Manual

29
www.climacoolcorp.com
®
Start Up and Warranty Registration Form
Start-Up (Air-Cooled)0308 .doc
Project Name: _________________________________ Start-Up Date: __________________
Address: ____________________________________________________________________
Module #: _______________ Model #: _________________ Serial Number: _______________________
Chiller # ________ Bank # _________ On-Site Location: ____________________________________
Evaporator 6” Main Inlet Pressure _______ Evaporator 6” Main Outlet Pressure _______ delta P_______
Evaporator “flow device” shut off chiller below approx. 40% loss of flow _________
Water Sample taken (Mark “X”) Evaporator ___
Water sample bottles are provided. Follow instructions on label and mail same day sample is taken, if possible.
All wiring terminations in module panel, safeties and compressors tightened _____
Voltage / Ground L1 ________ L2 ________ L3 ________
Phase / Phase L1/ L2 ________ L2/ L3 ________ L1/ L3 ________
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Circuit # 1 Refrigerant Type: (circle one) R-22 R-407C Field Charge (lbs)_________
Amperage L1 ________ L2 ________ L3 ________
________ leveL liO ssalG thgiS Comments: __________________________
Suction Pressure (PSIG) ________ ____________________________________
Suction Temperature (°F) ________ ____________________________________
Discharge Pressure (PSIG) ________ ____________________________________
Discharge Temperature (°F) ________ ____________________________________
Compressor Superheat (°F) ________ ____________________________________
Evaporator Entering Water Temperature (°F) ________ ____________________________________
Evaporator Leaving Water Temperature (°F) ________ ____________________________________
Condenser Entering Air Temperature (°F) ________ _________________
___________________
Condenser Leaving Air Temperature (°F) ________ ____________________________________
Condenser Entering Refrig. Liquid Temp (°F) ________ ____________________________________
Condenser Liquid Subcooling Temperature (°F) ________ ____________________________________
Evaporator Pressure Differential (PSIG) ________ ____________________________________
Verify Safety Settings: Low Limit_____ High Pressure Limit_____ Low Pressure Limit_____
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Circuit # 2 Refrigerant Type: (circle one) R-22 R-407C Field Charge (lbs)_________
Amperage L1 ________ L2 ________ L3 ________
________ leveL liO ssalG thgiS Comments: __________________________
Suction Pressure (PSIG) ________ ____________________________________
Suction Temperature (°F) ________ ____________________________________
Discharge Pressure (PSIG) ________ ____________________________________
Discharge Temperature (°F) ________ ____________________________________
Compressor Superheat (°F) ________ ____________________________________
Evaporator Entering Water Temperature (°F) ________ ____________________________________
Evaporator Leaving Water Temperature (°F) ________ ____________________________________
Condenser Entering Air Temperature (°F) ________ _______________
_____________________
Condenser Leaving Air Temperature (°F) ________ ____________________________________
Condenser Entering Refrig. Liquid Temp (°F) ________ ____________________________________
Condenser Liquid Subcooling Temperature (°F) ________ ____________________________________
Evaporator Pressure Differential (PSIG) ________ ____________________________________
Verify Safety Settings: Low Limit______ High Pressure Limit______ Low Pressure Limit______
NOTE: Correct rotation of scroll compressors is extremely critical. Incorrect rotation could damage the compressor.
___________________________
Contractor Name: ___________________________ __________________________________
Address: ___________________________
(Authorized Signature)
Phone: ___________________________ Date: _____________________________
Start-Up and Warranty Registration Form
(Air-Cooled)
Sign & date and fax: [phone] Attn.: Technical Services
Or E
-
mail:
[e-mail]
®