Instruction manual

ManualsBrandsClek ManualsAutomotiveOobr

0 000002 8

Oobr Instruction Manual

This belt-positioning booster seat (booster seat) is designed for use in either full back mode

or backless mode by children who meet all of the following requirements:

JULY2013

WARNING

t3&"%"/%6/%&345"/%130%6$5-"#&-4"/%"--*/4536$5*0/4*/5)*4

."/6"-"/%*/:0637&)*$-&08/&34."/6"-#&'03&*/45"--*/(03

64*/(5)*4#0045&34&"5

t'"*-63&501301&3-:*/45"--0364&5)*4#0045&34&"503'0--085)&4&

8"3/*/(4"/%5)04&0/5)*4#0045&34&"54-"#&-4$"/3&46-5*/

4&3*064*/+63:03%&"5)505)&$)*-%*/"4)"31563/46%%&/4501

03$3"4)

)FJHIU 8FJHIU 3FDPNNFOEFE"HF

40 –57 in.

101–145 cm.

40–100 lb.

18–45 kg.

4 years & up

)FJHIU 8FJHIU 3FDPNNFOEFE"HF

38 –57 in.

96–145 cm.

33–100 lb.

15–45 kg.

4 years & up

Summary of content (36 pages)

PAGE 1
0 000002 8 Oobr Instruction Manual This belt-positioning booster seat (booster seat) is designed for use in either full back mode or backless mode by children who meet all of the following requirements: )FJHIU 8FJHIU 3FDPNNFOEFE "HF 38 –57 in. 96–145 cm. 33–100 lb. 15–45 kg. 4 years & up )FJHIU 8FJHIU 3FDPNNFOEFE "HF 40 –57 in. 101–145 cm. 40–100 lb. 18–45 kg. 4 years & up WARNING t 3&"% "/% 6/%&345"/% 130%6$5 -"#&-4 "/% "-- */4536$5*0/4 */ 5)*4 ."/6"- "/% */ :063 7&)*$-& 08/&3 4 .
PAGE 2
Checklist for Proper Use This is only a checklist — you must read and understand all of the warnings and instructions on this booster seat’s labels and in this manual before installing or using this booster seat. When Using This Booster Seat in Full Back Mode (with Seat Back) √ Child weighs between 33 and 100 lb. (15 and 45 kg.), height is between 38 and 57 in. (96 to 145 cm.
PAGE 3
Table of Contents Checklist for Proper Use .......................................................................................... i When Using This Booster Seat in Full Back Mode (with Seat Back) .......................... i When Using This Booster Seat in Backless Mode (without Seat Back) ......................ii Booster Seat Features............................................................................................. 3 Registration & Recall Information .........................................
PAGE 4
Booster Seat Features Registration & Recall Information 10 Instruction Manual (store in compartment under seat) 1 LATCH Connectors 2 Recline Handle 3 Seat Cushion 4 Cup Holder (drink-thingy™) 5 Armrests 6 Seat Back Release Strap (to remove Seat Back for backless mode) 7 Seat Back (for full back mode) 8 Headrest 9 Headrest Adjuster WARNING 11 Lap Belt Guides 12 Shoulder Belt Guides t $)*-% 3&453"*/54 $06-% #& 3&$"--&% '03 4"'&5: 3&"40/4 :06 .
PAGE 5
Registering Your Booster Seat Please fill in the information on the previous page for your records. The model name, serial number and manufacturing date can be found on a label affixed to the underside of this booster Seat Base. Fill out the prepaid registration postcard attached to the seat and mail it today. Child restraints could be recalled for safety reasons. You MUST register this restraint (booster seat) to be reached in a recall.
PAGE 6
WARNING — DEATH or SERIOUS INJURY can occur (continued) t /&7&3 64& 8*5) 0/-: " -"1 #&-5 50 3&453"*/ " $)*-% */ 5)*4 #0045&3 SEAT. USE WITHOUT A LAP AND SHOULDER BELT CAN RESULT IN SERIOUS INJURY OR DEATH. t %0 /05 64& 5)*4 #0045&3 4&"5 8*5) .0503*;&% 03 %003 .06/5&% BELT SYSTEMS. t 4&$63& 5)*4 $)*-% 3&453"*/5 8*5) 5)& 7&)*$-& 4 $)*-% 3&453"*/5 ANCHORAGE SYSTEM IF AVAILABLE OR WITH A VEHICLE BELT.
PAGE 7
Certification t 5IJT CPPTUFS TFBU DPOGPSNT UP BMM BQQMJDBCMF 'FEFSBM .PUPS 7FIJDMF 4BGFUZ 4UBOEBSET and is certified for use in motor vehicles. t This booster seat is not certified for aircraft use because aircraft seats DO NOT have shoulder belts. Size & Age Limitations WARNING t '"*-63& 50 $)004& 5)& $033&$5 #0045&3 4&"5 .0%& '6-- #"$, 03 #"$,-&44 '03 :063 $)*-% 4 )&*()5 "/% 8&*()5 .
PAGE 8
When Using This Booster Seat in Backless Mode (without Seat Back) t 5IF UPQT PG UIF DIJME T FBST .645 CF CFMPX UIF UPQ PG this booster seat’s Headrest, as shown in Figure 1. If the tops of the ears are above the top of this booster seat’s Headrest in the highest adjustment position, your child is too large for using this booster seat in full back mode. t $IJME T XFJHIU JT CFUXFFO BOE MC (18 and 45 kg.), AND t $IJME T IFJHIU JT CFUXFFO BOE JO (101 and 145 cm.
PAGE 9
Vehicle Information Vehicle Seat Location Requirements Vehicle Child Restraint Anchorage System (LATCH) WARNING t -"5$) TUBOET GPS -PXFS "ODIPST BOE 5FUIFST GPS Children. These terms refer to the anchors built into a vehicle for attaching child restraints and consists of two lower anchors at the crease between the vehicle seat back and vehicle seat cushion and a top tether anchor behind the vehicle seat.
PAGE 10
Install this booster seat only on vehicle seats that face forward. NEVER install this booster seat on vehicle seats facing sideways or backwards, as shown in Figure 7. UNSAFE VEHICLE SEAT BELT SYSTEMS DO NOT USE ANY OF THE FOLLOWING VEHICLE SEAT BELT SYSTEMS WITH THIS BOOSTER SEAT: t /&7&3 VTF B MBQ POMZ CFMU BT TIPXO JO Figure 8. Figure 7 Figure 8 Only use this booster seat on vehicle seats with seat backs that lock in an upright position.
PAGE 11
Installing Booster Seat in Full Back Mode When Using LATCH Connectors Installing/Removing Booster Seat Using LATCH Connectors IMPORTANT: This booster seat is designed to be used with the vehicle’s LATCH Anchorage System. Always secure this booster seat to the vehicle’s LATCH Anchorage System, if available. If your vehicle does not have a LATCH Anchorage System, you can still use this booster seat. See “Installing Booster Seat WITHOUT Using LATCH Connectors” section of this manual on page 33.
PAGE 12
WARNING t %0 /05 64& 5)& -"5$) $0//&$5034 50 4&$63& 5)*4 #0045&3 4&"5 50 THE VEHICLE’S LATCH ANCHORAGE SYSTEM IF THE SEAT BELT OR SEAT BELT #6$,-& *4 /05 &"4*-: "$$&44*#-& 8*5) 5)*4 #0045&3 4&"5 -"5$)&% */ 1-"$& 03 *' 5)& 7&)*$-& 4&"5 #&-5 #6$,-& *4 -0$"5&% */ #&58&&/ 5)& LATCH ANCHORS, AS SHOWN IN FIGURE 12. OR IF THE VEHICLE SEAT BELT IS LOCATED IN BETWEEN THE LATCH ANCHORS, AS SHOWN IN FIGURE 13.
PAGE 13
IMPORTANT: If LATCH Connectors fail to connect to the vehicle’s LATCH lower anchors, you can still use this seat. See “Installing Booster Seat in Full Back Mode WITHOUT Using LATCH Connectors” section of this manual on page 34. Please notify Clek Customer Service if the LATCH Connectors fail to latch by calling 1-866-656-2462. Step 3.
PAGE 14
ADJUSTING THE SEAT BACK RECLINE (FULL BACK MODE WHEN USING LATCH CONNECTORS ONLY): WARNING To adjust to reclined position, pull on the Recline Handle located on the front of the Seat Base and slide this booster seat towards you to the desired recline position, as shown in Figure 20. Release Recline Handle to lock booster seat in the recline position. Make sure the booster seat Headrest remains in contact with the vehicle seat back or headrest.
PAGE 15
Removing Booster Seat in Full Back Mode When Using LATCH Connectors Installing Booster Seat in Backless Mode When Using Latch Connectors Step 1. Pull on the Recline Handle located on the front of the booster Seat Base and slide this booster seat towards you exposing the LATCH Connectors 1 , as shown in Figure 22. WARNING t 8)&/ */ #"$,-&44 .0%& 5)& #"$, 0' 5)*4 #0045&3 4&"5 #"4& .645 $0/5"$5 5)& 7&)*$-& 4&"5 #"$, 1 To remove Seat Back, see “Installing/Removing Seat Back” section on page 53.
PAGE 16
Locate the LATCH lower anchors, as shown in Figure 25. See “Vehicle Child Restraint Anchorage System (LATCH)” section of this manual on page 13 or refer to your vehicle owner’s manual. WARNING t %0 /05 64& -"5$) $0//&$5034 50 4&$63& 5)*4 #0045&3 4&"5 50 THE VEHICLE’S LATCH ANCHORAGE SYSTEM IF THE SEAT BELT OR SEAT BELT #6$,-& *4 /05 &"4*-: "$$&44*#-& 8*5) 5)*4 #0045&3 4&"5 -"5$)&% */ 1-"$& 03 *' 5)& 7&)*$-& 4&"5 #&-5 #6$,-& *4 -0$"5&% */ #&58&&/ 5)& LATCH ANCHORS, AS SHOWN IN FIGURE 26.
PAGE 17
To connect to lower anchors, pull and hold Recline Handle on front of booster Seat Base 1 and pull LATCH Connectors out 2 , as shown in Figure 28. 1 IMPORTANT: If LATCH Connectors fail to connect to the LATCH lower anchors, you can still use this seat. See section titled “Installing Booster Seat in Backless Mode WITHOUT Using LATCH Connectors” of this manual on page 36. However, please notify us if the LATCH Connectors fail to latch by calling 1-866-656-2462. Step 3.
PAGE 18
Removing Booster Seat in Backless Mode When Using LATCH Connectors Step 4. Complete installation by adjusting this booster seat so the back of this booster seat contacts the front of the vehicle seat back, as shown in Figure 30. Step 1. Figure 30 To adjust, pull and hold the Recline Handle on the front of this booster Seat Base 1 and push this booster seat towards the vehicle’s seat back 2 until the back of this booster seat sits firmly against the vehicle seat back, as shown in Figure 31.
PAGE 19
Installing Booster Seat WITHOUT Using LATCH Connectors WARNING t '"*-63& 50 1301&3-: */45"-- 03 64& 5)*4 #0045&3 4&"5 */$3&"4&4 5)& 3*4, 0' 4&3*064 */+63: 03 %&"5) 50 5)& $)*-% "/% 05)&34 */ " 4)"31 TURN, SUDDEN STOP OR CRASH. t 50 "70*% */+63: 5)*4 #0045&3 4&"5 .645 #& */45"--&% #: "/ "%6-5 t /&7&3 -&"7& 5)*4 #0045&3 4&"5 6/4&$63&% */ :063 7&)*$-& 5)*4 BOOSTER SEAT MUST REMAIN CONNECTED TO THE LATCH LOWER ANCHORS IN THE VEHICLE OR SECURED BY THE VEHICLE’S SEAT BELT EVEN WHEN NOT IN USE.
PAGE 20
Installing Booster Seat in Backless Mode WITHOUT Using LATCH Connectors Step 2. Center this booster seat on the vehicle seat and position this booster seat firmly against seat back with LATCH Connectors tucked into the crease between the vehicle seat back and vehicle seat cushion. To remove Seat Back, see “Installing/Removing Seat Back” section of this manual on page 53. Step 3. Step 1. Ensure that the booster Seat Base is in contact with the vehicle seat back, as shown in Figure 36.
PAGE 21
Securing Your Child in Booster Seat Step 2. Center this booster seat on the vehicle seat and position this booster seat firmly against seat back with LATCH Connectors tucked into the crease between the vehicle seat back and vehicle seat cushion. WARNING t 64& 0/-: " 7&)*$-& 4 -"1 "/% 4)06-%&3 #&-5 4:45&. 8)&/ RESTRAINING THE CHILD IN THIS BOOSTER SEAT. Step 3. Ensure that the booster Seat Base is in contact with the vehicle seat back, as shown in Figure 39. t 7&)*$-& -"1 "/% 4)06-%&3 #&-5 .
PAGE 22
When Using Booster Seat in Full Back Mode (with Seat Back): Height Weight Recommended Age 38 –57 in. 96–145 cm. 33–100 lb. 15–45 kg. 4 years & up Step 1. The child MUST sit in this booster seat with their back flat against the Seat Back, as shown in Figure 41. Figure 41 WARNING t %*4$0/5*/6& 64& 0' 5)*4 #0045&3 4&"5 */ '6-- #"$, .0%& *' 5014 0' CHILD’S EARS ARE ABOVE THE BOOSTER SEAT HEADREST IN THE HIGHEST "%+645.&/5 104*5*0/ 4&7&3& )&"% 03 /&$, */+63*&4 $06-% 3&46-5 WITHOUT PROPER HEAD SUPPORT.
PAGE 23
Step 3. Step 5. Pull the lap and shoulder belt over the child while positioning BOTH the lap and shoulder belt underneath the Armrest on the vehicle seat belt buckle side and buckle the seat belt, as shown in Figure 43. Adjust Headrest height. The bottom of the Shoulder Belt Guide should be at or above the top of the child’s shoulders, as shown in Figure 45. Figure 45 Figure 43 Step 4. The tops of the child’s ears MUST be below the top of this booster seat’s Headrest, as shown in Figure 46.
PAGE 24
IMPORTANT: If the shoulder belt is off the child’s shoulder, not centered on the child’s chest, or the ears are above the top of the headrest in the highest adjustment position, then your child is too large to use this booster seat in full back mode. Step 6. Pull on shoulder belt to remove all slack out of the lap and shoulder belt and snugly adjust the vehicle seat belt onto the child.
PAGE 25
ADJUSTING THE HEADREST: DO NOT use with the vehicle shoulder belt touching the child’s neck, as shown in Figure 52, or face, as shown in Figure 53. Step 1. With child sitting in this booster seat, have your child lean forward. Step 2. Figure 52 Figure 53 To avoid serious abdominal injury or death, a child MUST sit upright and not slouch in this booster seat, as shown in Figure 54.
PAGE 26
When Using Booster Seat in Backless Mode (without Seat Back): Height Weight Recommended Age 40 –57 in. 101–145 cm. 40–100 lb. 15–45 kg. 4 years & up Step 1. The child MUST sit in this booster seat with their back flat against the vehicle seat back, as shown in Figure 56. Figure 56 WARNING t %*4$0/5*/6& 64& 0' 5)*4 #0045&3 4&"5 */ #"$,-&44 .0%& *' 5014 0' 5)& $)*-% 4 &"34 "3& "#07& 5)& 7&)*$-& 4&"5 #"$, 03 )&"%3&45 */ 5)& )*()&45 "%+645.
PAGE 27
Step 3. Step 5. Position the lap belt underneath the Armrest on the side opposite the vehicle seat belt buckle, as shown in Figure 58. Pull on the shoulder belt to remove all slack out of the lap and shoulder belt and snugly adjust the vehicle seat belt onto the child. Figure 58 IMPORTANT: Design and operation of vehicle seat belt systems vary from vehicle to vehicle and from seating location to seating location within the same vehicle.
PAGE 28
IMPORTANT: If the shoulder belt is off the child’s shoulder, not centered on the child’s chest, or the ears are above the top of the vehicle seat back or headrest in the highest adjustment position, then your child is too large to use this booster seat in backless mode. t %0 /05 VTF XJUI UIF WFIJDMF TIPVMEFS CFMU UPVDIJOH UIF DIJME T OFDL BT TIPXO in Figure 65, or face, as shown in Figure 66, or off their shoulder, as shown in Figure 67.
PAGE 29
Installing/Removing Seat Back To Install the Seat Back: To Remove the Seat Back: Facing the back of the Seat Base, align the Seat Back legs in the openings in the Seat Base behind the Armrests, as shown in Figure 71. Step 1. Step 1. Facing the front of this booster seat, tilt this booster seat counter-clockwise, resting it on its side, as shown in Figure 69. Step 2. Locate the Seat Back Release Strap on the bottom right side of seat. Figure 71 Step 3. Step 2.
PAGE 30
Step 3. Installing/Removing Cup Holder (drink-thingy™) Press the left leg into the Seat Back lock (listen for audible click), as shown in Figure 73. To Install Cup Holder (drink-thingy™): Step 1. Remove Seat Cushion from Seat Base and set Seat Cushion to side. (See section titled “Removing/Installing Seat Cushion & Seat Cushion Cover,” on page 58.) Figure 73 Step 2. Locate Cup Holder slots on front corners of Seat Base, as shown in Figure 75. Figure 75 Step 3.
PAGE 31
To Remove Cup Holder (drink-thingy™): Step 1. Remove Seat Cushion from Seat Base and set Seat Cushion to side. (See section titled “Removing/Installing Seat Cushion & Seat Cushion Cover,” on page 58.) Care & Cleaning Removing/Installing Seat Cushion & Seat Cushion Cover Step 2. WARNING Holding onto the outside of the Cup Holder, slide Cup Holder tabs out of slots in Seat Base. Step 3. Install Seat Cushion back onto Seat Base.
PAGE 32
Step 4. To Install Seat Cushion Cover: Turn Seat Cushion over to locate the Seat Cushion Cover attachments, as shown in Figure 81. Step 1. Place Seat Cushion Cover on a flat surface with Seat Cushion Cover attachments facing up, as shown in Figure 84. Figure 81 Step 2. Place Seat Cushion into Seat Cushion Cover, aligning the seat cushion with the Seat Cushion Cover attachments. Step 5.
PAGE 33
Washing Instructions To Install Seat Cushion: Step 1. SEAT CUSHION COVER WASHING INSTRUCTIONS Place Seat Cushion onto top surface of Seat Base. Step 1. Once the Seat Cushion Cover is removed, set the foam pad aside. DO NOT wash foam pad. Step 2. Slide Seat Cushion rearward underneath Seat Back to align snaps in Seat Base, as shown in Figure 86. Step 3. Step 2. Follow washing instructions on wash tag located on inside of Seat Cushion Cover.
PAGE 34
SEAT BACK COVER & HEADREST COVER FABRIC WASHING INSTRUCTIONS SEAT FRAME (EXTERIOR PLASTICS ONLY) WASHING INSTRUCTIONS IMPORTANT: The booster Seat Back Cover and Headrest Cover are not removable for washing. Use a soft cloth with warm water and soap. Apply light pressure with cloth in small circular motions. Step 1. Accessories If the spot has dried, try lightly brushing or scraping off the residual. Wipe surface with water. Step 2.
PAGE 35
Warranty Warranty Limitations Limited Warranty This warranty does not cover the effects of normal wear and tear or damages resulting from negligence, modification, improper installation, accidents, misuse or abuse of this product. It is expressly agreed that the obligations of Clek Inc. and the original consumer purchaser’s remedies under the limited warranty contained herein are exclusive and are strictly limited to the repair or replacement of the product.
PAGE 36
,FFQ UIJT *OTUSVDUJPO .BOVBM GPS GVUVSF VTF Store in compartment on bottom of this booster seat. w w w.clekinc.com Clek Inc. 12 Upjohn Rd., Suite 1 Toronto, Ontario Canada M3B 2V9 1-866-656-2462 rel.