Product Manual

ManualsBrandsCleanMaster ManualsAutomotive200 30-Gallon Solvent Parts Washer with Soak Tank

7578 Page 1 11-01-12

ECN 3783

INDUSTRIAL - SOLVENT PARTS CLEANER

REMOTE RESERVOIR

CM216 and CM230

I. Introduction

A. Manufacturer’s Statement

This manual will provide you with important information about the Solvent Parts Cleaners and will

instruct you on how to use this equipment in a safe manner.

The information contained in this manual is necessary for the safe, proper setup and operation of

your Solvent Parts Cleaner.

Keep this manual, along with the Material Safety Data Sheets (MSDS) for the solvent in use, within

easy reach of the operator of this parts cleaner.

The equipment described in this manual is subject to change. The manufacturer reserves the right to

change equipment at any time as part of normal product improvement. Some improvements may

have been made after this manual was printed. For the latest information on your equipment, contact

the manufacturer.

B. General Information

CAUTION

READ AND UNDERSTAND ALL LABELS, MSDS, AND

THIS INSTRUCTION MANUAL BEFORE USE.

The Industrial Solvent Parts Cleaner is an economical, safe, and innovative system designed to clean

parts, using a mineral spirits based solvent. Solvents, when used to clean grease and oil, must be

disposed of properly. Consult your local environmental management agency for additional guidance

and other potentially hazardous materials compliance requirements.

Install your parts cleaner on a flat, level surface in an area provided with adequate ventilation. Avoid

repeated or prolonged breathing of vapors. Do

NOT

use compressed air to dry parts as this may

cause a high concentration of vapors in the immediate area. Local exhaust ventilation should be used

in areas of high vapor concentration. Provisions for determining and maintaining adequate ventilation

are the responsibility of the operator.

Make sure the parts cleaner is connected to a properly grounded power source. Check serial plate for

power requirements.

NOT

allow the parts cleaner to operate unattended.

OPERATION & INSTRUCTION MANUAL

Summary of content (8 pages)

PAGE 1
INDUSTRIAL - SOLVENT PARTS CLEANER OPERATION & INSTRUCTION MANUAL REMOTE RESERVOIR CM216 and CM230 I. Introduction A. Manufacturer’s Statement This manual will provide you with important information about the Solvent Parts Cleaners and will instruct you on how to use this equipment in a safe manner. The information contained in this manual is necessary for the safe, proper setup and operation of your Solvent Parts Cleaner.
PAGE 2
II. Safety Instructions and Information Complete safety in use is dependent upon proper use and handling of the parts cleaner in your workplace. It is important that you follow the instructions provided in this manual. If you fail to read, understand, and follow all of the procedures in this manual, you may cause or suffer personal injury. DO NOT OPERATE ELECTRICAL EQUIPMENT INSIDE OF PARTS CLEANER.
PAGE 3
A. Important Safety Instructions 1. Read all instructions. 2. Care must be taken as burns can occur from touching hot parts. 3. Do not operate equipment with a damaged cord or if the equipment has been dropped or damaged – until it has been examined by a qualified service person. 4. If an extension cord is necessary, a cord with a current rating equal to or more than that of the equipment should be used. Cords rated for less current than the equipment may overheat.
PAGE 4
B. Service Call your representative should your parts cleaner need service and always unplug unit when servicing. Inspect and keep in good working order the power cord and all electrical components. If components show signs of damage or wear replace immediately. All work should be done by a trained technician. Do NOT replace pump before unplugging unit and letting it completely cool down. Do NOT replace fusible link with any other device to hold lid up.
PAGE 5
4. INGESTION (Swallowing): Uncontaminated cleaning solvent: and seek medical attention. DO NOT induce vomiting. Drink 4 to 8 ounces of water E. Environmental 1. Avoid spilling solvent. Spilled solvent can create slippery conditions, clean it up immediately. Close off area to traffic. Wear appropriate personal protective equipment to prevent eye and skin contact. Consult the Material Safety Data Sheet for instructions on clean up and disposal. 2. Contain leaks promptly.
PAGE 6
IV.
PAGE 7
ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 QTY 1 1 1 1 1 1 1 1 1 1 1 1 1 OPTION CM216 54105 53673 8136 8135 54268 6024 8169 53665 7317 8025 57041 8022 01122 7197 (16 GAL) PARTS LIST CM230 54098 53673 8136 8135 54268 6024 8169 53665 7317 8025 57041 8022 01122 7322 (30 GAL) DESCRIPTION PUMP ASSEMBLY 115V CONTROL BOX ASSEMBLY METAL GRATE STRAINER DOOR CLOSURE ASSEMBLY FLEXIBLE HOSE BRUSH, FLO THRU BRACKET, CTRL BOX PUMP, 115V 50/60HZ 205GPH PLUG, 15A POWER CORD RECEPTACLE 115V SWITCH, ROCKER DRUM, METAL V.
PAGE 8
Warranty and Limitation of Remedies and Disclaimer LIMITED WARRANTY AND LIMITATION OF REMEDIES AND DISCLAIMER. (1)Fountain Industries “Fountain” warrants the Equipment to be free from defects in material and manufacture and to conform to specifications for the Equipment at the time of shipment. This warranty is applicable only if the Equipment is installed, operated and maintained in accordance with factory recommendations and procedures.