Instruction Manual

17 Tempest®24 00 MasterBelt
The MasterBelt default is for Dynamic Slot Assignment. This means that when BeltSta ons log in to a MasterBelt, the
informa on about the BeltSta ons is displayed on the MasterBelt LCD screen in alpha-numeric order according to the
name of the BeltSta on. For example, “Dir” appears before “Light1,” which appears before “StgMgr,” but they can change
slots depending on which BeltSta ons are turned ON. If the default se ngs are used, nothing is necessary.
Adjus ng so that each BeltSta on always appears in the same posi on of the MasterBelt display is a two step process:
1. Advance to the MasterBelt’s “Slot Assignment” sec on of the “Tech Menu” and select
Sta c.
2. In each BeltSta on, advance to the “Base Slot” sec on of the “Tech Menu” and adjust each BeltSta on to a diff erent
slot (1 – 5). The BeltSta on designated to slot 1 will always appear on the far le of the MasterBelt display, with slot 2
appearing in the next posi on to the right, and so on.
In
Sta c Mode, if a BeltSta on is not turned ON, or is logged out due to being out of range, the MasterBelt LCD display
will not have a shadow box around the respec ve slot number.
A Mul ple MasterBelt system that uses iSelect Roaming must choose to use “Dynamic” slots to ensure that BeltSta ons can
move from MasterBelt to MasterBelt when roaming.
Addi onal Se ngs and Features
Below are addi onal MasterBelt and BeltSta on se ngs that can be set based on individual preferences. None of these
adjustments are required and some features are limited to either the MasterBelt or BeltSta on:
•
Select Base - BeltSta ons can be paired with up to 64 MasterBelts (or BaseSta ons); Press MENU, select “Select
Base” and choose the to enable that BeltSta on to access a respec ve MasterBelt or BaseSta on.
•
Lock Keys - to prevent inadvertent changes. Press MENU, select “Lock Keys” to access lock op ons. Default se ng
is unlocked.
•
Menu Lock - allows you to lock individual users out of their respec ve BeltSta on menu en rely. Access can only be
regained by entering a 3-digit security key code (which is ini ally set at the MasterBelt) on each BeltSta on. Default
key code se ng is 000 and menu lock is disabled.
» To set key code at MasterBelt: Press MENU, select Belt Se ngs>Tech Menu>Belt Key; use volume knob to
scroll and set a key code. Press ENT to save.
» To enable “Menu Lock” at BeltSta on - Press MENU, select Lock Keys>Menu Lock
•
Ba ery Alert - Enable or disable the audible “Ba ery Alert” tone in the headset; Press MENU, select “Ba ery” and
Enable or Disable. Default se ng is Enable.
•
LCD/LED - Dim the LCD and LEDs to be less conspicuous in a dark environment:
» To enable or disable “LCD Light”: Press MENU, select LCD/LED>LCD Light
» To adjust the LED brightness: Press MENU, select LCD/LED>Talk LEDs and select either
High/Med/Low/Off .
•
Talk Bu ons - Set the TALK bu ons to operate in Latch or Momentary mode or Disable them completely. Press MENU,
select Set Controls>Talk Bu ons>Talk # and select either Latch/Momentary/Disable. Default se ng is Latch.
•
Channel (CH) Select - determine which channels are accessible and audible per MasterBelt or BeltSta on. Unit must
be set to access at least one channel. Press MENU, select Set Controls>Ch Select and choose from the channel
con gura ons available. Default se ng is access to all channels.
•
Mic Gain - Refer to the sec on “Adjust Mic Gain” in this manual.
•
Sidetone - Refer to the sec on “Adjust Sidetone” in this manual.