Instructions / Assembly

3
ELECTRICAL SPECIFICATIONS
Voltage:120VAC 60Hz
Watts:1400 Watts
Cold climate installation recommendation:
When installing this unit against a Non-insulated
exterior wall or chase, it is mandatory that outer walls
be insulated to conform to applicable insulation codes.
ELECTRICAL CONNECTION
The unit comes standard with 6 feet (1.8M) three wire cord, exiting from the rear of the
fireplace.
Plan the installation to avoid the use of an extension cord.
CLEANING TRIM
Clean the metal trim using a soft cloth, slightly dampened with citrus oil based product and
buff with a clean soft cloth.
DO NOT use brass polish or household cleaners as these products will damage the metal
trim, Citrus oil based products can be obtained at supermarkets or hardware stores.
MAINTENANCE
The motors used on the fan and the flame generator assembly are pre-lubricated for
extended bearing life and require no further lubrication. However, periodic
cleaning/vacuuming of the fan/heater unit is recommended. Make sure the unit is turn OFF
and unplugged whenever you are cleaning the heater of fireplace.
WARNING: Make sure the power is turned off before proceeding. Any electrical
repairs or rewiring of this unit should be carried out by a licensed electrician in
accordance with national and locate codes. If repairing or replacing any electrical
component or wiring, the original wire routing, color coding and securing locations
must be followed.
WARNING: Electric outlet wiring must comply with local building codes and other
applicable regulations to reduce risk of fire, electric shock and injury to persons.
WARNING: Do not use this fireplace if any part of it has been under water.
Immediately call a qualified service technician to inspect the fireplace and replace
any part of the electrical system.
WARNING: Disconnect power before attempting any maintenance or cleaning
to reduce the risk of fire, electrical shock or personal injury.
WARNING: During any service of this appliance, the power to the unit must be
turned off, Always remember to remove the electrical plug from the wall outlet.
12
TEMPORIZADOR
EI TEMPORIZADOR tiene configuraciones ajustables entre 30 minutos a 6 horas y una
posición OFF, como se muestra en el siguiente: 30 minutos-1h-2h-3h-4h-5h-6h-OFF. Si
la pantalla digital se enciende y no pasa nada dentro de 10 segundos, la pantalla digital
se apagará automaticamente.Una vez que el temporizador se ha seleccionado y el
tiempo se ha acabado, todas las funciones se cerrarán, y se entrará al modo de espera.
En este modo, usted debe tocar el botón de POWER para reiniciar el aparato.
BOTÓN AUMENTAR/DISMINUIR
Con el calentador encendido, presione el botón Aumentar o Disminuir para cambiar la
temperatura. Hay 11 opciones de temperatura: 72℉-74℉-76℉-78℉-80℉-82℉-ON-
64℉---72℉(22℃-23℃-24℃-25℃-26℃-27℃-ON-18℃---22℃).
La función del cambio de temperatura: cuando el calefactor está en la posición ON, pulse
y mantenga pulsado el botón de POWER por 5 segundos, la muestra de la temperatura
actual se destellará 3 veces y se convertirá a otra selección de temperatura (Nota: esto
no se puede ajustar con el mando a distancia).
La función de bloquear y desbloquear el calefactor: pulse y mantenga pulsado el botón por
10 segundos, las brasas se destellarán 6 veces, lo que indica que la función de calefactor
está cerrada. Para desbloquear la función de calefactor, pulse y mantenga pulsado el
botón CALEFACTOR por 10 segundos de nuevo, entonces las brasas también se
destellarán 6 veces, indicando la función de calefactor está desbloqueado a recuperar el
estado original que has seleccionado.(Nota: esto no se puede ajustar con el mando a
distancia).