Quick Start Guide WS800 Wireless Microphone System Quick Start Guide
Setting Up ClearOne WS800 Wireless Systems for Optimal Performance Open the Cartons: Confirm everything on the packing slip is enclosed. 1. Set up the Docking Station: ClearOne transmitters are shipped with rechargeable batteries. Plug in the charging dock, put the batteries in the transmitters, then place the transmitters in the dock while you set up the rest of the system. 2. Mount the Receivers in the Rack and connect them to power. Confirm the displays light up. 3. Antenna Design: A.
Using the ClearOne remote software: Editing Transmitter Parameters: The easiest and most intuitive way to set the parameters of ClearOne transmitters and receivers is with ClearOne Remote software. Load ClearOne Remote from the disk provided onto a computer running Windows XP or Windows 7 (32 or 64-bit) and connect to the receiver via USB or RS232. Then open ClearOne Remote and select ONLINE. Open The Channel Edit Window: 1. The [Click to Edit] function opens the edit window of the channel you wish to edit.
How to sync transmitters with the receiver: How to sync transmitters with the receiver: 1. Locate the IR (infrared) Sensor on the transmitter. IR IR IR IR IR IR ON/OFF USB USB ON / OFF 2. Power on the transmitter. 3. Hold transmitter about 6 inches from the corresponding receiver module with the IR sensor aimed at the receiver module. 4. Simultaneously press the two buttons on the bottom of the corresponding receiver module to start sending the IR signal.
Receiver: FRONT PANNEL: ClearOne receiver main-frames hold either four or eight, independent, 24-bit digital audio receiver modules. There is a front-panel mixed audio output for headphones or direct recording. Each module shares the mainframe’s two antennas for full-diversity. Up to eight receiver main-frames can be daisy-chained together into an antenna network that shares two antennas. This eliminates the need for external antenna distribution amps.
Receiver: BACK PANEL WS880: 7 1 Made In USA IN IN - 8 + G - 7 + G - 6 + G - 5 + - G 4 + G - 3 + G - 2 + G - 1 + G OUT OUT 50-60 Hz 100-240 VAC ANTENNA B 2 3 ETHERNET 4 RS232-GPIO 5 ANTENNA A MIC OUTPUTS 6 8 BACK PANEL WS840: 7 1 Made In USA IN IN - 4 + G - 3 + G - OUT ANTENNA B 2 2 + G - 1 + G OUT 50-60 Hz 100-240 VAC 3 ETHERNET 4 RS232-GPIO 5 MIC OUTPUTS 6 ANTENNA A 8 1.
Transmitters: HAND-HELD: 6 8 6 9 8 9 7 1 3 2 4 4 10 11 12 1. Heads: Five (5) microphone condenser elements are available. In general, condenser heads are more “transparent” and do not require the microphone to be held as close to the mouth. 2. Display: OLED display is used to program and display the current status of the transmitter functions. 3. Switch: User programmable to toggle on/off, on/mute/ or on/on. 4. Battery and Control Cover: Unscrew counter-clockwise and gently slide open. 5.
Transmitters: CONFERENCE TABLE-TOP: The ClearOne DS80-C Conference Table-top Mic combines the professional audio specs and security of a wired mic with wireless convenience. Available in omni or cardioid polar pick-up patterns with 265-bit FIPS 197 encryption. 1. Power LED: When the Table Mic is on, the LED signals: Red = audio mute Green = audio passes Blinking Red = battery low Blinking Green = sync successful. 2. Contacts: Contact points for the charging station. 3.
Transmitters: PODIUM GOOSENECK: The ClearOne Podium microphone combines the professional audio specs and security of a wired mic with wireless convenience. For use with battery power or permanently install the microphone using USB power. 1 2 3 1. ClearOne Capsules: Cardioid polar pattern. 2. Goosenecks: Two flexible sections to extend over a laptop or briefcase. Available in 12 and 18 inch lengths. 3. Radio-transparent ABS Top: Stylish design that hides and protects the antenna. 4.
