Owners manual

Page 2
Brake and Clutch Pedal Arm Installation
Step 1: Remove any existing brake and (if applicable) clutch
pedals, along with the pedal axle or support pin that they
are hanging from. Remove any existing nylon flanged
bearings from the pedal hanger bracket.
Remove the clevis from your existing master cylinder
pushrod.
Step 2: Remove the cotter pin, clevis pin and clevis from the new
brake arm.
Step 3: Install the new clevis onto your existing master cylinder
pushrod.
Step 4: Insert the new nylon flanged bearings into the pedal
hanger bracket.
Step 5: Insert a 1/2" sleeve bearing into each of the nylon flanged
bearings.
Step 6: If you have manual brakes, the clevis should be
connected to the upper hole in the brake arm. If you
have power brakes, the clevis should be connected to
the lower hole in the brake arm.
Align the holes in the clevis with the correct hole in the
brake arm. Install the clevis pin, 3/8" AN washer, and cotter
pin.
Step 7: Install a 7/16" black washer onto the 7/16"-14 x 5-1/2"
hex bolt. Position the brake arm inside the pedal hanger
bracket. Note, 1967-1972 Chevelle: Make sure the
Chevelle Spacer is in position on the left (driver's) side of
the brake arm. Install the bolt from the right (passenger's)
side, pushing it through the side of the pedal hanger
bracket and into the brake arm.
As you push the bolt through the opposite side of the
pedal hanger bracket, make sure the 1/2" sleeve bearing
and nylon flanged bearing don't get pushed out by the
bolt. If they do, push them back in once the bolt is fully
inserted in the pedal hanger.
Step 8, 1967-1972 Chevelle: Install the clutch arm onto the bolt.
1967-69 Camaro/Firebird, 1964-1966 Chevelle, 1968-74
Nova: Install the clutch bushing onto the bolt and slide it
up next to the pedal hanger, against the nylon flanged
bearing. Then, install a Teflon washer and the clutch arm
onto the bolt.
Step 9: Install a Teflon washer and a 7/16" black washer onto the
bolt, and install and tighten the 7/16"-14 lock nut onto
the bolt. If the clutch pedal feels stiff, back the nut off just
enough so that the clutch arm will swing freely.
Step 10: Adjust the height of the brake pedal as needed. Tighten
the jam nut on your master cylinder pushrod.
Step 11: Connect your original clutch pushrod to the clutch arm.
Step 12: Adjust your brake light switch.
For exploded and assembled views:
• 1967-72 Chevelle, see Fig. 4 and Fig. 5
• 1967-69 Camaro, 1964-66 Chevelle, 1968-74 Nova,
see Fig. 6 and Fig. 7
Fig. 2 Fig. 3
Fig. 5
Fig. 7
Fig. 4
Fig. 6
Muscle Car Pedals Installation Instructions for 1964-72 Chevelle, 1967-69 Camaro, and 1968-74 Nova
CINS0003 Rev. 06/19/2018
© 2018 Clayton Machine Works
Clutch Bushing
Clutch Arm
Clutch Arm
Teon
Washer
Teon Washers
1967-69 Camaro,
1964-66 Chevelle,
1968-74 Nova
1967-69 Camaro, 1964-66 Chevelle, 1968-74 Nova 1967-69 Camaro, 1964-66 Chevelle, 1968-74 Nova
1967-69 Camaro, 1964-66 Chevelle, 1968-74 Nova
1967-72 Chevelle
1967-72 Chevelle
Brake Arm
Brake Arm
Brake Arm