Beamforming Microphone Array Group Microphone for Professional Conferencing Quick-Start Guide
Table of Contents THE BEAMFORMING MICROPHONE ARRAY...................................1 QUICK-START OVERVIEW.................................................................2 Quick-Start Procedures.......................................................................2 UPDATING THE CONVERGE PRO FIRMWARE................................3 Upgrading from CONVERGE Pro 3.X firmware. ..................................4 Upgrading from CONVERGE Pro 2.X firmware. ..................................
QUICK-START GUIDE THE BEAMFORMING MICROPHONE ARRAY The Beamforming Microphone Array is 24-microphone device with beamforming and adaptive steering technology designed specifically for the with CONVERGE® Pro products: 880, 840T, 880T, 880TA. The Beamforming Microphone Array connects with the CONVERGE Pro through an Expansion Bus (E-bus) port: 3 arrays per supported CONVERGE Pro and up to 16 Beamforming Microphone Arrays can be daisy-chained in the site.
BEAMFORMING MICROPHONE ARRAY QUICK-START OVERVIEW Installing and using the Beamforming Microphone Array in your CONVERGE Pro site is subject to the following rules: 1. The Beamforming Microphone Array can only be used with CONVERGE Pro systems operating at version 4.X or greater, and requires that the firmware on the CONVERGE Pro and the Beamforming Microphone Array both be updated. 2. You must have a CONVERGE Pro 840T, 880, 880T and/or 880TA in the site.
QUICK-START GUIDE 3. Update the Beamforming Microphone Array firmware using CONVERGE Console. (The Beamforming Microphone Array firmware can not be upgraded directly without an updated CONVERGE Pro.) 4. Using the Beamforming Microphone Array 5. Mounting the Beamforming Microphone Array UPDATING THE CONVERGE PRO FIRMWARE The 4.X versions of CONVERGE Console offer significant upgrades from previous versions. Beamforming Microphone Arrays are not recognized by CONVERGE Pro units running older versions.
BEAMFORMING MICROPHONE ARRAY Upgrading from CONVERGE Pro 3.X firmware 1. Remove any 1.X, 2.X and 4.X units from the stack by disconnecting the expansion bus link cable from the 3.X units. 2. Re-connect to the 3.X stack with CONVERGE Console. 3. Download the 4.X firmware file to the stack of units. 4. The units will default and reboot after the download of 4.X firmware. 5. Units are fully upgraded. 6. Verify units have been upgraded by checking the firmware version on the front panel.
QUICK-START GUIDE 4. The units will default and reboot after the download of 4.X firmware. The 2.X to 4.X upgrade requires the firmware to be loaded twice to complete the version upgrade. 5. Units are fully upgraded. 6. Verify units have been upgraded by checking the firmware version on the front panel. Reconnect all E-bus cables, if needed, to complete the stack of units.
BEAMFORMING MICROPHONE ARRAY Upgrading from CONVERGE Pro 1.X firmware 1. Remove any 2.X, 3.X and 4.X units from the stack by disconnecting the expansion bus link cable from the 1.X units. 2. Re-connect to the 1.X stack with CONVERGE Console. 3. Download the 4.X firmware file to the stack of units. 4. The units will default and reboot after the download of 4.X firmware. The 1.X to 4.X upgrade requires the firmware to be loaded twice to complete the version upgrade. 5.
QUICK-START GUIDE CONNECTING THE BEAMFORMING MICROPHONE ARRAY Connect the Beamforming Microphone Array units to the CONVERGE Pro via the E-bus connections using CAT5-24AWG solid conductor RJ45 cables. Power can be through a standard Power-over-Ethernet switch or through an external PoE power supply. NOTE: The PoE connection is only for power, not control. Power must be for individual units; no daisy-chain power is allowed. Firmware upgrades, etc. are performed via the E-bus connection.
BEAMFORMING MICROPHONE ARRAY UPDATING THE FIRMWARE OF THE BEAMFORMING MICROPHONE ARRAY NOTE: All CONVERGE Pro units in the site must be running firmware level 4.X to be compatible with the Beamforming Microphone Array. Before continuing, follow the appropriate procedure above to update the firmware on the CONVERGE Pro units. 1. Connect the E-bus cable between the CONVERGE Pro units and the Beamforming Microphone Arrays. 2. Connect the CONVERGE Pro units with CONVERGE Console. 3.
QUICK-START GUIDE USING THE BEAMFORMING MICROPHONE ARRAY The Beamforming Microphone Array must be added to the site using the CONVERGE Console 4.X software. This software also provides the capability of configuring the pickup pattern and other characteristics available in Configuration mode. Refer to the online help available with the CONVERGE Pro software. Volume & Mute These controls are available through the controller configured for your CONVERGE Pro site.
BEAMFORMING MICROPHONE ARRAY MOUNTING THE BEAMFORMING MICROPHONE ARRAY The array can be ceiling-mounted in either a suspended or solid ceiling, or on a wall-mount assembly with the PoE and E-bus wiring passing through the mounting assembly and plugging into the Beamforming Microphone Array unit. Tabletop use is also supported with PoE and E-bus cables attached under the unit.
QUICK-START GUIDE Part Numbers 910-001-003 Beamforming Microphone Array for CONVERGE Pro 910-001-004 PoE Power Supply and Cables Kit for Beamforming Microphone Array 910-001-005-12 Ceiling Mounting Kit with 12” Suspension Column for Beamforming Microphone Array 910-001-005-24 Ceiling Mounting Kit with 24” Suspension Column for Beamforming Microphone Array 910-001-006 Wall Mounting Kit for Beamforming Microphone Array 11
BEAMFORMING MICROPHONE ARRAY CLEARONE CONTACTS HEADQUARTERS: Salt Lake City, UT USA 5225 Wiley Post Way Suite 500 Salt Lake City, UT 84116 Sales: 800-705-2103 Toll Free: 800.945.7730 Fax: 801.977.0087 e-mail: sales@clearone.com TechSales Tel: 800.705.2103 e-mail: techsales@clearone.com Technical Support Tel: 800.283.5936 e-mail: tech.support@clearone.com EMEA: Tel: +44 (0) 1189 036 053 e-mail: global@clearone.com APAC: Tel: +852 3590 4526 e-mail: global@clearone.