Manual

ManualsBrandsClay Paky ManualsProjectorsPOINT MH

S E

ENTERSELECT

Press UP/DOWN to

select tIL function.

Press ENTER to access

the function.

S E

ENTERSELECT

The display shows the

minimum position (LO)

for Tilt movement.

Press ENTER to confirm.

S E

ENTERSELECT

H I

Press UP-DOWN to

select the maximum

position (HI) for Tilt

movement.

Press ENTER to confirm.

S E

ENTERSELECT

Press UP-DOWN to

select a value between 0

(corresponding to 0°)

and 255 (corresponding

to 208°).

Press ENTER to confirm.

The display shows: LO.

S E

ENTERSELECT

552

Press UP-DOWN to

select a value between 0

(corresponding to 0°)

and 255 (corresponding

to 208°).

Press ENTER to confirm.

The display shows: Hl.

Nota: To select value 0 quickly, press the UP button while

pressing DOWN. Vice versa, to select value 255 quickly,

press the DOWN button while pressing UP.

S E

ENTERSELECT

Press SELECT to return

to tlL.

S E

ENTERSELECT

Press UP/DOWN to

select SPd function.

Press ENTER to access

the function.

The display shows the

set speed.

S E

ENTERSELECT

S P1

Press UP/DOWN to

select the desired speed

from the settings:

SP1 (lowest speed)

SETTING DMX ADDRESS

S E

ENTERSELECT

Press SELECT.

The red led lights up.

S E

ENTERSELECT

Press UP/DOWN to

select the address.

Press ENTER to confirm.

Example: If the projectors use 4 channels, the first one

should have address 1; the second one address 5; the

third one address 9 and so on.

If the projectors use 6 channels, the first one should have

address 1; the second one address 7; the third one

address 13 and so on.

N.B.: For the last address, you have to consider the

channels used by the last projector so as not to exceed

the maximum value of valid addresses (507).

N.B.:

In the setting phase, if you press DOWN while

pressing UP the address decreases to the minimum

value (1). Vice versa, if you press UP while pressing

DOWN the address increases to the maximum value

(507).

Opt

OPTION MENU

(the options must be set on each individual projector)

S E

ENTERSELECT

Press SELECT twice.

The red led lights up and

the display shows:

OPt.

Press ENTER to confirm.

The display shows: Pln.

S E

ENTERSELECT

lPn

Press ENTER to access

Pln function.

S E

ENTERSELECT

With the UP/DOWN

button, select On to

activate, Off to disconnect.

Press ENTER to confirm.

The display shows:

Pln.

S E

ENTERSELECT

Press UP-DOWN to

select tln function.

Press ENTER to access

the function.

S E

ENTERSELECT

Using the UP/DOWN but-

ton, select On to activate,

Off to disconnect.

Press ENTER to confirm.

The display shows:

tln.

ROGRAMMING OPERATION WITH

CONTROL UNIT

tlL

FUNCTION

: vertical movement angle

SPd

FUNCTION

:Pan and Tilt movement speed

S E

ENTERSELECT

552

Press UP-DOWN to

select a value between 0

(corresponding to 0°)

and 255 (corresponding

to 360°).

Press ENTER to confirm.

The display shows: Hl.

Nota: To select value 0 quickly, press the UP button while

pressing DOWN. Vice versa, to select value 255 quickly,

press the DOWN button while pressing UP.

S E

ENTERSELECT

PAn

Press SELECT to return

to PAn.

Pln

FUNCTION

:Pan horizontal movement inversion

tln

FUNCTION

:Tilt vertical movement inversion

Hlr

FUNCTION

:Pan/Tilt high resolution

FuC

FUNCTION

: colour disc positioning only

on full colours

S E

ENTERSELECT

lrH

Press UP-DOWN to

select Hlr function.

Press ENTER to access

the function.

With this function, the projector uses 6 control channels

and gives greater resolution to Pan/Tilt movements.

S E

ENTERSELECT

Using the UP/DOWN but-

ton, select On to activate,

Off to disconnect.

Press ENTER to confirm.

The display shows:

Hlr.

S E

ENTERSELECT

uCF

Press UP-DOWN to

select

FuC function.

Press ENTER to access

the function.

S E

ENTERSELECT

Using the UP/DOWN but-

ton, select On to activate,

Off to disconnect.

Press ENTER to confirm.

The display shows:

FuC.

Press SELECT twice to return to rest mode.

SELECTING SLAVE MODE (SLA)

S E

ENTERSELECT

Press SELECT twice.

The red led lights up and

the display shows: OPt.

S E

ENTERSELECT

Press UP/DOWN to

select the automatic Aut

menu.

Press ENTER to confirm.

The display shows: EnA.

S E

ENTERSELECT

EnA

S E

ENTERSELECT

SLA

Press ENTER to access

EnA operating mode.

The display shows one

of the three following

modes:

SLA - SA - SAt.

Press UP-DOWN to

select SLAVE (SLA)

mode.

Press ENTER to confirm.

The display shows: EnA.

Press SELECT twice to return to rest mode and to

eventually program the functions in the

Opt options menu.

Press SELECT twice to return to rest mode.

DISPLAY AT MAXIMUM LUMINOSITY /

DISPLAY OFF

S E

ENTERSELECT

Press SELECT twice.

The red led lights up and

the display shows: OPt.

Press ENTER to confirm.

The display shows: Pln.

S E

ENTERSELECT

Ond

Press UP-DOWN to

select dOn function.

Press ENTER to access

the function.

S E

ENTERSELECT

Using the UP/DOWN but-

ton, select On to activate,

Off to disconnect.

Press ENTER to confirm.

The display shows:

dOn.

dOn

FUNCTION

: display at maximum luminosity

S E

ENTERSELECT

CCS

Press UP-DOWN to

select SCC function.

Press ENTER to access

the function.

S E

ENTERSELECT

Using the UP/DOWN but-

ton, select On to activate,

Off to disconnect.

Press ENTER to confirm.

The display shows:

SCC.

SCC

FUNCTION

: turns off the lamp during colour

change

SP2 - SP3 - SP4 - SP5 (highest speed).

Press ENTER to confirm. The display shows:

SPd.