Service manual
Table Of Contents
- Manual
- Preface
- Chapter 1: Introduction
- Overview
- Specifications
- External Locator - Top View with LCD Panel Open
- External Locator - Front & Right Side Views
- External Locator - Left Side & Rear View
- External Locator - Bottom View
- Mainboard Overview - Top (Key Parts)
- Mainboard Overview - Bottom (Key Parts)
- Mainboard Overview - Top (Connectors)
- Mainboard Overview - Bottom (Connectors)
- Chapter 2: Disassembly
- Overview
- Maintenance Tools
- Connections
- Maintenance Precautions
- Disassembly Steps
- Removing the Battery
- Removing the Keyboard
- Removing the Hard Disk Drive
- Removing the Optical (CD/DVD) Device
- Removing the System Memory (RAM)
- Removing and Installing a Processor
- Removing the Fan Unit
- Removing the Wireless LAN Module
- Removing the MSATA Module
- Removing the CCD
- Appendix A: Part Lists
- Appendix B: Schematic Diagrams
- System Block Diagram
- Processor 1/7-DMI, FDI, PEG
- Processor 2/7- CLK, MISC
- Processor 3/7- (DDR3)
- Processor 4/7- Power
- Processor 5/7- GFX PWR
- Processor 6/7- GND
- Processor 7/7- RSVD
- DDR3 SO-DIMM_1
- DDR3 SO-DIMM_2
- PS8625
- PANEL, INVERTER
- VGA PCI-E Interface
- VGA Frame Buffer Interface
- VGA Frame Buffer A
- VGA Frame Buffer C
- VGA I/O
- VGA NVVDD Decoupling
- CRT, Holes
- Lynx 1/9
- Lynx 2/9
- Lynx 3/9
- Lynx 4/9
- Lynx 5/9
- Lynx 6/9
- Lynx 7/9
- Lynx 8/9
- Lynx 9/9
- 3G, WLAN, PCIE, CON
- USB Charge, CCD, TPM, Power Con
- eSATA/USB3.0, LED
- Card Reader (RTL8411)
- HDD, TP, Audio, USB
- HDMI, RJ45, Fan, KBC, LED
- AUDIO CODEC VT1802S
- KBC-ITE IT8587
- 5VS, 3VS, 3.3VM, 5VM
- 1.05V
- VDD3, VDD5
- 1.5V or 1.35V / 0.75VS, 1.5VS
- POWER VCORE
- N14P, NVVDD, PEX, FBVDDQ
- AC IN, CHARGER
- AUDIO BOARD
- POWER SWITCH BOARD
- ODD to HDD BOARD
- Appendix C: Updating the FLASH ROM BIOS
Disassembly
2 - 20 Removing the CCD
2.Disassembly
Removing the CCD
1. Turn off the computer, turn it over, and remove the battery (page 2 - 14).
2. Run your fingers around the inner frame of the LCD panel at the points as indicated by the arrows - .
3. Lay the computer down on a flat surface with the top case up forming a 90 degree angle. Push the LCD front
cover upwards before carefully lifting it up.
4. Remove the LCD front cover (Figure 16c).
1
4
5
5
c.
b.
a.
1
5
5
3
2
4
5. LCD Front Cover
Figure 16
CCD Removal
a. Run your fingers around
the inner frame of the
LCD panel at the points
indicated by the arrows.
b. Lay the computer down
on a flat surface with the
top case up forming a 90
degree angle. Push the
LCD front panel upwards
before carefully lifting it
up.
c. Remove the LCD front
cover.