Cut Sheet

Directions for use
Bionik is a highly effective Concentrated Cleaner for use on any surface
compatible with water. Bionik can be diluted with water at a ratio of 1:3 for
degreasing or up to 1:512 parts water for cleaning glass and polished surfaces.
Bionik may also be applied undiluted. However it may be necessary to pre-wet
surface to activate the chemistry and soil load.
Bionik may be used with potable or salt water and its cleaning ability is not
dependent upon the pH of the solution. Mix in any sprayer, dispense through a
spray foaming device or a variety of mechanical proportioning systems.
Apply solution, agitate with a brush, abrasive pad, hand cloth or water spray.
Added dwell time, heat or agitation can optimize results. Rinse with clean water
and dispose of wastewater in an approved manner.
Depending on the specific factors in the cleaning environment, you will find which
dilution best accommodates desired cleaning speed using the least amount of
Bionik Concentrate.
When diluting, it is recommended that concentrate be added to the pre-measured
water to minimize foaming of the solution. The dilutions below are general
recommendations for various cleaning situations.
Phase Cleaning: 10% - 25% in solution
Restoration cleaning, equipment rebuilding, bath or soak solutions, heavy
cleaning: Organic soils, engines, auto parts, dried oil/enamel/latex paints, food
syrups, insect smears, dried animal or vegetable fats, hardened resins, asphalt
and grass or plants stains, parts washers, etc.
We recommend our VS-21 and VS-54 Solvents for removing synthetic
substances and compounded lubricants, gear and rail grease, ink, adhesives,
etc.
VS-21 is water compatible/rinseable and may be mixed with Bionik for heavy
cleaning of synthetic soil loads in addition to stained concrete cleaning.
Cycle Cleaning: 1% - 10% in solution
General maintenance cleaning, multi-surface, spray and wipe, CIP: Work
counters, and tolls, food and beverage processing equipment, carpet and
upholstery, oily floors, utility equipment, walls, finished floors, vehicle washing,
general janitorial, pressure sprayers, stainless steel, laminated materials, food
prep surfaces, glass and polished surfaces, etc.
Glass and Polished Surfaces: 1% - 2% in solution
1/2 ounce - 2 ounces per gallon of water.
For exterior glass cleaning: apply at stronger dilution using a sprayer, foaming
gun, bucket/cloth solution, etc. followed by agitation and rinsing, squeegee dry if
necessary. For interior use spray on window or cloth and polish dry with a clean
cloth or squeegee.
Cleaning Systems
Auto-Scrubbers, Extractors, Pressure Washers, recycling wash systems, etc.
Begin with 1/2 ounce - 8 ounce in per gallon of water in baths, supply tanks,
eduction lines, etc. Increase percentage gradually if necessary. For some
applications including carpet spot pre-soak; mix and spray or foam up to 10% -
25% in solution. Use 1/2 ounce per gallon of water to aid in dissolving cationic
detergents, organic fertilizers, treatment solutions, etc.
Note: Bionik Concentrate may tarnish some soft aluminum surfaces if not
adequately diluted and rinsed with water. Test first prior to use. Contact CleanVia
or your representative for additional product specific application data sheets.
Application Data
Applications
Marine
Vessel cleaning
Bilge pump systems
Food preparation
Oil Dispersion
Computer/Electronics
Finished component prep
Circuit board production
Polishing slurry
Ultrasonic cleaning
Power and Utility
Contact and wire cleaning
Non-conductive equipment
Oil and water separators
Manufacturing
Cutting and stamping lubrication
Maintenance and rebuild
Food processing
Fruit, vegetable and meat washing
Hospitality
Room service
Restroom maintenance
Food preparation
Construction
Equipment and tools
Dust suppressant
Hand washing
Form release agent
Mass transit
Vehicle wash
Engine cleaning
Graffiti prevention
Restoration
Smoke and water damage
Concrete cleaning
Upholstery
Veterinary
Animal cleaning
Facility maintenance
Bionik
Plant Based
Cleaner Concentrate
Non-Toxic │ Readily Biodegradable