Service manual
Table Of Contents
- Manual
- Preface
- Chapter 1: Introduction
- Overview
- Specifications
- External Locator - Top View with LCD Panel Open
- External Locator - Front & Right Side Views
- External Locator - Left Side & Rear View
- External Locator - Bottom View
- Mainboard Overview - Top (Key Parts)
- Mainboard Overview - Bottom (Key Parts)
- Mainboard Overview - Top (Connectors)
- Mainboard Overview - Bottom (Connectors)
- Chapter 2: Disassembly
- Overview
- Maintenance Tools
- Connections
- Maintenance Precautions
- Disassembly Steps
- Removing the Battery
- Removing the Keyboard
- Removing the Hard Disk Drive
- Removing the Optical (CD/DVD) Device
- Removing the System Memory (RAM)
- Removing and Installing a Processor
- Removing the Fan Unit
- Removing the Wireless LAN Module
- Removing the MSATA Module
- Removing the CCD
- Appendix A: Part Lists
- Appendix B: Schematic Diagrams
- System Block Diagram
- Processor 1/7-DMI, FDI, PEG
- Processor 2/7- CLK, MISC
- Processor 3/7- (DDR3)
- Processor 4/7- Power
- Processor 5/7- GFX PWR
- Processor 6/7- GND
- Processor 7/7- RSVD
- DDR3 SO-DIMM_1
- DDR3 SO-DIMM_2
- PS8625
- PANEL, INVERTER
- VGA PCI-E Interface
- VGA Frame Buffer Interface
- VGA Frame Buffer A
- VGA Frame Buffer C
- VGA I/O
- VGA NVVDD Decoupling
- CRT, Holes
- Lynx 1/9
- Lynx 2/9
- Lynx 3/9
- Lynx 4/9
- Lynx 5/9
- Lynx 6/9
- Lynx 7/9
- Lynx 8/9
- Lynx 9/9
- 3G, WLAN, PCIE, CON
- USB Charge, CCD, TPM, Power Con
- eSATA/USB3.0, LED
- Card Reader (RTL8411)
- HDD, TP, Audio, USB
- HDMI, RJ45, Fan, KBC, LED
- AUDIO CODEC VT1802S
- KBC-ITE IT8587
- 5VS, 3VS, 3.3VM, 5VM
- 1.05V
- VDD3, VDD5
- 1.5V or 1.35V / 0.75VS, 1.5VS
- POWER VCORE
- N14P, NVVDD, PEX, FBVDDQ
- AC IN, CHARGER
- AUDIO BOARD
- POWER SWITCH BOARD
- ODD to HDD BOARD
- Appendix C: Updating the FLASH ROM BIOS
Disassembly
Removing the Hard Disk Drive 2 - 7
2.Disassembly
Removing the Hard Disk Drive
The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm
or 7mm (h). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as
outlined in Chapter 4 of the User’s Manual) when setting up a new hard disk.
Hard Disk Upgrade Process
Figure 3
HDD Assembly
Removal
a. Remove the screws. Lift
the component bay cov-
er off the computer.
3. Component Bay
Cover
•2 Screws
1. Turn off the computer, and remove the battery (page 2 - 5).
2. Locate the component bay cover and remove screws - (Figure 3a
).
3. Lift the component bay cover off the computer case by applying pressure at points & ; if you have prob-
lems using a finger to do this, then use a non-abrasive, non-sharp object (e.g. a coin) to lift the cover up before
removal).
1
2
3
4
5
1
3
a.
2
4
5