User Manual

ManualsBrandsClimaCool ManualsEquipmentUCW_H 30, 50, 70, 85

www.climacoolcorp.com

Electrical Data UCW

Rated Min.Cir. MaxFuse Rec. Discon. Rated Min.Cir. Locked MaxFuse Rec.

Load Amps Size Fuse Switch Load Amps Rotor Size Fuse

Amps

(MCA)

(MOP)

3, 4

Size

4,5

Size

Amps

(MCA)

(LRA)

(MOP)

Size

UCW030AHASASB0S

208-230/3/60 85 96 125 110 150 42.7 53.3 425 90 70

UCW030AFASASB0S

460/3/60 39 43 60 50 70 19.3 24.1 187 40 30

UCW030ANASASB0S

575/3/60 31 35 50 40 50 15.4 19.3 148 30 25

UCW050AHASASB0S

208-230/3/60 147 166 225 200 225 73.7 92.1 500 150 125

UCW050AFASASB0S

460/3/60 67 75 100 90 100 33.3 41.7 250 70 60

UCW050ANASASB0S

575/3/60 53 60 80 70 80 26.7 33.3 198 50 45

UCW070AHASASB0S

208-230/3/60 190 214 300 250 300 95.1 118.9 600 200 150

UCW070AFASASB0S

460/3/60 86 97 125 110 150 43.0 53.8 310 90 70

UCW070ANASASB0S

575/3/60 69 77 110 90 110 34.4 43.0 255 70 60

UCW085AHASASB0S

208-230/3/60 225 253 350 300 350 112.4 140.5 732 250 175

UCW085AFASASB0S

460/3/60 102 115 150 150 175 50.8 63.5 368 110 80

UCW085ANASASB0S

575/3/60 82 92 125 110 125 40.7 50.8 292 90 70

Notes:

7. LRA - Locked Rotor Amps are instantaneous starting amperage per compressor.

Power Wiring - per Module

UCW030

UCW050

UCW070

4. MOP Device or Recommended Fusing Device for Module Power Wiring supplied by others. These are recommended values for electrical power protection of modules selected.

Internal Wiring - per Compressor

6. Disconnect Switch for Module Power Wiring supplied by others. These are recommended values for electrical power protection of modules selected.

Model

Type

Model #

Voltage

5. Recommended Dual Element Fuse Sizing: Rounded up from 150% of the RLA of the largest compressor motor plus 100% of the RLA of all other concurrent electrical loads.

UCW085

575V / 60 Hz: Min. 518V Max. 632V

8. Module internal wiring is per NEC.

9. Voltage Tolerance Range:

208-230V / 60 Hz: Min. 187V Max. 253V

460V / 60 Hz: Min. 414V Max. 506V

2. MCA - Minimum Circuit Ampacity is: 125% of the RLA of the largest compressor motor plus 100% of the RLA of all other concurrent motors and/or electrical loads.

1. RLA - Rated Load Amps are calculated as per UL1995.

3. MOP - Maximum Overcurrent Protected Device Amp Size is rounded down from: 225% of the RLA of the largest compressor motor plus 100% of the RLA of all other concurrent electrical loads.