ENGLISH A.LEDA B-EYE K10 EASY A.LEDA B-EYE K10 A.
SAFETY INFORMATION EN • Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare.
• Battery This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. LiFePO4 Pb • Disposing This product is supplied in compliance with European Directive 2012/19/EU - Waste Electrical and Electronic Equipment (WEEE). To preserve the environment please dispose/recycle this product at the end of its life according to the local regulation.
IT INFORMAZIONI DI SICUREZZA • Installazione Assicurarsi che tutte le parti per il fissaggio del proiettore siano in buona condizione. Assicurarsi della stabilità del punto di ancoraggio prima di posizionare il proiettore. La fune di sicurezza, debitamente agganciata all’apparecchio e fissata alla struttura di sostegno, deve essere installata in modo che, in caso di cedimento del sistema di supporto primario, si abbia la minor caduta possibile dell’apparecchio.
LiFePO4 Pb • Batteria Questo prodotto contiene una batteria ricaricabile piombo-acido o Litio Ferro Tetrafosfato. A tutela dell'ambiente si prega di smaltire la batteria a fine vita in conformità alla normativa vigente. Smaltimento Questo dispositivo è conforme alla Direttiva Europea 2012/19/UE - Rifiuti di apparecchiature elettriche ed elettroniche (RAEE). Nel rispetto dell'ambiente, smaltire/riciclare il prodotto al termine del suo ciclo di vita secondo le disposizioni di legge locali.
FR CONSIGNES DE SÉCURITÉ • Installation S’assurer que toutes les pièces pour la fixation du projecteur sont en bon état. S’assurer de la stabilité du point d’ancrage avant de positionner le projecteur. Le câble de sécurité, à fixer correctement à l’appareil et à la structure de support, doit être installé de façon à ce que, en cas de rupture du système de support principal, la chute de l’appareil soit la plus limitée possible.
LiFePO4 Pb • Batteria Ce produit contient une batterie rechargeable au plomb-acide ou tétraphosphate de fer au lithium. Une fois la batterie arrivée à la fin de sa durée de vie, procéder à son élimination conformément à la norme en vigueur de manière à éviter toute pollution. Élimination Ce dispositif est conforme à la Directive Européenne 2012/19/UE – Déchets d’équipements électriques et électroniques (DEEE).
DE IT INFORMATIONEN ZUR SICHERHEIT • Installation Sicherstellen, dass alle Teile für die Befestigung des Projektors in einwandfreiem Zustand sind. Vor der Installation des Projektors die Stabilität der Verankerungsstelle überprüfen. Das korrekt am Gerät eingehakte und an der Haltestruktur befestigte Sicherheitsseil muss so installiert werden, dass bei einem Nachgeben der Haupthalterung die Fallhöhe des Gerätes so gering wie möglich ist.
LiFePO4 Pb • Batterie Dieses Produkt enthält eine wiederaufladbare Blei-Säure-Batterie oder Lithium-Eisen-tetraphosphat. Zum Schutz der Umwelt bitten wir Sie, diese Batterie, nachdem sie verbraucht ist, gemäß den geltenden Vorschriften zu entsorgen. Entsorgung Diese Vorrichtung entspricht der Europäischen Richtlinie 2012/19/UE - Abfall von elektrischen und elektronischen Gerätschaften (RAEE).
ES INFORMACIONES DE SEGURIDAD • Instalación Asegúrese de que todos los elementos de fijación del proyector estén en buenas condiciones. Controle la estabilidad del punto de anclaje antes de instalar el proyector. La cuerda de seguridad, correctamente enganchada al aparato y fijada a la estructura de soporte, debe colocarse de modo que, si el soporte principal cede, el aparato sufra la menor caída posible. En caso de desgaste de la cuerda de seguridad, sustitúyala por el recambio original.
LiFePO4 Pb • Batería Este producto contiene una batería recargable plomo-ácido o de litio tetrafosfato Hierro. Para proteger el ambiente se ruega eliminar la batería conforme a la normativa vigente. Eliminación Este dispositivo es conforme a la Directiva Europea 2012/19/UE - Residuos de equipos eléctricos y electrónicos (RAEE).
UNPACKING AND PREPARATION 1 EASY B-EYE K10 A.LEDA DA B-EYE K10 A.LE B-EYE K20 A.LEDA ENGLISH ® INSTR PR IMIN EL INDEX n Safety informatio 2 on g and preparati Unpackin 3 n and start-up Installatio 4 Control panel 5 Menu setting 7 nce Maintena 15 17 17 18 C61419 C61420 Y AR Contents Page IST009/001 C61415 MANUAL UCTIO N n l informatio Technica problems solution of Cause and Channel product! a Clay Paky choosing lations on the rich Clay Congratu custom.
INSTALLATION AND START-UP 3 Installing the projector - Fig. 3 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
CONTROL PANEL 5 Mains Connecting to the mains supply - Fig. 5 6 DMX 512 5 PIN 5 4 3 1 2 SCREEN SIGNAL SIGNAL DMX 512 3 PIN SIGNAL 2 SCREEN 1 3 SIGNAL Connecting to the control signal line (DMX) - Fig. 6 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified.
8 28 28 Reversal of the display - Fig. 8 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512). The address can also be set with the projector switched off.
MENU SETTING XXX = default value Main Menu Level 1 Level 2 Level 3 Standard Shape DMX Art-net 0 - 255 Mode Basic Engine Source Universe DMX Address 1 - 512 Disabled RGB RGBW DMX Art-net 0 - 255 Mode Pixels Engine Source Universe 1 - 512 DMX Address SET UP Repeat on DMX Disabled Enabled on primary 0 - 255 Enablement Universe Control Protocol Ethernet Interface Custom IP Address Custom IP Mask Fixture ID A.
Main Menu Level 1 Level 2 On / Off Invert Tilt On / Off Swap Pan-Tilt On / Off Encoder Pan-Tilt On / Off Pan Home Def Pos Tilt Home Def Pos Silent Mode Fan Speed Mode OPTION Display Dimmer curve RGB Gamma Halogen Mode Default Preset User Preset 1 Setting User Preset 2 User Preset 3 A.LEDA B-EYE Standard Sequenced 0 degree 90 degrees 180 degrees 270 degrees 0% 12.5 % 25 % 50 % 75 % 87.
Main Menu Level 1 Level 2 Level 3 System Errors Fixture Hours LED Energy Tot System Version INFORMATION Board Diagnostic DMX Monitor Fans Monitor Sensor Status Network parameters MANUAL CONTROL TEST ADVANCED Read / Reset Read Read / Reset Read Read / Reset Fw.rev. Hw.rev. Fw.rev. Fw.rev. / Hw.rev. Fw.rev. / Hw.rev. Status / Err% Status / Err% Value / Percentage Speed (RPM) Speed (RPM) Speed (RPM) ON / OFF / n.a. ON / OFF / n.a. ON / OFF / n.a. ON / OFF / n.a.
NOTE: On grey the default options SET UP MENU For greater programming ease using the DMX control unit and Mediaserver Art-net, channel mapping is divided into BASIC ENGINE and PIXEL ENGINE (see details in Channel Function).
Set Up Ethernet Interface ETHERNET INTERFACE It lets you set the Ethernet settings to be attributed to the projector. Control Protocol Control Protocol It lets you select the Art-net “Control Protocol” to be assigned according to the control unit used. The following options are available: • Disabled • Art-net on IP 2.x.x.x • Art-net on IP 10.x.x.
Standard: Pan & Tilt are simultaneously reset. Sequenced: Tilt is reset first followed by Pan. to confirm the selection or LEFT to keep the current setting. 3) Press F D Pan Home Def Pos Lets you assign the Pan channel “home” position at the end of Reset, without a DMX input signal. , the current setting appears on the display.
Set Up Special Functions B C 2) Use the UP and DOWN keys to select one of the following settings: - Curve 1 - Curve 2 - Curve 3 - Curve 4 3) Press to confirm the selection or LEFT to keep current settings. F D RGB Gamma Lets you select three different RGBW gamma curves. - the current setting appears on the display. 1) Press 2) Use the UP and DOWN keys to select one of the following settings: - Gamma 1.0 - Gamma 1.5 - Gamma 2.0 to confirm the selection or LEFT to keep current settings.
Fixture Hours FIXTURE HOURS Used for displaying projector operating hours (total and partial). 1) Press - Hours total and partial appears on the display. Total counter Counts the number of projector working life hours (from manufacture to date). Partial counter Counts the number of partial projector working life hours since the last reset to date. 2) Press to reset partial projector working hours a confirmation message (Are you sure?) appears on the display.
Manual Control No Reset MANUAL CONTROL Yes RESET Used for resetting the projector. 1) Press to reset the projectors, a confirmation message (Are you sure ?) appears on the display. 2) Select YES to starting reset the fixture or NO to keep the current setting and return to the top menu level. F Channel CHANNEL Used for setting channel levels from the projector control panel. - the first channel appears on the display.
9 WARNING: no alcohol Light collimation system This product contains internal light collimation system. Avoid intense light from any angle. CAUTION: • Light collimation system This product contains internal light collimation system. Avoid intense light from any angle.
10 1 2 6 3 4 5 Battery removal - Fig. 10 This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. LiFePO4 Pb A.
MAINTENANCE 11 3 4 1 2 Opening the covers - Fig. 11 12 1 2 1 1 1 Removing/Assembling the lens unit - Fig. 12 A.
13 Replacing the line actuator - Fig. 13 CAUSE AND SOLUTION OF PROBLEMS THE PROJECTOR WILL NOT SWITCH ON PROBLEMS ELECTRONICS NON-OPERATIONAL DEFECTIVE PROJECTION POSSIBLE CAUSES CHECKS AND REMEDIES REDUCED LUMINOSITY No mains supply. LED exhausted or defective. Signal transmission cable faulty or disconnected. Incorrect addressing. Fault in the electronic circuits. Lenses or reflector broken Dust or grease deposited. A.LEDA B-EYE Check the power supply voltage. Call an authorised technician.
TECHNICAL INFORMATION 350 (13.78") Zoom OUT 310 (12.20") Zoom IN Power supplies available 100-240V 50/60Hz A.Leda B-EYE K10 233 (9.17") Zoom OUT 189 (7.44") Zoom IN Input power • K20 - 750VA • K10 - 450VA 248 (9.76") 360 (14.17") 423 (16.65") Total output B-EYE K10: 5500 lumens B-EYE K10 Easy: 4800 lumens B-EYE K20: 9800 lumens LED source Osram Ostar RGBW LED - 15W Average LED life: 50.000 h Motors 5 (k10), 7 (k20) stepper motors, operating with microsteps, totally microprocessor controlled. 494 (19.
CHANNEL FUNCTION A.
A.LEDA B-EYE K10 BASIC ENGINE PIXEL ENGINE STANDARD SHAPES CHANNEL CHANNEL CHANNEL MODE Pixel Engine need to be enabled through the FUNCTION channel (bit 103-105).
A.LEDA B-EYE K20 BASIC ENGINE PIXEL ENGINE STANDARD SHAPES CHANNEL CHANNEL CHANNEL MODE Pixel Engine need to be enabled through the FUNCTION channel (bit 103-105).
NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 128 bit - Tilt 128 bit ) all the others channels stay at 0 bit.
• STOP STROBE - FOREGROUND STROBE - BACKGROUND STROBE MACRO BIT EFFECT 252 - 255 239 - 251 226 - 238 213 - 225 208 - 212 207 OPEN RANDOM FAST STROBE RANDOM MEDIUM STROBE RANDOM SLOW STROBE OPEN FAST PULSATION (25 flash/sec) 108 104 - 107 103 SLOW PULSATION (0,5 flash/sec) OPEN FAST STROBE (25 flash/sec) 4 0-3 • TILT FINE • TILT BIT BIT 255 255 0 0 SLOW STROBE (1 flash/sec) CLOSED GOff Operation with option InvertTilt • DIMMER • DIMMER FINE BIT 255 0 EFFECT EFFECT BIT FULL LIGHT 255
• RESET BIT 255 • RED LED 1 to… GREEN LED 1 to… BLUE LED 1 to… WHITE LED 1 to… EFFECT COMPLETE RESET Complete reset is activated passing throug the unused range and staying 5 seconds in complete reset levels 128 127 BIT EFFECT 255 LED ON 0 LED OFF COMPLETE RESET PAN / TILT RESET Pan / Tilt reset is activated passing throug the unused range and staying 5 seconds in Pan / Tilt reset levels 77 76 PAN / TILT RESET ZOOM RESET Effects reset is activated passing throug the unused range and staying 5 se
SHAPE SPEED - SHAPE OFFSET - SHAPE FADE - BACKGROUND SELECT Shape Shape Selection Slot 0-7 8 9 10 11 12 13 1 2 3 4 5 6 Macro Name On K10 On K20 Macro OFF Pixel 1 Ring 1 Ring 2 Ring 3 Pixel 1+Ring 1 Pixel 1+Ring 2 Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Description Random colors *1 SHAPE SPEED SHAPE OFFSET SHAPE FADE N.a. N.a. N.a. N.a. N.a. N.a. N.a. Static effects. The ring or rings used by the macro are turned-on with the foreground colour.
Shape Shape Selection Slot Macro Name Bar 2 (Variable size) Random explosion On K10 On K20 Yes Yes N.a.
• SHAPE FADE • SHAPE TRANSITION BIT 246-255 245 243 244 18 17 16 0-15 BIT EFFECT Smooth, fading curve with automatic gamma * Smooth, fading curve gamma 2 Smooth, fading curve gamma 1,986 Smooth, fading curve gamma 1,993 Smooth, fading curve gamma 0,513 Smooth, fading curve gamma 0,506 Smooth, fading curve gamma 0,5 Snap EFFECT 255 4 sec 216 3 sec 171 2 sec 113 1 sec 73 0,5 sec 5 100 ms 0-4 No fade • BACKGROUND SELECT Aleda K10 - Background select • SHAPE RGBW SHAPE DIMMER BACKGROUND D
A.LEDA B-EYE K10 & K10 EASY LED reference number for pixel mapping TILT: channel 16 @ 200 bit 13 14 12 15 4 11 5 16 LED 3 6 1 10 17 2 7 18 9 19 8 A.LEDA B-EYE K20 LED reference number for pixel mapping TILT: channel 16 @ 200 bit 28 29 30 27 26 13 14 4 5 31 12 15 25 11 LED 3 24 32 16 6 1 33 10 17 2 23 7 9 22 8 19 20 37 21 A.
IST009/001 – EN - Rev.A 02/2015 CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.
