VIEW® Pro High-definition, IP, Compressed Audio/Video Encoder, and Decoder Quick-Start Guide
Table of Contents THE VIEW PRO ENCODER AND DECODER.....................................1 QUICK-START OVERVIEW.................................................................1 MOUNTING THE ENCODER AND DECODER...................................2 THE ENCODER/DECODER IN NETWORK .......................................7 CONNECTING THE ENCODER..........................................................7 CONNECTING THE DECODER..........................................................
QUICK-START GUIDE THE VIEW PRO ENCODER AND DECODER The VIEW Pro E120 encoder takes digital video and audio from source devices, such as receivers, cable boxes or DVRs, and makes the source available anywhere on the StreamNet IP network. The VIEW Pro D110 decoder takes the combined video and audio stream, decodes it, and then sends the video and audio to a display such as a HDTV or projector and sound system.
VIEW PRO ENCODER/DECODER MOUNTING THE ENCODER AND DECODER The VIEW Pro Encoder includes rack-mount ears that attach to the encoder to facilitate mounting in a standard rack The VIEW Pro Decoder includes surface-mount ears that attach to the decoder to facilitate mounting on top of a surface, under a surface, or on a wall. It also includes mounting clips for the power supply.
QUICK-START GUIDE The power supply for the decoder can also be mounted to a wall using the included mounting clips. An optional VESA Mount Bracket Kit (910-0002-006) is available for applications where an encoder/decoder must be located on a VESA mount. The VESA Mount Bracket Kit (910-0002-006) includes a Wall Bracket that the can VESA Bracket can attach to. NOTE: The VESA adapter does not attach the decoder to the back of a monitor, but allows the decoder to be attached to a separate VESA mount.
VIEW PRO ENCODER/DECODER VESA Bracket 4
QUICK-START GUIDE Wall Bracket (Mount to stud or other solid surface) Unit with VESA Bracket hangs on Wall Bracket 5
VIEW PRO ENCODER/DECODER When the VIEW Pro cables cannot be concealed, cables can be surface mounted using the optional 910-0002-003 VIEW Pro Cable Raceway Kit. This raceway, in 12-inch joinable lengths, can be mounted to the wall to secure and cover the cables to the VIEW Pro devices. Use included wire ties to secure the cables to the wall bracket. Mount the wall brackets to a solid surface. (Wall screws not included) Make 11 inch spacing between top and bottom wall bracket mounting holes.
QUICK-START GUIDE THE ENCODER/DECODER IN NETWORK The VIEW Pro encoder receives input from an AV source device such as BluRay Player, DVD Player, etc. and distributes it over a StreamNet TCP/ IP network using a standard 100 Mbit or Gbit Ethernet connection. The decoders, as counterparts, are installed at the locations of the target video displays. They operate together: the encoders providing the IP data for the decoders to deliver to the displays.
VIEW PRO ENCODER/DECODER Left/Right Balanced Audio Intputs 6 GPIO Ports for Control 3 Inputs and 3 Outputs COM2 Port for Source or 3rd-Party Device Control 2 HDMI Audio/Video Port COM1 Port for Source or 3rd-Party Device Control Power On/Off 3.5mm IR Input 3.5mm IR for IR Learning Output for Source or 3rd-Party Control 19 VDC 2 x USB Network Port2 3.0 Ports (Currently Not Used) Input from for USB Power Adapter Audio/Video Devices Network Port1 3.5mm 3.
QUICK-START GUIDE CONFIGURING THE ENCODER/DECODER The VIEW Pro Encoder/Decoder is configured for use in the commercial or residential network using the StreamNet Dealer Setup program. StreamNet Dealer Setup is a PC-based program that allows you to configure devices so that they can communicate across a StreamNet network.
VIEW PRO ENCODER/DECODER VIEW PRO ACCESSORY KITS The following accessory kits are available to meet the mounting and control needs of your VIEW Pro Encoders and Decoders: Part Number Kit Name Description 910-0002-001 VIEW Pro Rack Mount Rack Mount Kit for VIEW Pro Encoder E120, Decoder D110 (Included with Encoder) • 2X - Rack Ear, Extended length • 6X - Screw, M3 x 6mm, Pan-head, Phillips, Thread Locking, Black VIEW Pro Wall Mount Wall Mount Kit for VIEW Pro Encoder E120, Decoder D110 (Included
QUICK-START GUIDE Part Number Kit Name Description 910-0002-004 VIEW Pro IR Receiver IR Receiver cable for VIEW Pro Encoder E120, Decoder D110 (Optional) • VIEW Pro IR Receiver & Emitter IR Receiver Cable, IR Emitter Cable Kit for VIEW Pro Encoder E120, Decoder D110 (Optional) • 1X - IR Receiver with 6 ft. cable, 3.5 mm plug • 1X - IR Emitter with 6 ft. cable, 3.5 mm plug 910-0002-005 910-0002-006 1X - IR Receiver Assembly with 6 ft.
VIEW PRO ENCODER/DECODER PART NUMBERS 910-0000-001 910-0001-001 VIEW Pro Encoder E120 VIEW Pro Decoder D110 CLEARONE CONTACTS HEADQUARTERS: Salt Lake City, UT USA 5225 Wiley Post Way Suite 500 Salt Lake City, UT 84116 Sales: 800.705.2103 Toll Free: 800.945.7730 Fax: 801.303.5711 e-mail: sales@clearone.com TechSales Tel: 800.705.2103 e-mail: techsales@clearone.com Technical Support Tel: 800.283.5936 e-mail: tech.support@clearone.com EMEA: Tel: +44 (0) 1189.036.053 e-mail: global@clearone.
