User Manual

D2-007
User Manual
Ŷ
Ŷ
CleanDays Robotstofzuiger
Picture for reference only
ENEN
The content of user manual has been checked carefully.
Please contact us as soon as possible if there are any
printing errors or misunderstanding.
EN
EN
1.1 General Principles of Safety
1. Safety Precautions
Contents
1. S
afety Precautions
........................................................................
2
2. P
roduct Composition
......................................................................
5
3.
Product Use .................................................................................
9
4
.
Charging Operation
.............................................................................
13
5. P
roduct Maintenance
....................................................................
14
6.
Product Parameter
........................................................................
15
7.
Mop Assembly and Use Instructions...........................................................
16
Not to be used by children under the age of 8. People with physical or sensory
impairments, and some adults with developmental disabilities, along with people who
have no relevant experience may use this product under proper supervision and guidance
of those who understand the inherent risks
Warning: Do not touch the electronic components, batteries or charging stands of the robot.
Users are not allowed to maintain the internal components of the product.
Production maintenance needs authorized maintenance personnel to operate. Please make sure
that the rated power supply voltage of the charging stand meets the standard plug voltage.
1.2 Safety Instructions
Before operating the robot, please read all the safety precautions and operation
instructions.
Please pay attention to all warnings on the battery, power adapter, robot and user
instructions.
Please follow all operating and operation instructions.
The harm caused by wrong operation and the degree of damage are
described as follows.
8. Remote Instruction
......................................................................................
17
9.
WiFi Connection
............................................................................................
19
1.5 About Batteries
EN EN
Please remove all vulnerable
items before use.
Do not hold the front shell
to lift the vacuum cleaner.
Please use both hands to
hold the machine body to
lift the vacuum cleaner.
It is forbidden to use non-original
adapter and charging stand to charge
the machine, so as to avoid damage to
the machine.
1.4 About the Safety of Children
*Children are not allowed to use this product alone.
*Children are not allowed to play with the packaging bag of the product, otherwise
it may cause suffocation.
1. This product is only suitable for the original battery provided by
the manufacturer;
2. The battery must be taken out when the product is discarded;
3. If you need to replace the host battery, please contact our after-sales
service department. If you replace the battery with the wrong model, it
may lead to safety accidents;
4. In case of battery leakage, if the liquid sticks to the skin or clothes, wipe
it with dry cloth immediately. The discarded batteries shall be sent to the
recycling station or designated maintenance point, and shall not be discarded.
1.3 Product Safety Issues
Warning
This product is limited to the original battery charging stand
and adapter, otherwise it may cause product damage, electric
shock or fire caused by high voltage. Before use, please place
the rechargeable seat on the wall, and do not pl
ace any articles
within 2 meters in front and 1 meter in left and right.
Please do not use this product if the main engine and accessories
are damaged. Contact our after-sales service department. No one
is allowed to dismantle, repair or modify the product except the
maintenance technicians designated or authorized by the company.
Do not touch the power plug or product when the hand is wet,
otherwise electric shock may be caused.
Do not use the product in no protective fence situation , in order to
avoid accidental falling of vacuum cleaner and then person injury.
Do not use the power cord to drag or move the product. Do not over
twist, bend or place heavy objects on the power cord.
Do not let the product close to the fire source or the inflammable,
explosive and corrosive materials.
Keep away from direct heat, and any corrosive or explosive materials
Indoor use only Do not sue for spilled
liquids
Before use make use
extra cording is contained
and kept clear of vacuum
operation to avoid any
interference
Warning
5
EN
EN
2.1 Package List
2. Product Composition
Warm Reminder
1. Battery has bult-in the machine
2.1 Main Engine Diagram
Fixed point cleaning
Face plate
Auto recharge
Infrared Front Bumper
Start & Pause Button
Middle Cover
2. Start & Pause Button (start or pause)
. WiFi indicator light (connected to high
c
onfiguration version of mobile app)
Anti-Drop Sensor
Charging Electrode Piece
Side Brush
Universal Wheel
Side Brush
Battery Cover
Dustbin Vacuum Sniff
Right Wheel Drive
Dust Screen
Fine Filter
Efficient Filtration of HEPA
Left Wheel Drive
1
2. Filter has been installed on dust box
Serial Number Describe Quantity
1 Host (including battery) 1
2 Recharge Stand 1
3
Remote （Not Incuded battery）
1
4 The Power Adapter 1
5
1
6 Operation Instructions 1
7 Side Brush 2
8 High Efficiency Filter Screen 1
A Set of Mops for the Whole Machine
Anti-Drop Sensor
Anti-Drop Sensor
Dust box cover
ENEN
2.2 Host Diagram
Middle Cover
Dust Box
DC Power Jack
2.3 Diagram of Charging Stand
Charging Indicator
Power Adapter
Charging Electrode
Piece
Charging Electrode
Piece
Power Interface
2.4
Dust Bos Installation
Take out: hold the handle by hand and pull it out.Put in: Put the dust box back and
make sure it was flat
Cover Handle for the Dust Box
2.5 Cleaning and Brushes
Use the cleaning brush to clean the Debris on the side brushes. If there is more hair
on the side brush, you can use scissors to carefully cut the hair, and then clean it.
1. Installation Steps: Brush align the hole position, and hard press it down till hear the “snap”
sound, indicating that the side brush is installed .
2. Uninstallation Steps: Grasp the brush at any both ends of the brushes and pull it out with
the slight force.
Warm Tips:
Before using the device, please to check if the side Brushes has been installed, otherwise
it can not work.
Note:
To keep vacuum the most efficient, clean dust box filter after each use, filter
buildup will affect vacuum performance.
Contained charging cord
CH
EN
3. Use of Products
*Note: Before
,
remove the protective
bolt and tidy up the small objects or obstacles
in the room, especially the wires and other
entanglements which need to be cleaned.
3.1 Application Scope of the Product
Scope of
Application
The product is suitable for the following floors
wood
Tile
Scope of Inapplicability
*It is not suitable for use in extremely hot (+ 60 ℃)
or extremelycold (- 5 ℃) environment.
*This product is only suitable for indoor.
*It can not be used in the places without protective fence
to avoid personal injury caused by accidental fall of the
product.
*Do not use in humid or flammable, explosive and
corrosive environment.
*Do not allow the product to absorb cigarette butts or
matches that have not been extinguished.
*It can’t be used to absorb toner and color pan used in
laser printer and copier. These substances can cause fire.
*Do not use to absorb sharp objects, such as glass, nails,
etc., to avoid product damage.
3.2 Machine Working
3.2.1. On /Off
3.2.2. Standby Mode
If the machine is not operated, it will automatically shut down after 5 minutes
Press the button, the buzzer will alarm once and the machine will
enter the automatic cleaning mode.
Press the button, the buzzer will alarm once and the machine will
enter the automatic fixed-point cleaning mode.
Press the button, the buzzer will alarm once and the machine will
enter the automatic recharge mode.
Press the button for 3 seconds, the buzzer will alarm twice and the
machine will shut down.
6. Plug in the charger, the buzzer will alarm once and the light flashes, the
machine will enter the direct charging mode.
the Protective
the Protective
EN
When the machine is in standby mode, There are 6 different operation to next
step:
When the machine is in the “off”mode, press and hold “auto” button 3seconds.
The buzzer alarms one time, the three LEDs flash at the same time, and it
enters standby mode after 3seconds, LEDs stop flash and keep on.
*Do not use for carpet with thickness greater than 12mm, in order to avoid
machine jamming.
When the machine is ,
Press the Auto button on the machine, A button on the remote or
on the app
EN
3.2.3. Automatic Cleaning
When the machine is in automatic cleaning , the automatic cleaning is on. Th
. The machine according to the internal cleaning path,
and it avoids obstacles and steps.
Press the automatic or fixed-point button on the machine, the buzzer will alarm once，
and
the machine will enter the standby mode.
If the battery power is low, the buzzer alarms 3 times，then the machine will enter
the automatic
recharge mode.
the trouble, alarms
If the charger is inserted, the buzzer will alarm once and the machine will enter
the charging mode.
3.2.4. Fixed Point Cleaning Mode
When the machine is in the fixed-point cleaning mode, the fixed-point LED light is on,
and it
be recharged after three minutes leaning , which is suitable for cleaning
small-scale areas.
Press the automatic or fixed-point button on the machine, the buzzer will alarm once, and
the machine will enter into the standby mode.
3.2.5. Automatic Recharge
When the machine is in charging
, the LED light of automatic cleaning mode flashes,
indicating that it is charging, and the light
on when the machine is
fully charged.
3.2.6.
Troubleshooting
EN
Automatically go back charging stand to recharge when power is lower than 20 percent
No. Fa Mode Prompt
1
Left
LED flashes 1 once, and
buzzer alarms once.
Check whether the sensor lens on the left side
of the
machine is dusty and clean it.
2
Front
LED flashes , and
buzzer alarms once.
Check whether the sensor lens in front of the
machine is dusty and clean it.
3
Right
LED flashes 3 times, and
buzzer alarms once.
Check whether the sensor lens on the right
side of the
machine is dusty and clean it.
4
Right Collision
LED flashes 4 times, and
buzzer alarms once.
Check the right er housing
is jamming
5
LED flashes 5 times, and
buzzer alarms once.
er
6
Over Current
LED flashes 6 times, and
buzzer alarms once.
Check whether the left wheel is wrapped or
stuck.
7
LED flashes 7 times, and
buzzer alarms once.
Check whether the right wheel is wrapped or
stuck.
8 Abnormal Left wheel
LED flashes 8 times, and
buzzer alarms once.
Check whether the left wheel is wrapped or
stuck.
9
Abnormal right wheel
LED flashes 9 times, and
buzzer alarms once.
Check whether the right wheel is wrapped or
stuck.
10
Motor
LED flashes 10 times, and
buzzer alarms once.
Check whether there are foreign objects inside
the fan.
11
Side Brushes F
LED flashes 11 times, and
buzzer alarms once.
Check whether the left and right brus hes are
wrapped.
12
The machine
LED flashes 13 times, and
buzzer alarms once.
oreign objects
In the trouble situation, machine will stop working, Auto Cleaning light, Fixed Port Cleaning
light will on simultaneously, and buzzer will alarm, the machine will be off if have not any manual
operation. Different troubles as belows:
EN
5. Product Maintenance
4
. Charging Operation
4.1 Charging Stand Placement
4.2 Manual Charging
EN
5.1 Cleaning Side Brushes
Clean the side brush when it becomes dirty, If it is damaged, it can be replaced.
 Cleaning Brush
Remove the side brush and wipe with a clean
cloth.
 Clean the Universal Wheel
Clean the universal wheel to reduce hair
5.2 Cleaning of Dust Box and Filter
Take out the dust box.
Open the dust box and clean up the debris
Remove the filter
wash the HEPA with water, and remove the dust with a slight
taps.
Wash the dust box under running water and dry the dust box and filter parts
For optimal operation, we strongly suggest the base is,
1. on stable footing up against the wall.
2. the path to the base must be clear of all objects as not
to infringe it's path.
3. place no furniture, or other objects one meter to both
the right and the left of the base.
Connect the power adapter directly to the machine and connect the other
side to the power supply.
1. When charging for the first time, please charge for 12 hours.
2. During daily use, please store the machine on the charging stand and ensure
that the charging stand is connected to the power supply.
3. If you do not use the machine for a long time, please fully charge the machine,
turn off the machine and store it in a ventilated and dry place.
entanglement.
EN
15 16
EN
5.3 Cleaning of Sensor and Charging Electrode
Gently wipe the sensor and electrode piece with soft cloth.
Charging docking electrode
Sensor
Sensor
Charging docking electrode
Sensor
Charging docking electrode
Charging docking electrode
*Reminder:
6. Specifications
Working Voltage 7.4V
Rated Power 25W
Rechargeable Battery Lithium Battery
Battery Capacity 4400mAh
Charging Time About 4~5 Hours
Working Hours 90 mins
Operating Temperature Range -10䉝~45䉝
Operating Humidity Range 90%RH
Capacity of Dust Collection Box 600ML
Dimensions (L x W x H) 320*320*78mm
Mop Instructions
Remove protective sticker to reveal the adhesive side of the
Velcro
the two the position show in figure
free from dust and water stain
in the
It can be reused after washing mop
A.
Note: Always wring out the mop slightly after wetting it with water,
then stick it on the back of the machine to avoid excessive water stains.
17
18
EN
EN
LED Indicator
Standby Button
Button
Automatic Cleaning
Button
Fixed Point
Cleaning Button
emote nstructions
Auto Charge Button
Start / Pause
Infrared Signal Emission Lamp
Battery Cover
Troubleshooting
The following are the causes of the faults.
Number Fault Phenomenon Cause of Failure Solution
1
The
indicator does
not on red.
No battery or reverse polarity
Reinstall or replace
the battery
2
Low remote control
sensitivity
Low battery Replace the battery
Something is blocking the
remote control signal
Confirm to use in
open space
3 Button Failure
Foreign matters or water in the
button
Remove foreign
things
Low battery
Replace the battery
Contact the
manufacturer
Component
Category
Harmful Substances
Pb
And its
compou
nds
Hydrargyru
m
(Hg)
And its
compounds
Cadmium
(Cd)
And its
compounds
Hexavalent
chromium
（
CrVI）
And its
compounds
Polybrominat
ed biphenyls
（
PBB）
Polybrominat
ed diphenyl
ether
（PBDE）
Plastic parts ż ż ż ż ż ż
Hardware
（4）
X ż ż ż ż ż
Host Circuit
Modular
X ż ż ż ż ż
Battery ż ż ż ż ż ż
Plug power
line
(metal)
X ż ż ż ż ż
ż:It indicates that the content of the hazardous substance in all homogeneous materials of the part is
below the limit specified in the current effective version of GB / t26572.
X:It means that the content of the hazardous substance in at least one homogeneous material of the
component exceeds the limit requirements of the current effective version of GB / t26572, and there is
no mature alternative in the industry, which meets the environmental protection requirements of RoHS
directive of the European Union.
*Warm Reminder
*If the unit will not be used for an extended period of time, please remove and store the battery in a cool
location with low humidity
*In case of battery leakage, remove batteries, wipe the unit's battery compartment, and wash your hands.
*Do not allow water to enter the remote control. Do not use it in humid environment for a long time.
emote nstructions
Right Button
Forward Button
Backward Buton
Edge wall cleaning Button
AAA battery
20
EN
Sweeping robot
WiFi connection is in progress.
When the mobile phone displays add ed
successfully, click “ ” to enter the operation
interface.
When WiFi connection is successful, click the
modify icon on the right side of to change the
name.
Sweeping robot
The Schedule function is similar to the alarm
clock on the phone. After setting the cleaning
time, the machine will automatically enter the
automatic cleaning mode at the setting time as
long as the robot is in standby or charging on
the recharging stand.
1
2
3
4
A. Click “Settings” to enter the timing interface
(as shown in Figure 1.2).
B. Click the time you want to set, such as 15:47,
which can be repeated one or more times. Select the
working mode of appointment and save it (as shown
in Figure 3).
C. Click saving button in the upper right corner
(as shown in Figure 3).
D. If you need to cancel the setting time, click the
switch on the right. If it disappears, the appointment
of the day will be canceled.
E. When the machine reaches the setting time, it will
run automatically.
19
EN
WiFi
Smart Apple and
Register account and log in
Enter the interface
registrieren
China+86
Telefonnummer/Email
VĞƌŝĮnjŝĞƌƵŶŐƐcode abrufen
the + in the upper right corner.
Then
select
Tick "Confirm indicator rapidly blink" then click
Next icon
1). Cleaning switch( start /standby)
2). Standby
3). Smart( Auto Cleaning Mode)
4). Wall Follow( Edge Cleaning Mode)
5). Spiral(Fixed point Cleaning Mode)
6). Charging Base( Auto back to charge)
7). Manual (Start/ Pause or Direction)
8). Settings(Seek robot vacuum/ Timer)
5. Select the 2.4GHZ WIFI Network and enter
password, then Click Next icon
6.
Robot Vaccum (WiFi)
7. Schedule Function