BHA2GSA/BHA3GSA BOOST HEIGHT-ADJUSTABLE WORKSTATION Includes Add-Ons: A1 | A2 | A3 | A4 General Installation Guide
TABLE OF CONTENTS EDITION CODE BHA :: Workstation ..................................................................1 ADD-ONS A1 :: Casters ...............................................................................9 A2 :: Modesty Panel.............................................................. 13 A3 :: Slim Pedestal .................................................................17 A4 :: Cable Tray .....................................................................
WORKSTATION OVERVIEW BOOST Height-Adjustable Workstation All parts listed are for a single workstation; additional parts will be needed for additional workstations.
CODE QTY ###### 1 Surface 1 Center-Adjustable Beam 1 Feet (Set of 2) 2 23" Arm Bracket 2 Leg with Motor 1 Handset 1 Short & Long Extension Cord 1 Power Cable 8 Screw (A) 24 Screw (B) 3 Screw (C) 8 Screw (D) BHANBEAM* 1 BOOST Replacement Beam BHA19* 2 19" Arm Bracket TLEG. ADAPTGSA* 1 T-Leg Adapter (Set of 2) BASB72* 1 42" Support Bar BHA3GSA DESCRIPTION WORKSTATION PARTS LIST or BHA2GSA *If applicable.
WORKSTATION 1 | DETERMINE SURFACE SIZE FOR INSTALLATION Use the chart below to identify which arm brackets will be used with surface size, and if surface will need replacement beam (BHANBEAM). Note: Reference STEP 4 after completing STEP 2 and 3.
Attach legs with motor and arm brackets to the center beam using screws (A). Note: Replace the default arm brackets if workstation requires BHA19 or T-brackets. Surface width 36"-47" will need to replace the beam, without the control box, with BOOST replacement beam (BHANABEAM). BHA19 WORKSTATION 2 | ASSEMBLE WORKSTATION FRAME BHANABEAM 3 | PLACE FRAME ON THE SURFACE Loosen existing locking screws on adjustable beam to extend beam to fit table size.
WORKSTATION 4 | ADJUST FRAME ON SURFACE Note: Based on STEP 1 surface size chart, reference one of the following workstation diagrams to secure frame. (A) 24"D x 36"–47"W Surfaces without Side Dividers Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C). (B) 24"D x 36"–47"W Surfaces with Side Dividers If using side dividers, frame will include arm brackets BHA19.
Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C). WORKSTATION (C) 24"D x 48"W and Smaller Surfaces without Side Dividers (D) 24"D x 48"W and Smaller Surfaces with Side Dividers If using side dividers, frame will include arm brackets BHA19. Extend the frame equal to the surface width. Center arm brackets in reference to surface depth.
WORKSTATION (E) 24"D x 54"–72"W Surfaces without Dividers Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C). (F) 24"D x 54"–72"W Surfaces with Side Dividers If using side dividers, inset the frame 2” from each end. Center arm brackets to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C).
Extend the frame equal to the surface width. Center arm brackets to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C). END OF WORKSTATION SECTION (G) 30" Deep Surfaces 5 | SECURE POWER CORD & INSTALL FEET Secure power cord to the control box. Secure locking screws on the adjustable beam and install the feet using screws (D) for each leg. If workstation is complete, flip over. Reference handset guide for initialization and operation functions.
A1: CASTERS OVERVIEW BOOST Height-Adjustable Workstation All parts listed are for a set of 4 casters; additional parts will be needed for additional casters.
CODE QTY 1 DESCRIPTION CASTERS PARTS LIST Caster Kit (Set of 4) BHACAST 16 Screws 10
CASTERS 11 1 | REMOVE GLIDES FROM FEET Unscrew all four glides from feet and disregard.
The workstation’s feet have pre-drilled holes for the caster plate. Attach casters using self-tapping metal screws.
A1: MODESTY PANEL OVERVIEW BOOST Height-Adjustable Workstation All parts listed are for a single modesty panel; additional parts will be needed for additional modesty panels.
CODE QTY DESCRIPTION 1 Laminate Modesty Panel* 4 Machine Screws 2 L-Brackets 4 Wood Screws MODESTY PANEL PARTS LIST GLMP## BMPBFB *For Steel Modesty Panel: components may vary, but process is similar.
MODESTY PANEL 15 1 | SECURE BRACKETS TO MODESTY PANEL Connect the BMPBFB bracket to the modesty panel using screws. Secure tightly.
Attach modesty panel to surface using wood screws provided with brackets. Panel will be center aligned and flushed with back of surface.
A2: SLIM PEDESTAL OVERVIEW BOOST Height-Adjustable Workstation All parts listed are for a single slim pedestal; additional parts will be needed for additional slim pedestals.
CODE QTY DESCRIPTION 1 Large Mounting Bracket 1 Small Mounting Bracket 1 Slim Pedestal 8 Machine Screw 10 Wood Screw SLIM PEDESTAL PARTS LIST BFSLM.SM BFSLM BFSLM.
SLIM PEDESTAL 19 1 | SECURE BRACKETS TO SLIM PEDESTAL Align large mounting bracket to front of pedestal and align small mounting bracket to back. Secure both brackets using provided screws.
Secure pedestal to surface using wood screws. The pedestal brackets will connect on either side of the center beam.
A3: CABLE TRAY OVERVIEW BOOST Height-Adjustable Workstation All parts listed are for a single cable tray; additional parts will be needed for additional cable trays.
CODE QTY 1 BHCT 10 DESCRIPTION CABLE TRAY PARTS LIST Surface-Mount Cable Management Tray Wood Screws 22
CABLE TRAY 23 1 | EXTEND CABLE TRAY TO DESIRED LENGTH Extension range: 25"–45".
Attach cable tray using wood screws.
1-866-304-7197 | inspire@mycleardesign.com | mycleardesign.com © 2022 Clear Design | Version 22.1.
