Service manual
Table Of Contents
- Manual
- Preface
- Chapter 1: Introduction
- Overview
- Specifications
- External Locator - Top View with LCD Panel Open
- External Locator - Front & Right Side Views
- External Locator - Left Side & Rear View
- External Locator - Bottom View
- Mainboard Overview - Top (Key Parts)
- Mainboard Overview - Bottom (Key Parts)
- Mainboard Overview - Top (Connectors)
- Mainboard Overview - Bottom (Connectors)
- Chapter 2: Disassembly
- Overview
- Maintenance Tools
- Connections
- Maintenance Precautions
- Disassembly Steps
- Removing the Battery
- Removing the Keyboard
- Removing the Hard Disk Drive
- Removing the Optical (CD/DVD) Device
- Removing the System Memory (RAM)
- Removing and Installing a Processor
- Removing the Fan Unit
- Removing the Wireless LAN Module
- Removing the MSATA Module
- Removing the CCD
- Appendix A: Part Lists
- Appendix B: Schematic Diagrams
- System Block Diagram
- Processor 1/7-DMI, FDI, PEG
- Processor 2/7- CLK, MISC
- Processor 3/7- (DDR3)
- Processor 4/7- Power
- Processor 5/7- GFX PWR
- Processor 6/7- GND
- Processor 7/7- RSVD
- DDR3 SO-DIMM_1
- DDR3 SO-DIMM_2
- PS8625
- PANEL, INVERTER
- VGA PCI-E Interface
- VGA Frame Buffer Interface
- VGA Frame Buffer A
- VGA Frame Buffer C
- VGA I/O
- VGA NVVDD Decoupling
- CRT, Holes
- Lynx 1/9
- Lynx 2/9
- Lynx 3/9
- Lynx 4/9
- Lynx 5/9
- Lynx 6/9
- Lynx 7/9
- Lynx 8/9
- Lynx 9/9
- 3G, WLAN, PCIE, CON
- USB Charge, CCD, TPM, Power Con
- eSATA/USB3.0, LED
- Card Reader (RTL8411)
- HDD, TP, Audio, USB
- HDMI, RJ45, Fan, KBC, LED
- AUDIO CODEC VT1802S
- KBC-ITE IT8587
- 5VS, 3VS, 3.3VM, 5VM
- 1.05V
- VDD3, VDD5
- 1.5V or 1.35V / 0.75VS, 1.5VS
- POWER VCORE
- N14P, NVVDD, PEX, FBVDDQ
- AC IN, CHARGER
- AUDIO BOARD
- POWER SWITCH BOARD
- ODD to HDD BOARD
- Appendix C: Updating the FLASH ROM BIOS

Disassembly
2 - 4 Disassembly Steps
2.Disassembly
Disassembly Steps
The following table lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM
THE DISASSEMBLY STEPS IN THE ORDER INDICATED.
To remove the Battery:
1. Remove the battery page 2 - 5
To remove the Keyboard:
1. Remove the battery page 2 - 5
2. Remove the keyboard page 2 - 6
To remove the HDD:
1. Remove the battery page 2 - 5
2. Remove the HDD page 2 - 7
To remove the Optical Device:
1. Remove the battery page 2 - 5
2. Remove the Optical device page 2 - 10
To remove the System Memory:
1. Remove the battery page 2 - 5
2. Remove the system memory page 2 - 12
To remove and install a Processor:
1. Remove the battery page 2 - 5
2. Remove the processor page 2 - 14
3. Install the processor page 2 - 16
To remove the Wireless LAN Module:
1. Remove the battery page 2 - 5
2. Remove the WLAN page 2 - 18
To remove the MSATA Module:
1. Remove the battery page 2 - 5
2. Remove the MSATA page 2 - 19
To remove the CCD Module:
1. Remove the battery page 2 - 5
2. Remove the CCD module page 2 - 20