SmartWindows4 installation guide © 2005 Directed Electronics, Vista, CA N903010 10-05
IMPORTANT! Please note that this manual was intended for US consumers and therefore includes American phrases or words. Bitwriter™, Code Hopping™, Directed®, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, NiteLite®, Nuisance Prevention® Circuitry, NPC®, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered Trademarks of Directed Electronics, Vista, California. 2 www.directed.
contents warning! safety first . . . . . . . . . . .5 wiring reference section . . . . . . .10 install the smartwindows 4 acces- tips for adding smartwindows4 sory . . . . . . . . . . . . . . . . . . . . . . . . .5 to systems . . . . . . . . . . . . . . . . . . .12 motor/switch connections . . . . . . .5 notes . . . . . . . . . . . . . . . . . . . . . . .15 .. Motor/Switch Connections Negative Switches . . . . . . . . . . . . .6 Program the Windows . . . . . . . . .7 window control . . . . . . . .
www.directed.
NOTE: If you can close the vehicle’s windows by turning the key in the door, SmartWindows 4 will not operate properly. Refer to the “Window Control” section of this manual. install the smartwindows 4 accessory NOTE: Refer to the Wiring Quick Reference Diagram at the back of this manual for the following instructions. 1. Connect one end of the CliffNet Dataport Interconnect cable to the alarm system control unit and connect the other end into the SmartWindows 4 module. 2.
b. 5. 6. 7. Connect the ORANGE wire to the motor side of the cut wire and the WHITE/ORANGE wire to the switch side. Find the wire that shows 12V while pressing the driver’s window switch as if rolling the window down on the driver’s side. a. If the voltmeter reads 12 volts while pressing DOWN side of the switch, cut this wire. b. Connect the BLUE wire to the window motor side of the cut line and the WHITE/BLUE wire to the switch side.
this wire. b. 5. 6. Find the wire that shows 12V while pressing the driver’s window switch as if roll ing the window down on the driver’s side. a. If the voltmeter reads 12V while pressing DOWN side of the switch, cut this wire. b. Connect the ORANGE wire to the window motor side of the cut line and the WHITE/ORANGE wire to the switch side. b. Connect the GRAY wire to the motor side of the switch and the WHITE/GRAY wire to the passenger’s switch side of the cut line.
4. Release the switch and allow the window to roll up. After the window reaches the top, it will pause. It will then automatically complete programming by rolling both windows up/down several times. 5. Programming is complete when both windows vent. You may then turn off the key to exit programming or if you have a second set of SmartWindows 4 installed, touch and release the driver’s window UP for the second set of windows. It will follow the same process as the first set you programmed.
7. Set the timer duration to proper time interval with 2-seconds added to that time interval. section 2—window rollup NOTE: This may require the use of an optional relay(s). The instructions in this section apply to systems with the built-in window roll up feature. If the windows can be closed using a key in the door of the car, see section 1 above. motor/switch connections 1. Turn the ignition switch to the “ON” position. 2. Access the wires at the window switch. 3.
wiring reference section window control—wiring tips 10 www.directed.
quick wiring reference diagram—window control © 2005 directed electronics—all rights reserved 11
tips for adding smartwindows4 to systems This section will assist when installing SmartWindows 4 with any of the following listed systems. If doing so, it will be necessary to use the CliffNet Wizard Prosoftware. AvantGuard 4 Concept 600 IntelliGuard 9000 or IntelliGuard Millennia If using SmartWindows4 WITH the system’s window rollup electronics: control the rear windows. When installation is complete: 1.
11. Click done. 12. Click OK to save and exit or Apply to save and test/adjust vent duration. If using SmartWindows 4 INSTEAD OF the system’s window rollup electronics: Install the SmartWindows 4 module(s). When installation is complete: 1. Plug the Wizard cable into any available 3-pin DataPort connection in the installation (on SmartWindows 4, for example). 2. Launch the CliffNet Wizard PRO program. 3. Click the Install icon button at the top of the screen. 4.
www.directed.
notes ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ________________________________________ ______________
