Specifications

ManualsBrandsClimateMaster ManualsHeat PumpTYH/V 024 - 060 60Hz - HFC-410A

ClimateMaster works continually to improve its products. As a result, the design and specications of each

product at the time of order may be changed without notice and may not be as described herein. Please contact

ClimateMaster's Customer Service Department at 1-405-745-6000 for specic information on the current design and

specications. Statements and other information contained herein are not express warranties and do not form the

basis of any bargain between the parties, but are merely ClimateMaster's opinion or commendation of its products.

The latest version of this document is available at climatemaster.com.

*LC377* LC377

Revised: 17 July, 2013

TranquiliTy

Single-STage (TS) SerieS

SubmiTTal DaTa

moDelS TSD/H/V 006 - 070

60H

z - HFC-410a

engliSH language/i-P uniTS

Submittal Data - i-P unitS

Unit Designation:

Job Name:

Architect:

Engineer:

Contractor:

Performance Data

Cooling Capacity: Btuh

EER:

Heating Capacity: Btuh

COP:

Ambient Air Temp: °F

Entering Water Temp (Clg): °F

Entering Air Temp (Clg): °F

Entering Water Temp (Htg): °F

Entering Air Temp (Htg): °F

Airow: CFM

FanSpeedorMotor/RPM/Turns:

Operating Weight: (lb)

electrical Data

PowerSupply: Volts

Phase Hz

MinimumCircuitAmpacity:

MaximumOvercurrentProtection:

Summary of content (72 pages)

PAGE 1
Tranquility® 20 Single-Stage (TS) Series Submittal Data Models TSD/H/V 006 - 070 60Hz - HFC-410A English Language/I-P Units Submittal Data - I-P Units Unit Designation: Job Name: Architect: Engineer: Contractor: Performance Data Cooling Capacity: Btuh EER: Heating Capacity: Btuh COP: Revised: 17 July, 2013 Ambient Air Temp: °F Entering Water Temp (Clg): °F Entering Air Temp (Clg): °F Entering Water Temp (Htg): °F Entering Air Temp (Htg): °F Airflow: CFM Fan Speed or Motor/RPM/Turns: Oper
PAGE 2
Tranquility® 20 Single-Stage (TS) Series Submittal Data Models TSD/H/V 006 - 070 60Hz - HFC-410A English Language/S-I Units Submittal Data - S-I Units Unit Designation: Job Name: Architect: Engineer: Contractor: Performance Data Cooling Capacity: kW EER: Heating Capacity: kW COP: Revised: 17 July, 2013 Ambient Air Temp: °C Entering Water Temp (Clg): °C Entering Air Temp (Clg): °C Entering Water Temp (Htg): °C Entering Air Temp (Htg): °C Airflow: l/s Fan Speed or Motor/RPM/Turns: Operatin
PAGE 3
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Table of Contents *Page Number Unit Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Selection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 TS Series Nomenclature. . . . . . . . . . . . .
PAGE 4
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Unit Features The Tranquility® 20 Single-Stage (Ts) Series unit features The award winning Tranquility Series raises the bar for water-source heat pump efficiencies, features and application flexibility. Not only does the Tranquility® 20 far exceed ASHRAE 90.1 efficiencies, but it also uses EarthPure® (HFC-410A) zero ozone depletion refrigerant, making it an extremely environmentally-friendly option.
PAGE 5
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Selection Procedure Reference Calculations Heating Cooling LWT = EWT - HE GPM x 500 LWT = EWT + LAT = EAT + HC CFM x1.08 LAT (DB) = EAT (DB) - HR GPM x 500 LC = TC - SC SC CFM x1.
PAGE 6
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Selection Procedure Step 1 Determine the actual heating and cooling loads at the desired dry bulb and wet bulb conditions. Step 2 Obtain the following design parameters: Entering water temperature, water flow rate in GPM, air flow in CFM, water flow pressure drop and design wet and dry bulb temperatures. Air flow CFM should be between 300 and 450 CFM per ton.
PAGE 7
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P TS Series Nomenclature 1 2 Model Type 3 4 5 6 7 8 9 10 11 12 13 15 TS V 0 2 4 A G C 3 0 C L T S TS = Tranquility® 20 Single Stage Scroll (Rotary: Size 006-012) Standard S = Standard Supply Air & Motor Option Configuration Option T D B S V U Y Z K N P W V = Vertical Upflow H = Horizontal D = Vertical Downflow Unit Size 006 - E,G 009 - E,G 012 - E,G 018 - E,G 024 - E,F,G,H 030 - E,F,G,H 036 - E,F,G,H 042 - F,G,H,N 048 - F,G,H,N 060 - F,G,H
PAGE 8
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – AHRI/ASHRAE/ISO 13256-1 ASHRAE/AHRI/ISO 13256-1. English (I-P) Units Water Loop Heat Pump Model Fan Motor Cooling 86°F Capacity Btuh EER Btuh/W Ground Water Heat Pump Heating 68°F Capacity Btuh COP Cooling 59°F Ground Loop Heat Pump Heating 50°F Capacity Btuh EER Btuh/W Capacity Btuh COP Cooling 77°F Heating 32°F Capacity Btuh EER Btuh/W Capacity Btuh COP 3.4 TSH/V006 PSC 6,300 15.7 8,000 5.4 7,400 25.
PAGE 9
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – Selection Notes For operation in the shaded area when water is used in lieu of an antifreeze solution, the LWT (Leaving Water Temperature) must be calculated. Flow must be maintained to a-level WPD Cooling EAT such 80/67°F EWT that theGPM LWT is maintained above 40°F [4.4°C] when the Airflow Sens/Tot °F TC below). SC Otherwise, kW HR PSI clipped FT (see JW3 jumper is not example CFM Ratio appropriate properN/A antifreeze should be 20 5.
PAGE 10
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V 006A (PSC Blower) Performance capacities shown in thousands of Btuh 240 CFM Nominal (Rated) Airflow Cooling, 240 CFM Nominal (Rated) Airflow Heating EWT °F 20 30 40 50 60 70 80 85 90 100 110 120 GPM 2.0 2.0 1.0 1.0 1.5 1.5 2.0 2.0 1.0 1.0 1.5 1.5 2.0 2.0 1.0 1.0 1.5 1.5 2.0 2.0 1.0 1.0 1.5 1.5 2.0 2.0 1.0 1.0 1.5 1.5 2.0 2.0 1.0 1.0 1.5 1.5 2.0 2.0 1.0 1.0 1.5 1.5 2.0 2.0 1.0 1.0 1.5 1.5 2.0 2.0 1.0 1.0 1.5 1.5 2.0 2.
PAGE 11
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V 009B (PSC Blower) 350 CFM Nominal (Rated) Airflow Cooling, 350 CFM Nominal (Rated) Airflow Heating EWT °F 20 30 40 50 60 70 80 85 90 100 110 120 GPM 2.8 2.8 1.4 1.4 2.1 2.1 2.8 2.8 1.4 1.4 2.1 2.8 2.8 1.4 1.4 2.1 2.1 2.8 2.8 1.4 1.4 2.1 2.1 2.8 2.8 1.4 1.4 2.1 2.1 2.8 2.8 1.4 1.4 2.1 2.1 2.8 2.8 1.4 1.4 2.1 2.1 2.8 2.8 1.4 1.4 2.1 2.1 2.8 2.8 1.4 1.4 2.1 2.1 2.8 2.8 1.4 1.4 2.1 2.1 2.8 2.8 1.4 1.4 2.1 2.1 2.8 2.
PAGE 12
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V 012A (PSC Blower) 350 CFM Nominal (Rated) Airflow Cooling, 350 CFM Nominal (Rated) Airflow Heating EWT °F 20 30 40 50 60 70 80 85 90 100 110 120 GPM 3.5 3.5 1.8 1.8 2.6 2.6 3.5 3.5 1.8 1.8 2.6 2.6 3.5 3.5 1.8 1.8 2.6 2.6 3.5 3.5 1.8 1.8 2.6 2.6 3.5 3.5 1.8 1.8 2.6 2.6 3.5 3.5 1.8 1.8 2.6 2.6 3.5 3.5 1.8 1.8 2.6 2.6 3.5 3.5 1.8 1.8 2.6 2.6 3.5 3.5 1.8 1.8 2.6 2.6 3.5 3.5 1.8 1.8 2.6 2.6 3.5 3.5 1.8 1.8 2.6 2.6 3.5 3.
PAGE 13
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 018B (PSC Blower) 600 CFM Nominal (Rated) Airflow Cooling, 600 CFM Nominal (Rated) Airflow Heating EWT °F 20 30 40 50 60 70 80 85 90 100 110 120 GPM 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.
PAGE 14
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 018B (ECM Blower) 750 CFM Nominal (Rated) Airflow Cooling, 750 CFM Nominal (Rated) Airflow Heating EWT GPM °F 20 20 20 30 30 30 30 30 30 30 40 40 40 40 40 40 40 50 50 50 50 50 50 50 60 60 60 60 60 60 60 70 70 70 70 70 70 70 80 80 80 80 80 80 80 85 85 85 85 85 85 85 90 90 90 90 90 90 90 100 100 100 100 100 100 100 110 110 110 110 110 110 110 120 120 120 120 120 120 120 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.8 2.8 4.1 4.1 5.5 5.5 2.
PAGE 15
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 024 (PSC Blower) 850 CFM Nominal (Rated) Airflow Cooling, 850 CFM Nominal (Rated) Airflow Heating EWT °F 20 30 40 50 60 70 80 85 90 100 110 120 GPM 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.
PAGE 16
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 024 (ECM Blower) 850 CFM Nominal (Rated) Airflow Cooling, 950 CFM Nominal (Rated) Airflow Heating EWT °F GPM 20 20 20 30 30 30 30 30 30 30 40 40 40 40 40 40 40 50 50 50 50 50 50 50 60 60 60 60 60 60 60 70 70 70 70 70 70 70 80 80 80 80 80 80 80 85 85 85 85 85 85 85 90 90 90 90 90 90 90 100 100 100 100 100 100 100 110 110 110 110 110 110 110 120 120 120 120 120 120 120 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.
PAGE 17
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 030 (PSC Blower) 950 CFM Nominal (Rated) Airflow Cooling,950 CFM Nominal (Rated) Airflow Heating EWT °F 20 30 40 50 60 70 80 85 90 100 110 120 GPM 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.0 4.0 4.0 6.0 6.0 8.0 8.
PAGE 18
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 030 (ECM Blower) Performance capacities shown in thousands of Btuh 1,000 CFM Nominal (Rated) Airflow Cooling, 1,100 CFM Nominal (Rated) Airflow Heating EWT °F GPM 20 20 20 30 30 30 30 30 30 30 40 40 40 40 40 40 40 50 50 50 50 50 50 50 60 60 60 60 60 60 60 70 70 70 70 70 70 70 80 80 80 80 80 80 80 85 85 85 85 85 85 85 90 90 90 90 90 90 90 100 100 100 100 100 100 100 110 110 110 110 110 110 110 120 120 120 120 120 120 120 8.
PAGE 19
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 036 (PSC Blower) 1,250 CFM Nominal (Rated) Airflow Cooling, 1,250 CFM Nominal (Rated) Airflow Heating EWT °F 20 30 40 50 60 70 80 85 90 100 110 120 WPD GPM 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.0 4.5 4.5 6.8 6.
PAGE 20
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 036 (ECM Blower) 1,250 CFM Nominal (Rated) Airflow Cooling, 1,250 CFM Nominal (Rated) Airflow Heating EWT °F GPM 20 20 20 30 30 30 30 30 30 30 40 40 40 40 40 40 40 50 50 50 50 50 50 50 60 60 60 60 60 60 60 70 70 70 70 70 70 70 80 80 80 80 80 80 80 85 85 85 85 85 85 85 90 90 90 90 90 90 90 100 100 100 100 100 100 100 110 110 110 110 110 110 110 120 120 120 120 120 120 120 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.0 4.5 4.5 6.8 6.8 9.0 9.
PAGE 21
TS Series 60Hz - HFC-410A Submittal Data 1,400 CFM Nominal (Rated) Airflow Cooling, 1,400 CFM Nominal (Rated) Airflow Heating EWT °F 20 30 40 50 60 70 80 85 90 100 110 120 GPM 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.
PAGE 22
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 042 (ECM Blower) 1,400 CFM Nominal (Rated) Airflow Cooling, 1,400 CFM Nominal (Rated) Airflow Heating EWT °F GPM 20 20 20 30 30 30 30 30 30 30 40 40 40 40 40 40 40 50 50 50 50 50 50 50 60 60 60 60 60 60 60 70 70 70 70 70 70 70 80 80 80 80 80 80 80 85 85 85 85 85 85 85 90 90 90 90 90 90 90 100 100 100 100 100 100 100 110 110 110 110 110 110 110 120 120 120 120 120 120 120 11.0 11.0 5.5 5.5 8.3 8.3 11.0 11.0 5.5 5.5 8.3 8.3 11.
PAGE 23
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 048 (PSC Blower) 1,600 CFM Nominal (Rated) Airflow Cooling, 1,600 CFM Nominal (Rated) Airflow Heating EWT °F 20 30 40 50 60 70 80 85 90 100 110 120 GPM 12.0 12.0 6.0 6.0 9.0 9.0 12.0 12.0 6.0 6.0 9.0 9.0 12.0 12.0 6.0 6.0 9.0 9.0 12.0 12.0 6.0 6.0 9.0 9.0 12.0 12.0 6.0 6.0 9.0 9.0 12.0 12.0 6.0 6.0 9.0 9.0 12.0 12.0 6.0 6.0 9.0 9.0 12.0 12.0 6.0 6.0 9.0 9.0 12.0 12.0 6.0 6.0 9.0 9.0 12.0 12.0 6.0 6.0 9.0 9.0 12.0 12.
PAGE 24
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 048 (ECM Blower) 1,550 CFM Nominal (Rated) Airflow Cooling, 1,650 CFM Nominal (Rated) Airflow Heating EWT °F GPM 20 20 20 30 30 30 30 30 30 30 40 40 40 40 40 40 40 50 50 50 50 50 50 50 60 60 60 60 60 60 60 70 70 70 70 70 70 70 80 80 80 80 80 80 80 85 85 85 85 85 85 85 90 90 90 90 90 90 90 100 100 100 100 100 100 100 110 110 110 110 110 110 110 120 120 120 120 120 120 120 12.0 12.0 6.0 6.0 9.0 9.0 12.0 12.0 6.0 6.0 9.0 9.0 12.
PAGE 25
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 060 (PSC Blower) 1,950 CFM Nominal (Rated) Airflow Cooling, 1,950 CFM Nominal (Rated) Airflow Heating EWT °F 20 30 40 50 60 70 80 85 90 100 110 120 WPD GPM 15.0 15.0 7.5 7.5 11.3 11.3 15.0 15.0 7.5 7.5 11.3 11.3 15.0 15.0 7.5 7.5 11.3 11.3 15.0 15.0 7.5 7.5 11.3 11.3 15.0 15.0 7.5 7.5 11.3 11.3 15.0 15.0 7.5 7.5 11.3 11.3 15.0 15.0 7.5 7.5 11.3 11.3 15.0 15.0 7.5 7.5 11.3 11.3 15.0 15.0 7.5 7.5 11.3 11.3 15.0 15.0 7.
PAGE 26
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 060 (ECM Blower) 1,825 CFM Nominal (Rated) Airflow Cooling, 2,050 CFM Nominal (Rated) Airflow Heating EWT °F GPM 20 20 20 30 30 30 30 30 30 30 40 40 40 40 40 40 40 50 50 50 50 50 50 50 60 60 60 60 60 60 60 70 70 70 70 70 70 70 80 80 80 80 80 80 80 85 85 85 85 85 85 85 90 90 90 90 90 90 90 100 100 100 100 100 100 100 110 110 110 110 110 110 110 120 120 120 120 120 120 120 15.0 15.0 7.5 7.5 11.3 11.3 15.0 15.0 7.5 7.5 11.3 11.
PAGE 27
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 070 (PSC Blower) 2,100 CFM Nominal (Rated) Airflow Cooling, 2,100 CFM Nominal (Rated) Airflow Heating EWT °F 20 30 40 50 60 70 80 85 90 100 110 120 GPM 16.5 16.5 8.3 8.3 12.4 12.4 16.5 16.5 8.3 8.3 12.4 12.4 16.5 16.5 8.3 8.3 12.4 12.4 16.5 16.5 8.3 8.3 12.4 12.4 16.5 16.5 8.3 8.3 12.4 12.4 16.5 16.5 8.3 8.3 12.4 12.4 16.5 16.5 8.3 8.3 12.4 12.4 16.5 16.5 8.3 8.3 12.4 12.4 16.5 16.5 8.3 8.3 12.4 12.4 16.5 16.5 8.3 8.
PAGE 28
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Performance Data – TS H/V/D 070 (ECM Blower) 1,950 CFM Nominal (Rated) Airflow Cooling, 2,100 CFM Nominal (Rated) Airflow Heating EWT °F GPM 20 20 20 30 30 30 30 30 30 30 40 40 40 40 40 40 40 50 50 50 50 50 50 50 60 60 60 60 60 60 60 70 70 70 70 70 70 70 80 80 80 80 80 80 80 85 85 85 85 85 85 85 90 90 90 90 90 90 90 100 100 100 100 100 100 100 110 110 110 110 110 110 110 120 120 120 120 120 120 120 16.5 16.5 8.3 8.3 12.4 12.4 16.5 16.5 8.3 8.3 12.4 12.
PAGE 29
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Air Flow Correction Table PSC Fan Motor Airflow Cooling Heating % of Rated Total Capacity Sensible Capacity S/T Power Heat of Rejection 68.75% 0.9465 0.8019 0.8472 0.9614 0.9496 75% 0.9602 0.8350 0.8696 0.9675 81.25% 0.9724 0.8733 0.8981 0.9744 87.50% 0.9831 0.9149 0.9306 93.75% 0.9923 0.9578 0.9653 Heating Capacity Power Heat of Extraction 0.9617 0.9740 1.0936 0.9425 0.9728 0.9810 1.0635 0.9592 0.9821 0.9829 0.
PAGE 30
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Entering Air Correction Tables Heating Entering Heat Heating Air DB Power of Capacity Extraction °F 1.0514 0.7749 1.1240 45 50 1.0426 0.8113 1.1032 55 1.0329 0.8525 1.0802 60 1.0224 0.8980 1.0551 65 1.0114 0.9473 1.0282 68 1.0046 0.9786 1.0115 70 1.0000 1.0000 1.0000 75 0.9883 1.0556 0.9706 80 0.9764 1.1135 0.
PAGE 31
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Correction Tables - Antifreeze and Water Pressure Drop Adder for Options Cooling Heating EWT 90°F EWT 30°F Antifreeze Type Antifreeze % Total Cap Sens Cap Power Htg Cap Power WPD Corr. Fct. EWT 30°F Water 0 1.000 1.000 1.000 1.000 1.000 1.000 5 0.995 0.995 1.003 0.989 0.997 1.070 15 0.986 0.986 1.009 0.968 0.990 1.210 25 0.978 0.978 1.014 0.947 0.983 1.360 1.
PAGE 32
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Blower Performance Data – Standard Unit - No Reheat (PSC Motor) Airflow in CFM with wet coil and clean air filter Model Rated Airflow Min CFM 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.60 0.
PAGE 33
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Blower Performance Data – Units with ClimaDry® (PSC Motor) Coil Face Velocity FPM TSH/V/D with Reheat ESP Loss TSH/V/D 018 In. of Water TSH/V/D 024, 030 In. of Water TSH/V/D 036 In. of Water TSH/V/D 042, 048 In. of Water TSH/V/D 060, 070 In. of Water 200 0.037 0.033 0.031 0.028 0.026 250 0.052 0.046 0.042 0.038 0.034 300 0.077 0.066 0.059 0.051 0.044 350 0.113 0.096 0.085 0.073 0.061 400 0.181 0.160 0.145 0.131 0.
PAGE 34
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P ECM Control The ECM fan is controlled by an interface board that converts thermostat inputs and field selectable CFM settings to signals used by the ECM motor controller. Units manufactured after July 2005 have version II (P/N 17B0019N01). Fan speeds are selected with a nine position DIP switch for version II. To take full advantage of the ECM motor features, a multi-stage thermostat should be used (2-stage heat/2-stage cool or 3-stage heat/2-stage cool).
PAGE 35
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P ECM Control The ECM motor includes “soft start” and “ramp down” features. The soft start feature is a gentle increase of motor rpm at blower start up. This creates a much quieter blower start cycle. The ramp down feature allows the blower to slowly decrease rpm to a full stop at the end of each blower cycle. This creates a much quieter end to each blower cycle and adds overall unit efficiency.
PAGE 36
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P ECM Control Dehumidification Mode Settings: The dehumidification mode setting provides field selection of humidity control. When operating in the normal mode, the cooling airflow settings are determined by the cooling tap setting above. When dehumidification is enabled there is a reduction in airflow in cooling to increase the moisture removal of the heat pump.
PAGE 37
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Blower Performance Data – (ECM Motor) - Standard Unit - No Reheat Residential Units Only Airflow in CFM with wet coil and clean air filter Model 018 024 030 036 042 048 060 070 Max ESP (in. wg) 0.50 0.50 0.50 0.50 0.50 0.75 0.75 0.
PAGE 38
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P ClimaDry® II Option - Benefits and Application ClimaDry® II Modulating Reheat Option ClimateMaster’s patented ClimaDry® II Dehumidification option is an innovative means of providing modulating reheat without the complication of refrigeration controls. ClimaDry® II is hot gas generated reheat, which utilizes one of the biggest advantages of a Water-Source Heat Pump (WSHP), the transfer of energy through the water piping system.
PAGE 39
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P ClimaDry® II Option - Benefits and Application With the ClimaDry® II option, return air from the space is cooled by the air-to-refrigerant (evaporator) coil, and then reheated by the water-to-air (reheat) coil to dehumidify the air, but maintain the same space temperature (thus operating as a dehumidifier). The moisture removal capability of the heat pump is determined by the unit’s latent capacity rating.
PAGE 40
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P ClimaDry® II Option - Sequence of Operation ClimaDry® II Sequence of Operation - A heat pump equipped with ClimaDry® II can operate in three modes; cooling, cooling with reheat (dehumidification), and heating. The cooling/heating modes are like any other ClimateMaster WSHP. The reversing valve (“O” signal) is energized in cooling, along with the compressor contactor(s) and blower relay. In the heating mode the reversing valve is de-energized.
PAGE 41
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P ClimaDry® II Option - Sequence of Operation 1st Stage Heating: A simultaneous call from (G) and (Y1) to the (G) and (Y1) terminals of the DXM control board will bring the unit on in 1st Stage Heating. 2nd Stage Heating: A simultaneous call from (G), (Y1), and (Y2) to the (G), (Y1), and (Y2) terminals of the DXM control board will bring the unit on in 2nd Stage Heating.
PAGE 42
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Physical Data Model 006 009 Compressor (1 Each) 012 018 024 030 036 Rotary Factory Charge HFC-410A (oz) [kg] 042 048 060 070 80 [2.27] 136 [3.86] 144 [4.08] Scroll 24 [0.68] 32 [0.91] 34 [0.96] 50 [1.13] 56 [1.59] 58 [1.64] 70 [1.98] 80 [2.
PAGE 43
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P TS - Horizontal – Dimensional Data Horizontal Model Overall Cabinet *A Width B Length C Height 006 012 in cm 22.4 56.8 43.1 107.8 17.3 43.1 018 in cm 22.4 56.8 62.2 158.0 19.3 48.9 024 030 in cm 22.4 56.8 62.2 158.0 19.3 48.9 036 in cm 25.4 64.5 71.2 180.8 21.3 54.0 042 048 in cm 25.4 64.5 76.2 193.5 21.3 54.0 060 070 in cm 25.4 64.5 81.2 206.2 21.3 54.0 *Does not include air filter supports. Add 2” (5.1cm) when a 1” (25.
PAGE 44
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P TS - Horizontal – Dimensional Data Discharge Connection Duct Flange Installed Horizontal Model Return Connection Using Return Air Opening Return Connection Using Optional Air Filter Frame M N O Supply Height P Supply Width Q R S Return Width T Return Height U V S Return Width T Return Height U V 006 - 012 in cm 5.3 13.4 4.1 10.3 9.0 22.5 9.0 22.5 5.3 13.4 4.1 10.3 17.1 43.4 15.3 38.9 2.1 5.3 1.0 2.5 17.7 45.0 14.2 36.1 2.3 5.
PAGE 45
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P TS - Vertical Upflow – Dimensional Data Overall Cabinet Vertical Upflow Model *A Width B Depth C Height Water Connections Vertical Upflow Model 1 2 3 4 5 Loop In D Loop Out E HWG In F HWG Out G H Water Loop FPT HWG FPT 006 012 in cm 22.4 56.8 21.6 54.9 34.5 87.6 018 in cm 22.4 56.8 25.6 65.1 44.6 113.3 006 012 in cm 3.7 9.4 9.7 24.6 N/A N/A 7.4 18.7 1/2” N/A 024 030 in cm 22.4 56.8 25.6 65.1 48.5 123.
PAGE 46
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P TS - Vertical Upflow – Dimensional Data Discharge Connection Duct Flange Installed Vertical Upflow Model Return Connection Using Return Air Opening Return Connection Using Optional Air Filter Frame M N O Supply Width P Supply Depth Q R S Return Depth T Return Height U R S Return Depth T Return Height U 006 012 in cm 6.7 17.0 6.3 16.0 9.0 22.9 9.0 22.9 6.7 17.0 2.3 5.8 17.1 43.3 15.3 38.9 1.0 2.5 1.7 4.3 17.7 45.0 14.2 36.1 1.
PAGE 47
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P TS - Vertical Downflow – Dimensional Data Vertical Downflow Model Overall Cabinet *A Width B Depth C Height 018 in cm 22.4 56.8 25.6 65.1 48.4 122.9 024 030 in cm 22.4 56.8 25.6 65.1 52.5 133.4 036 in cm 25.4 64.5 30.6 77.8 54.5 138.4 042 048 in cm 25.4 64.5 30.6 77.8 58.5 148.6 060 070 in cm 25.4 64.5 30.6 77.8 62.5 158.8 *Does not include air filter supports. Add 2” (5.1cm) when a 1” (25.4mm) filter is used, add 3” (7.
PAGE 48
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P TS - Vertical Downflow – Dimensional Data Discharge Connection Duct Flange Installed Vertical Downflow Model Return Connection Using Return Air Opening Return Connection Using Optional Air Filter Frame M N O Supply Width P Supply Depth Q R S Return Depth T Return Height U R S Return Depth T Return Height U 018 in cm 6.7 17.1 8.4 21.4 10.1 25.7 9.1 23.0 10.8 27.4 2.2 5.6 21.1 53.6 23.7 60.2 21.2 53.8 1.7 4.3 22.2 56.4 22.2 56.
PAGE 49
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Corner Weights for TSH Series Units Model 006 009 012 018 024 030 036 042 048 060 070 Lbs Total Left-Front* Right-Front* Left-Back* Right-Back* 136 45.0 30.0 33.0 28.0 kg 62 20.4 13.6 15.0 12.7 Lbs 156 55.0 33.0 36.0 32.0 kg 71 24.9 15.0 16.3 14.5 Lbs 160 56.0 34.0 37.0 33.0 kg 73 25.4 15.4 16.8 15.0 Lbs 257 78.1 64.6 66.2 47.5 kg 117 35.4 29.3 30.0 21.6 Lbs 266 78.8 67.2 69.9 50.2 kg 122 35.
PAGE 50
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Electrical Data – PSC Motor & ClimaDry® All TS Units with Standard PSC Motor Model 018 024 030 036 042 048 060 070 TS Units with PSC Fan Motor and ClimaDry® TS Units (PSC) Compressor LRA Fan Motor FLA Total Unit FLA Min Circuit Amp Max Fuse/ HACR Reheat Pump FLA Total Unit FLA Min Circuit Amp Max Fuse/ HACR 9.0 48.0 1.0 10.0 12.3 20 0.8 10.8 13.1 20 8.4 40.0 0.9 9.3 11.4 15 0.7 10.0 12.1 20 1 12.8 60.0 1.1 13.
PAGE 51
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Electrical Data – High Static PSC Motor & ClimaDry® All TS Units with High Static PSC Fan Motor Model 018 024 030 036 042 048 060 TS (H.S. PSC) Units TS Units with H.S. PSC Fan Motor and ClimaDry® LRA Fan Motor FLA Total Unit FLA Min Circuit Amp Max Fuse/ HACR Reheat Pump FLA Total Unit FLA Min Circuit Amp Max Fuse/ HACR 9.0 48.0 1.1 10.1 12.4 20 0.8 10.9 13.2 20 8.4 40.0 0.9 9.3 11.4 15 0.7 10.0 12.1 20 1 12.8 60.
PAGE 52
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Electrical Data – ECM Motor & ClimaDry® All TS Units with ECM Fan Motor Model 018 024 030 036 042 048 060 070 TS Units with ECM Fan Motor and ClimaDry® TS Units (ECM) LRA Fan Motor FLA Total Unit FLA Min Circuit Amp Max Fuse/ HACR Reheat Pump FLA Total Unit FLA Min Circuit Amp Max Fuse/ HACR 9.0 48.0 3.9 12.9 15.2 20 0.8 13.7 16.0 20 8.4 40.0 3.2 11.6 13.7 20 0.7 12.3 14.4 20 1 12.8 60.0 3.9 16.7 19.9 30 0.
PAGE 53
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Electrical Data – PSC Motor & Secondary Pump All TS Units with Standard PSC Motor Model 006 009 012 018 024 030 036 042 048 060 070 Voltage Code Rated Voltage Voltage Min/ Max QTY RLA G 208-230/60/1 197/254 1 3.1 TS Units with PSC Fan Motor and Secondary Pump TS Units (PSC) LRA Fan Motor FLA Total Unit FLA Min Circuit Amp Max Fuse/ HACR Pump FLA Total Unit FLA Min Circuit Amp Max Fuse/ HACR 17.7 0.4 3.5 4.3 15 0.43 3.9 4.
PAGE 54
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Electrical Data – High Static PSC Motor & Secondary Pump All TS Units with High Static PSC Fan Motor Model 018 024 030 036 042 048 060 Voltage Code Rated Voltage Voltage Min/ Max QTY RLA G 208-230/60/1 197/254 1 E 265/60/1 239/292 1 G 208-230/60/1 197/254 E 265/60/1 239/262 H 208-230/60/3 197/254 TS (H.S. PSC) Units TS Units with H.S.
PAGE 55
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Electrical Data – ECM Motor & Secondary Pump All TS Units with ECM Fan Motor Model 018 024 030 036 042 048 060 070 Voltage Min/Max TS Units (ECM) Fan Motor FLA Total Unit FLA 48.0 3.9 12.9 40.0 3.2 11.6 Compressor Max Fuse/ HACR Pump FLA 15.2 20 0.43 13.3 15.6 20 13.7 20 0.7 12.3 14.4 20 19.9 30 0.43 17.1 20.3 30 16.8 25 0.7 14.8 17.5 25 13.9 20 0.43 12.3 14.3 20 7.2 8.2 15 0.7 7.9 8.9 15 17.4 20.
PAGE 56
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P TS Series Wiring Diagram Matrix Only CXM and DXM diagrams, with a representative diagram of LON and MPC Options are presented in this submittal. Other diagrams can be located online at climatemaster.com using the part numbers presented below.
PAGE 57
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Typical Wiring Diagram – Single Phase TS Units with CXM Controller ClimateMaster works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice and may not be as described herein. Please contact ClimateMaster's Customer Service Department at 1-405-745-6000 for specific information on the current design and specifications.
PAGE 58
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Typical Wiring Diagram – Three Phase TS Units with DXM Controller ClimateMaster works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice and may not be as described herein. Please contact ClimateMaster's Customer Service Department at 1-405-745-6000 for specific information on the current design and specifications.
PAGE 59
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Typical Wiring Diagram – Three Phase TS Units with CXM Controller and ECM Blower ClimateMaster works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice and may not be as described herein. Please contact ClimateMaster's Customer Service Department at 1-405-745-6000 for specific information on the current design and specifications.
PAGE 60
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Typical Wiring Diagram – Single Phase TS Units with CXM, MPC, and ECM Controller ClimateMaster works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice and may not be as described herein. Please contact ClimateMaster's Customer Service Department at 1-405-745-6000 for specific information on the current design and specifications.
PAGE 61
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Typical Wiring Diagram – Single Phase TS Units with ClimaDry® II and ECM Blower ClimateMaster works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice and may not be as described herein. Please contact ClimateMaster's Customer Service Department at 1-405-745-6000 for specific information on the current design and specifications.
PAGE 62
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Tranquility® 20 (TS) Series 60Hz Engineering Specifications – Page 1 General: Furnish and install ClimateMaster Tranquility® “TS” Water Source Heat Pumps, as indicated on the plans. Equipment shall be completely assembled, piped and internally wired. Capacities and characteristics as listed in the schedule and the specifications that follow.
PAGE 63
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Tranquility® 20 (TS) Series 60Hz Engineering Specifications – Page 2 Cabinets shall have separate holes and knockouts for entrance of line voltage and low voltage control wiring. All factory-installed wiring passing through factory knockouts and openings shall be protected from sheet metal edges at openings by plastic ferrules.
PAGE 64
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Tranquility® 20 (TS) Series 60Hz Engineering Specifications – Page 3 Hermetic compressors shall be internally sprung. The compressor shall have a dual level vibration isolation system. The compressor will be mounted on specially engineered sound-tested EPDM vibration isolation grommets to a large heavy gauge compressor mounting plate, which is then isolated from the cabinet base with rubber grommets for maximized vibration attenuation.
PAGE 65
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Tranquility® 20 (TS) Series 60Hz Engineering Specifications – Page 4 Option: Units shall be supplied with factory installed non-fused electrical service disconnect switch. Solid State Control System (CXM): Units shall have a solid-state control system. Units utilizing electro-mechanical control shall not be acceptable.
PAGE 66
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Tranquility® 20 (TS) Series 60Hz Engineering Specifications – Page 5 h. i. j. k. l. m. n. o. Ability to work with heat pump thermostats using O or B reversing valve control. Emergency shutdown contacts. Boilerless system heat control at low loop water temperature. Ability to allow up to 3 units to be controlled by one thermostat. Relay to operate an external damper. Ability to automatically change fan speed from multistage thermostat.
PAGE 67
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Tranquility® 20 (TS) Series 60Hz Engineering Specifications – Page 6 a. b. c. d. e. f. g. h. i. j. k. l. m. n. o. p. q. r.
PAGE 68
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Tranquility® 20 (TS) Series 60Hz Engineering Specifications – Page 7 Thermostats: The thermostat shall be a ClimateMaster mechanical or electronic type thermostat as selected below with the described features: a. Single Stage Standard Manual Changeover (ATM11C11) Thermostat shall be a single-stage, horizontal mount, manual changeover with HEAT-OFF-COOL system switch and fan ONAUTO switch. Thermostat shall have a mechanical temperature set point indicator.
PAGE 69
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Tranquility® 20 (TS) Series 60Hz Engineering Specifications – Page 8 g. Multistage Automatic or Manual Changeover Programmable 7 Day with Humidity Control (ATP32U04) Thermostat shall be 7 day programmable (with up to 4 set points per day), multi-stage (3H/2C), automatic or manual changeover with HEAT-OFF-COOL-AUTO-EM HEAT system settings and fan ON-AUTO settings.
PAGE 70
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Notes: ClimateMaster works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice and may not be as described herein. Please contact ClimateMaster's Customer Service Department at 1-405-745-6000 for specific information on the current design and specifications.
PAGE 71
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Notes: ClimateMaster works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice and may not be as described herein. Please contact ClimateMaster's Customer Service Department at 1-405-745-6000 for specific information on the current design and specifications.
PAGE 72
TS Series 60Hz - HFC-410A Submittal Data Eng/I-P Revision Log Date: 7/17/13 02/26/13 01/07/13 09/27/12 02/20/12 02/02/12 12/14/11 11/02/11 10/19/11 08/09/11 08/03/11 06/17/11 05/16/11 04/07/11 02/11/11 01/03/11 09/29/10 09/28/10 09/07/10 09/01/10 08/24/10 07/26/10 07/26/10 06/11/10 06/11/10 06/01/10 03/30/10 05/27/09 04/29/09 04/29/09 11/17/08 09/19/08 08/26/08 08/01/08 08/0407 05/14/07 04/19/07 04/19/07 12/14/06 11/16/06 11/16/06 11/16/06 11/19/06 11/19/06 07/19/06 07/19/06 07/19/06 12/23/05 11/30/05 11/