OME2208061
1 21 21 14 3 19 20 7 2 8 5 20 9 14 16 K 300mm K1 35PCS C 35PCS 8*40 22PCS 17 15 10 B 15 17 13 18 4 A 18 11 6 16 L M 3*12 F 10PCS 3.5*35 12 LED K2 D 2PCS 3.5*14 26PCS E 10PCS 3.
1 2 2000*334 1PS 6 3 1400*334 1PS 7 218*334 1PS 1400*334 1PS 8 218*334 1PS 12 11 4 5 434*334 1PS 9 218*320 1PS 13 434*334 1PS 10 2000*80 1PS 14 370*80 1PS 15 300*120 2PS 16 370*80 1PS 17 697*248 1PS 18 284*60 2PS 697*248 1PS 19 630*294 2PS 620*120 2PS 20 1378*228 1PS 300*120 2PS 21 330*276 2PS 166*334 2PS
Ｈａｒ ｄｗａｒ ｅ ｉ ｎｓｔ ａｌ ｌ ａｔ ｉ ｏｎ ｄｅｍｏｎｓｔ ｒ ａｔ ｉ ｏｎ ＮＯＴＥ： Ｐｌ ｅａｓｅ ｍａｋｅ ｓｕｒ ｅ ＂Ａ＂ｈａｒ ｄｗａｒ ｅ ｔ ｉ ｇｈｔ ｅｎｅｄ ａｎｄ ｃａｎ＇ ｔ ｂｅ ｐｕｌ ｌ ｅｄ ｏｕｔ ！ Ⅰ Ⅲ Ⅱ Ⅳ Scan QR code f or assembl y vi deo
① A A A A A A 2 A A C A A 1 A A A C C A A C A A A C A 11 C C 5 10 C C A A A C*12 C C 9 A A*23 4 C C A put A on board put C on board 1 2 9 10 11 1 9
② A 13 A A A A A C 21 A 12 C rotate K1 D 8 C 18 0° X2 A K1 A D 8 C 14 7 C 6 C A*12 C X2 A A A K1 D K1 D C K1 D C C*10 D*8 K1*4 put A on board put C on board 12 13 14 6 7 8 21
③ 21 G 2 21 G G G G G*4
④ 7 G G 8 G 3 6 G G 7 G G H E 8 H E H E 6 H E E*10 G*6 H*5 3 H E H E
⑤ 19 7 8 3 21 6 7 2 B 21 B 8 B 6 3 B B Make sure the arrow on the screw align to the hole on the side.
⑥ B 5 1 21 B 8 B 3 B 4 B*8 7 2 B 21 B 6 Make sure the arrow on the screw align to the hole on the side.
⑦ 11 9 B 11 10 B 1 B B B B 9 3 B 4 B B 10 Make sure the arrow on the screw align to the hole on the side.
⑧ B 18 16 B B 12 17 B 15 B 13 F B F F B F 14 18 12 15 12 16 F F 13 14 16 13 D K2 1 13 B*12 K2 4 12 D D*8 F*8 K2*4 put B on board 15 16
⑨ L M 4 1 2 19 5 4 E 1 2 19 5 7 7 20 I I I*8 L*10 M*10
⑩ 4 D J 1 19 5 LE D D*10 J*10 LED
11
LED Light If you can’t let the lights work successfully, please check the following: 1. Please check the direction of the connect, try it in the opposite direction, according to the following picture. 2. Please check the remote control, it need you to tear down the plastic septum before use it. 3. Don’t let the remote control too far from the receiver, make sure there is no obstruction between them.
