Service manual
Table Of Contents
- Manual
- Preface
- Chapter 1: Introduction
- Overview
- Specifications
- External Locator - Top View with LCD Panel Open
- External Locator - Front & Right Side Views
- External Locator - Left Side & Rear View
- External Locator - Bottom View
- Mainboard Overview - Top (Key Parts)
- Mainboard Overview - Bottom (Key Parts)
- Mainboard Overview - Top (Connectors)
- Mainboard Overview - Bottom (Connectors)
- Chapter 2: Disassembly
- Overview
- Maintenance Tools
- Connections
- Maintenance Precautions
- Disassembly Steps
- Removing the Battery
- Removing the Keyboard
- Removing the Hard Disk Drive
- Removing the Optical (CD/DVD) Device
- Removing the System Memory (RAM)
- Removing and Installing a Processor
- Removing the Fan Unit
- Removing the Wireless LAN Module
- Removing the MSATA Module
- Removing the CCD
- Appendix A: Part Lists
- Appendix B: Schematic Diagrams
- System Block Diagram
- Processor 1/7-DMI, FDI, PEG
- Processor 2/7- CLK, MISC
- Processor 3/7- (DDR3)
- Processor 4/7- Power
- Processor 5/7- GFX PWR
- Processor 6/7- GND
- Processor 7/7- RSVD
- DDR3 SO-DIMM_1
- DDR3 SO-DIMM_2
- PS8625
- PANEL, INVERTER
- VGA PCI-E Interface
- VGA Frame Buffer Interface
- VGA Frame Buffer A
- VGA Frame Buffer C
- VGA I/O
- VGA NVVDD Decoupling
- CRT, Holes
- Lynx 1/9
- Lynx 2/9
- Lynx 3/9
- Lynx 4/9
- Lynx 5/9
- Lynx 6/9
- Lynx 7/9
- Lynx 8/9
- Lynx 9/9
- 3G, WLAN, PCIE, CON
- USB Charge, CCD, TPM, Power Con
- eSATA/USB3.0, LED
- Card Reader (RTL8411)
- HDD, TP, Audio, USB
- HDMI, RJ45, Fan, KBC, LED
- AUDIO CODEC VT1802S
- KBC-ITE IT8587
- 5VS, 3VS, 3.3VM, 5VM
- 1.05V
- VDD3, VDD5
- 1.5V or 1.35V / 0.75VS, 1.5VS
- POWER VCORE
- N14P, NVVDD, PEX, FBVDDQ
- AC IN, CHARGER
- AUDIO BOARD
- POWER SWITCH BOARD
- ODD to HDD BOARD
- Appendix C: Updating the FLASH ROM BIOS

Preface
V
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This
is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
3. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save
your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or mois-
ture may affect the system.
Don’t use or store the com-
puter in a humid environment.
Do not place the computer on
any surface which will block
the vents.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
Do not disassemble the com-
puter by yourself.
Perform routine maintenance
on your computer.