” to re-enter all the information. Name: Enter a name for the Siren. Area: Select the area which the Siren belongs to. Zone: Select the Siren zone number.
Control Panel is put into Full Arm Mode. Home arm confirm beep: set the volume of the confirm beep sound of the Siren when Control Panel is put into Home Arm Mode. Disarm confirm beep: set the volume of the confirm beep sound of the Siren when Control Panel is put into Disarm Mode. Exit beeps of full arm: set exit countdown beep volume under Full Arm Mode. Exit beeps of home arm: set exit countdown beep volume under Home Arm Mode.
5.11.2. RF Siren Setup Tamper On/Off You can enable/disable all RF Sirens tamper protection with this function. Select to turn on or off the sirens tamper function. When turned off, if siren tamper will be enabled again automatically after one hour if not turn on manually during the one hour period.
6. Program the System After the initial set-up, you can then program your system by clicking on the left menu to set them individually. 6.1. Panel Condition In the Panel Section, user can arm, disarm or partially arm the system. Besides, it displays the current Panel Status & Device Information. Panel Control Select a choice to arm, disarm or partially arm the system. Panel Status The Control Panel will update the panel status periodically.
inform you to recharge the battery. Tamper: (reserved) Interference: This is for you to check whether the Control Panel is purposely interfered. The jamming period detected will be accumulated, and when the total period exceeds 30 seconds within 1 minute, a “Jamming” message will be shown and reported to the Central Monitoring Station accordingly. AC activation: To check whether AC power is connected. If not, it will show “AC Failure”.
- After pressing Reset Panel, the Control Panel will restart in 60 seconds and all configured values will be kept without any change. Note The function is designed for installer to make a note for each control panel. The note you make here can be delivered to a server over XMPP or polling protocol.
6.2. Panel Settings Program the Panel, Time and Sound Settings at your discretion. Panel Setting AC Fail Report: When an AC power failure is detected, your Control Panel will report to the Central Monitoring Station according to the duration set under AC Fail Report. If 5 minutes is set, the event will be automatically reported to the CMS after 5 minutes. Your Control Panel will start to use its battery power instead of the mains power until the fault even is cleared.
Auto Check-in: this is to select whether the Control Panel needs to send check-in reporting to the Central Station automatically and to select the period of time between check-in reports. Options available are Disable, 1 hour, 2 hours, 3 hours… up to 4 Weeks. Auto Check-in Offset Period: This is to set the time delay before the first Auto Check-In report is made.
Supervision Timer: The Control Panel monitors accessory devices according to the supervision signal transmitted regularly from the device. User this option to set a time period for receiving supervision signals. If the Control Panel fails to receive supervision signal from a device within this duration, it will consider the device out of order and report the event accordingly. Entry Delay 1 for Full Arm: Set Entry Delay Timer 1 for full arm mode.
The Control Panel sounds a Door Chime (Ding-Dong Sound) while the DC and/or IR is activated in Disarm / Full / Home / Entry mode. Entry Delay Sound for Full Arm: this is for you to decide whether the Control Panel sounds count-down beeps and volume of beep during the entry delay time in the full arm mode. Exit Delay Sound for Full Arm: this is for you to decide whether the Control Panel sounds count-down beeps and volume of beep during the exit delay timer in the full arm mode.
6.3. PIN Code The User PIN Codes are used by Remote Keypad accessory to control system mode remotely. The 2 areas in the control panel each has 30 User PIN Codes available for setting. Each consists of 4-6 digits (numeric number 0~9), no disallowed PIN code. User PIN code #1 for each Area is always activated factory default. User PIN #1 in Area 1 User PIN #1 in Area 2 Password: 1234 Password: 4321 Area Area: Select the area for setting User PIN Code.
7. Network Settings 7.1. GSM (HSGW-G8 Series only) Check SIM This is designed for the system to check the SIM card or not. (If users do not intend to use the GSM funciton, please tick “NO” to ensure the system will not check if the SIM card is inserted or not and it will not display the GSM fault by LED flashing.) GPRS In order to allow GPRS to serve as a back-up IP Reporting method, this section will need to be programmed before reporting.
Password (GPRS) It is the User Password to input before accessing the GPRS feature. Please inquire your service provider. All values will be applied to both Areas 1 & 2. MMS The MMS settings are offered by your telecom service provider. Before configuring this function, contact your service provider for correct MMS setting information of the inserted SIM card. APN (Access Point) Name Enter a MMS APN name provided by your service provider.
Step 1. Click Send SMS. Step 2. Enter a desired phone number and text message. Reset GSM This feature is designed for you to reset GSM module. Step 1. Click GSM Reset. Step 2. A pop-out message “Are you sure?” is displayed. Click Yes to confirm resetting.
7.2. Network This is for you to program the Network for IP connection. Obtain an IP address automatically (DHCP) If DHCP is selected, the Network will obtain an IP address automatically with a valid Network DHCP Server. Therefore, manual settings are not required. This is only to be chosen if your Network environment supports DHCP. It will automatically generate all information.
7.3. Wireless Use “Wireless” webpage to setup the panel’s WiFi setting There are 3 ways you can connect to the wireless network. 1. Search for WiFi AP: Click “Scan WiFi AP” to search for available wireless network Select the available Wireless APs from the list by clicking “Set” after AP info column and enter the required information (pre-shared key, etc.) and click the “OK” button. 2. Enter the Wireless information manually and click “OK” to connect.
7.4. UPnP UPnP is Universal Plug and Play, which opens networking architecture that leverages TCP/IP and the Web technologies to enable seamless proximity networking in addition to control and data transfer among networked devices in the home, office, and public spaces. Enable UPnP Device: When enabled, you will be able to see this device via any UPnP discovery tool Enable UPnP Port Redirect: The device will try to find an UPnP-supported router and set up the port to redirect to the router.
8. System Settings 8.1. Administrator Setting For setting new Administrator Log-in Name and Password. Please note both User Name and Password are case sensitive. Step 1. Enter the preferred User Name. Step 2. Enter the preferred Password in the “New Password” field and repeat the same Password in the Repeat Password field.
8.2. Home Automation It is used to set Home Automation rules to control sensors and home appliances. You can set up to 100 rules. Step 1. Click on Edit. Step 2. Select an operation area. Step 3. Set a rule condition. Step 4. Set a rule schedule. Step 5. Select the corresponding action rules in the Execution field. Area Select an opeartion area. Rule Condition The rule condition determines under which circumstances the rule should be activated.
Mode Change and Exit Timer Stopped : When set as Mode Change and Exit Timer Stopped, when the system changes mode to and Exit Delay Timer expires, , the rule will be activated according to rule schedule and execution setting. Mode Start Entry Timer : When set as Mode Start Entry Timer, when the system begins to countdown Entry Delay, the rule will be activated according to rule schedule and execution setting.
LUX Between : When set as LUX Between, if the lux reading from specified light sensor falls below the level specified, the rule will be activated according to rule schedule and execution setting. Random : The Random condition must be used along with Rule Schedule setting. Set a percentace from 1 to 10%. When the panel time reaches programmed Rule Schedule time. The Panel will activate rule according to set chance.
Zone Swich On : Turn on the Power Switch at specified zone. Zone Swich On For : Turn on the Power Switch at specified zone for a set duration. Zone Switch Level:: Change the power output level for Dimmer at specified zone. Zone Swich Toggle : Toggle on/off the Power Switch at specified zone. Group Switch Off : Turn off all Power Switches assigned to specified group. Group Switch On : Turn on all Power Switches assigned to specified group.
Request Image (All, No Flash) : All PIR Cameras in the system will take a picture without activating LED Flash. Request Video : The PIR Video Camera or IP Camera in specified zone will record a video. Request Video (All) : All PIR Video Cameras and IP Cameras in the system will record a video. Setup UPIC:: The UPIC and specified zone will transmit Off/Heat/Cool command to the air conditioner as programmed.
8.3. Scene The Scene setting allows you to customize a series of actions with your devices, such as Power Switch control, image/video request, mode change and trigger alarm. The programmed scene can be set to activated when a device is triggered. (See 5.1.3. Edit Devicesl), or when a Home Automation Rule is excecuted. (See 8.2.
Step 5. Repeat Step 2-3 to setup the execution you wanted. As many as 5 executions can be included in one scene. Step 6. Click “Done”. Step 7. Click “OK” at bottom of webpage to confirm the new scene setting..
8.4. Reporting This is used for installer to program/ set all requirements for reporting purposes. Reporting URL This is used for installer to program report destinations. 1 Climax CID protocol via IP Format: ip://(Account Number)@(server ip):(port)/CID Example: ip://1234@54.183.182.247:8080/CID 2 SIA DC-09 protocol via IP Format: ip://(Account Number)@(server ip):(port)/SIA Example: ip://1234@54.183.182.
Example: ip://1234@54.183.182.247:8080/CID_SIA/KEY/4A46321737F890F654D632103F86B4 F3 6 CSV protocol via IP Format: ip//(Account Number)@(server ip):(port)/CSV Example: ip://1234@54.183.182.247:8080/CSV 7 CSV protocol via IP including username and password Format: ip//(Account Number)@(server ip):(port)/CSV/User/Pasword Example: ip://1234@54.183.182.247:8080/CSV/abcd/1357 8 Email Format: mailto:user@example.com Example: mailto:john@gmail.
will only report to Group 3 if reporting to Group 2 fails. 1 Retry/ 3 Retry/ 5 Retry/ 10 Retry/ 99 Retry: If reporting to all destinations in a group fails, the system will retry reporting to the group according to the retries times set here. When the panel is registered into Climax’s Home Portal Server, URL1 will be filled in with Home Portal Server report information. Do not change the information once registration is complete or reporting to Home Portal Server may encounter error.
8.5. Code Settings The Duress Code, Master Code & Temporary Code adds the flexibility of different security level for operation in Code Settings menu. Step 1. Key in your preferred 4-6 digit Installer Code, Duress Code, Master Code, and/or Temporary Code. Step 2. You can also choose to have Latch Option On / Off for Temporary Code by tick the Latch Option box and press OK to confirm the settings.
Area Each Area has different Duress Code, Master Code, and Temporary Code. Select the Area to program the code setting in this area. Duress Code The Duress Code is designed for transmitting a secret & silence alarm. When Duress Code is used for accessing the system, the Control Panel will report a secret alarm message without sounding the siren to the Central Monitoring Station to indicate of a Duress Situation in Progress.
8.6. SMTP Setting Program the mail server related settings. The email account you set here would be used to send report for events or picture and video clip captured by PIR Camera and PIR Video Camera. Step 1. Enter the following settings: Server: set the mail server (max. 60 digits/alphabets). Port: set the port number (max. 5 digits/alphabets). User: set the mail account name (max. 30 digits/alphabets). Password: set the password corresponding to the mail account name (max.
8.7. Media Upload The system can deliver captured images and video clips captured by PIR Cameras and PIR Video Camera to cell phone, email or ftp. FTP: ftp://user.password@server/path Manitou: manitou://user@server:port HTTP: http://ip:port/path Email: mailto:user@server (transmitting an alarm image over Ethernet) MMS via Telephone: mms: telephone number MMS via GPRS: mms: user@mail.
8.8. Polling The polling function enables the Control Panel to query the destiation you set (URL1 or URL2) in turn as to whether it has any data to transmit.
8.9. XMPP XMPP setting enables the Control Panel to query the set destination. This setting is required for the Control Panel to connect to Climax’s Home Portal Server for remote control. If the panel is disconnected from the server, it will retry connection every 3 minutes. Server: server address (dependent upon default firmware) US server: us.vestasmarthome.com EU server: eu.vestasmarthome.com Taiwan server: tw.vestasmarthome.
8.10. Date & Time Program the current Date & Time and set automatic synchronization with internet time server. Date & Time: set current month, date and time. Time Zone: choose your time zone, and then the system will calculate the daylight saving time automatically (if necessary). Internet Time: the system will automatically synchronize with an internet time server. Tick the check box to enable this function. Available options: time1.google.com, pool.ntp.org, time.nist.gov and tick.usno.navy.mil.
8.11. Dynamic DNS This page is used to provide you the Control Panel’s current public IP address. Dynamic DNS Server: http://checkip.dyndns.
8.12. Test IP This is for you to test the Control Panel internet connection. Step 1. Enter the URL destination you want to test connection to. Step 2. Enter the test interval. Step 3. Click “OK” You can check the test connect result in System Log.
8.13. Firmware Upgrade You can update the firmware via this web page. Step 1. Click on “Browse” and locate the latest firmware file (“unzipped image.bin” file) in your PC. Step 2. Press “Apply” to upload the latest firmware to Control Panel Step 3. Wait for 1 min and do NOT power off during this time. Step 4.
8.14. RF Firmware Upgrade You can update the Control Panel’s RF firmware via this web page. Step 1. Click on “Browse” and locate the latest firmware file (“unzipped image.bin” file) in your PC. Step 2. Press “Apply” to upload the latest firmware to Control Panel Step 3. Wait for 1 min and do NOT power off during this time. Step 4.
8.15. Factory Reset Yan can clear all programmed parameters in the Control Panel and reset it to Factory Default. Once the Factory Reset is executed, all the programmed settings will returned to its default value, and all the learnt-in devices will be removed. You will need to restart the programming and learning process again. Remote Reset Step 1. Tick the Kept current network setting or Kept current device list box to keep the current Network settings.
Local Reset Step 1. Disconnect the AC adaptor, slide battery switch to OFF. Step 2. Press and hold the reset button and connect the AC adaptor to the Control Panel. DO NOT release the button yet. Step 3. Keep holding the reset button for about 45 seconds then release until you hear one long beep. The 3 LEDs will flash 3 times. Step 4. Release the button and wait for the Control Panel to reboot.
8.16. Backup & Restore Yan can backup all programmed parameters and save these programmed values into a file. Besides, you also can restore pre-programmed settings. 8.16.1 Backup Data Yan can backup all programmed data and save these programmed values into a file. Step 1. Click Download configuration file. Step 2. Click Download configuration file. 8.16.2 Restore Settings Step 1. Click Browse, select a saved file. Step 2. Click Apply to apply the pre-programmed values to the main unit.
8.17. System Log The sytem log webpage logs the control panel’s detail system operation history. System Log File Download” Click to download a detail log files into your computer for more information.
9. Event & History This section introduces event history of the system. 9.1. Captured Events This page stores all captured pictures and videos by PIR Camera and PIR Video Camera. When a PIR Camera is triggered, it will take 3 pictures in quick succession, when a PIR Video Camera is triggered, it will take a 10-second video clip. You can also request the PIR Camera to take a picture and PIR Video Camera to take a 10-second video clip manually.
9.2. Reported Events This page stores all triggered events by the control panel by recording the events’ CID event code and report status. Reload : Click to refresh the page content Limit # of Items: Click the drop down menu on the pageto select the numbers of captured events you want to display.
9.3. Event Log The Event Log page records specific actions performed by the Control Panel and accessory devices. Reload : Click to refresh the page content Limit # of Items: Click the drop down menu on the pageto select the numbers of captured events you want to display.
9.4. Device History You can track your accessory device status history under Device History. For Power Switch Meter or Temperature Sensor, the update history power consumption or temperature ireading will be displayed under this page (the current info is also displayed under Panel and PSS Control). Reload : Click to refresh the page content Limit # of Items: Click the drop down menu on the pageto select the numbers of captured events you want to display.
10. Appendix 10.1. Fault Event Description During operation, when the panel detects faulty events, the panel will log the event and make reports. When fault events exist in the system, the panel Fault LED will light up and the panel will emit a beep every 30 seconds. Fault Event Table Fault Event Descriptions The Control Panel’s AC power is disconnected When AC failure is detected, the panel will turn off both Ethernet and mobile network functions when idle to conserve power.
10.2.
24H – Smoke Instant Smoke Alarm Instant Smoke Alarm Instant Smoke Alarm Instant Smoke Alarm Instant Smoke Alarm Instant Smoke Alarm 24H – Medical Instant Medical Alarm Instant Medical Alarm Instant Medical Alarm Instant Medical Alarm Instant Medical Alarm Instant Medical Alarm 24H – Fire Instant Fire Alarm Instant Fire Alarm Instant Fire Alarm Instant Fire Alarm Instant Fire Alarm Instant Fire Alarm 24H – Water Instant Water Alarm Instant Water Alarm Instant Water Alarm Instant Wate
10.3. Cross Zone Verification Cross Zone Verification is use to setup cross verification for intrusion sensors. To use Cross Zone Verification, the following sensor and panel setting must be adjusted: 1 At least 1 intrusion sensor must be set to Cross Zone attribute. 2 The Cross Zone Timer option under Panel Setting webpage must be enabled. Cross Zone Verification Rule Cross Zone function does not activate under Exit and Entry Time.
10.5. Contact-ID Protocol & Format Where ACCT MT QXYZ GG C1C2C3 ACCT = 4 Digit Account number (0-9, B-F) MT = Message Type, 18H. Q = Event qualifier, which gives specific event information: XYZ = Event code (3 Hex digits 0-9, B-F) = Group, Partition number (00H), or Area Number GG - 00 = panel - 01= area 1….....xx= area xx = 1. For devices: zone C1C2C3 = Zone number 001, Zone 1 002, Zone 2 ………………….. XXX Zone XXX 2.
10.6. Event Code 100 – Medical When a device set to Medical attribute is triggered. 101 – Personal emergency When a device set to Personal Emergency attribute is triggered. 110 – Fire When a device set to Fire attribute is triggered. 111 – Smoke When the Smoke Detector (SD) set to Smoke Alarm is triggered. When the Smoke Detector (SD) set to Fire Verification verifies an alarm during Fire Verification Time.
supervision timer. When the panel receives signal again from sensor that previously failed supervision. 154 – Water leakage When the Water Sensor connected to Door Contact set at Water (@W) is triggered. 158 – High Temperature Alarm When high temperature alarm is triggered. 159 – Low Temperature Alarm When low temperature alarm is triggered. 162 – CO Alarm 170 – High Power Consumption When high power consumption alarm is triggered.
401 – Remote Arm/Disarm When the system is armed or disarmed by SMS message or web access 407 – Disarm/Away Arm/Home Arm by Remote Keypad 408 – Set/Unset Arm/Disarm When the DC set at Set\Unset is triggered. 456 - Partial Arm When partially arm the system from Disarm to Home arm 570 – Device out of order/ Door Contact Not Closed When any device is out of order after the preset exit delay time is reached Door Contact is not closed after the preset exit delay time is reached.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15, 2, 22, 24 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
