Instruction manual

ManualsBrandsClay Paky ManualsFlood LightA.LEDA B-EYE K10 EASY

A.LEDA B-EYE K10 EASY

A.LEDA B-EYE K10

A.LEDA B-EYE K20

C61415

C61419

61420

INSTRUCTION MANUAL

Congratulations on choosing a Clay Paky product!

We thank you for your custom.

Please note that this product, as all the others in the rich Clay

Paky range, has been designed and made with total quality to

ensure excellent performance and best meet your expectations

and requirements.

Carefully read this instruction manual in its entirety and keep it

safe for future reference. It is essential to know the information

and comply with the instructions given in this manual to ensure

the fitting is installed, used and serviced correctly and safely.

CLAY PAKY S.p.A. disclaims all liability for damage to the fitting

or to other property or persons deriving from installation, use and

maintenance that have not been carried out in conformity with this

instruction manual, which must always accompany the fitting.

CLAY PAKY S.p.A. reserves the right to modify the

characteristics stated in this instruction manual at any time and

without prior notice.

ENGLISH

INDEX

Page

Contents

Safety information

Unpacking and preparation

Installation and start-up

Control panel

Menu setting

Maintenance

Cause and solution of problems

Technical information

Channel functions

Summary of content (32 pages)

PAGE 1
ENGLISH A.LEDA B-EYE K10 EASY A.LEDA B-EYE K10 A.LEDA B-EYE K20 C61415 C61419 C61420 INSTRUCTION MANUAL INDEX Page Contents 2 Safety information 4 Unpacking and preparation 5 Installation and start-up 6 Control panel 8 Menu setting 18 Maintenance 19 Cause and solution of problems 20 Technical information 21 Channel functions Congratulations on choosing a Clay Paky product! We thank you for your custom.
PAGE 2
SAFETY INFORMATION • Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare.
PAGE 3
• Battery This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. LiFePO4 Pb • Disposing This product is supplied in compliance with European Directive 2012/19/EU - Waste Electrical and Electronic Equipment (WEEE). To preserve the environment please dispose/recycle this product at the end of its life according to the local regulation.
PAGE 4
UNPACKING AND PREPARATION 1 EASY B-EYE K10 A.LEDA DA B-EYE K10 A.LE B-EYE K20 A.LEDA ENGLISH ® INSTR PR IMIN EL INDEX n Safety informatio 2 on g and preparati Unpackin 3 n and start-up Installatio 4 Control panel 5 Menu setting 7 nce Maintena 15 17 17 18 C61419 C61420 Y AR Contents Page IST009/001 C61415 MANUAL UCTIO N n l informatio Technica problems solution of Cause and Channel product! a Clay Paky choosing lations on the rich Clay Congratu custom.
PAGE 5
INSTALLATION AND START-UP 3 Installing the projector - Fig. 3 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
PAGE 6
CONTROL PANEL 5 Mains Connecting to the mains supply - Fig. 5 6 DMX 512 5 PIN 5 4 3 1 2 SCREEN SIGNAL SIGNAL DMX 512 3 PIN SIGNAL 2 SCREEN 1 3 SIGNAL Connecting to the control signal line (DMX) - Fig. 6 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified.
PAGE 7
8 28 28 Reversal of the display - Fig. 8 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512). The address can also be set with the projector switched off.
PAGE 8
MENU SETTING XXX = default value Main Menu Level 1 Level 2 Source Universe DMX Address Mode SET UP Pixels Engine Source Universe DMX Address Repeat on DMX Control Protocol Fixture ID A.LEDA B-EYE 1 - 512 Disabled RGB RGBW DMX Art-net 0 - 255 1 - 512 Disabled Enabled on primary 0 - 255 Enablement Universe Ethernet Interface Choices / Values Standard Shape DMX Art-net 0 - 255 Mode Basic Engine Level 3 8 Disabled Art-net on IP 2.x.x.x Art-net on IP 10.x.x.
PAGE 9
Main Menu Level 1 Level 2 On / Off Invert Tilt On / Off Swap Pan-Tilt On / Off Encoder Pan-Tilt On / Off Pan Home Def Pos Tilt Home Def Pos Silent Mode Fan Speed Mode OPTION Display Dimmer curve RGB Gamma Halogen Mode Default Preset User Preset 1 Setting User Preset 2 User Preset 3 A.LEDA B-EYE Standard Sequenced 0 degree 90 degrees 180 degrees 270 degrees 0% 12.5 % 25 % 50 % 75 % 87.
PAGE 10
Main Menu Level 1 Level 2 Level 3 System Errors Fixture Hours LED Energy Tot System Version INFORMATION Board Diagnostic DMX Monitor Fans Monitor Sensor Status Network parameters MANUAL CONTROL TEST ADVANCED Read / Reset Read Read / Reset Read Read / Reset Fw.rev. Hw.rev. Fw.rev. Fw.rev. / Hw.rev. Fw.rev. / Hw.rev. Status / Err% Status / Err% Value / Percentage Speed (RPM) Speed (RPM) Speed (RPM) ON / OFF / n.a. ON / OFF / n.a. ON / OFF / n.a. ON / OFF / n.a.
PAGE 11
NOTE: On grey the default options SET UP MENU For greater programming ease using the DMX control unit and Mediaserver Art-net, channel mapping is divided into BASIC ENGINE and PIXEL ENGINE (see details in Channel Function).
PAGE 12
OPTIONS MENU Option Pan / Tilt Invert Pan PAN / TILT Invert pan Used for reversing Pan movement. - the current settings appear on the display (On or Off). 1) Press and DOWN keys to enable (On) or disable (Off) 2) Use the UP PAN inversion. to confirm the selection or LEFT to keep current settings. 3) Press On Off F B C F Invert Tilt D Invert tilt Used for reversing tilt movement. - the current settings appear on the display (On or Off).
PAGE 13
DISPLAY Used for automatically reduce brightness on the display after about 30 seconds in idle. - the current settings appear on the display (On or Off). 1) Press and DOWN keys to enable (On) or disable (Off) 2) Use the UP the decreasing of display brightness. to confirm the selection or LEFT to keep current settings.
PAGE 14
E D By pressing the RIGHT key and the LEFT key simultaneously once entered in the "main menu" it is possible to quickly (short cut) reset the default settings (DEFAULT PRESET). Used for restoring default values on all options menu items and relevant submenus. , a confirmation message (Are you sure?) appears on the display. 1) Press 2) Select YES to confirm the selction or NO to keep current setting.
PAGE 15
NETWORK PARAMS Allows the "Network" parameters of the projector to be displayed or: IP address: Internet Protocol address (two projectors must not have the same IP address) IP mask: 255.0.0.0 Mac address: Media Access Control: the projector’s Ethernet Address. Network params MANUAL CONTROL Manual Control RESET Used for resetting the projector. to reset the projectors, a confirmation message (Are you 1) Press sure ?) appears on the display.
PAGE 16
9 WARNING: no alcohol Light collimation system This product contains internal light collimation system. Avoid intense light from any angle. CAUTION: • Light collimation system This product contains internal light collimation system. Avoid intense light from any angle.
PAGE 17
10 1 2 6 3 4 5 Battery removal - Fig. 10 This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. LiFePO4 Pb A.
PAGE 18
MAINTENANCE 11 3 4 1 2 Opening the covers - Fig. 11 12 1 2 1 1 1 Removing/Assembling the lens unit - Fig. 12 A.
PAGE 19
13 Replacing the line actuator - Fig. 13 CAUSE AND SOLUTION OF PROBLEMS THE PROJECTOR WILL NOT SWITCH ON ELECTRONICS NON-OPERATIONAL PROBLEMS DEFECTIVE PROJECTION REDUCED LUMINOSITY POSSIBLE CAUSES No mains supply. LED exhausted or defective. Signal transmission cable faulty or disconnected. Incorrect addressing. Fault in the electronic circuits. Lenses or reflector broken Dust or grease deposited. A.LEDA B-EYE CHECKS AND REMEDIES Check the power supply voltage. Call an authorised technician.
PAGE 20
TECHNICAL INFORMATION 350 (13.78") Zoom OUT 310 (12.20") Zoom IN Power supplies available 100-240V 50/60Hz A.Leda B-EYE K10 233 (9.17") Zoom OUT 189 (7.44") Zoom IN Input power • K20 - 750VA • K10 - 450VA 248 (9.76") 360 (14.17") 423 (16.65") Total output B-EYE K10: 5500 lumens B-EYE K10 Easy: 4800 lumens B-EYE K20: 9800 lumens LED source Osram Ostar RGBW LED - 15W Average LED life: 50.000 h Motors 5 (k10), 7 (k20) stepper motors, operating with microsteps, totally microprocessor controlled. 494 (19.
PAGE 21
CHANNEL FUNCTION A.
PAGE 22
A.
PAGE 23
A.
PAGE 24
NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 128 bit - Tilt 128 bit ) all the others channels stay at 0 bit.
PAGE 25
• STOP STROBE - FOREGROUND STROBE - BACKGROUND STROBE MACRO BIT EFFECT 252 - 255 239 - 251 226 - 238 213 - 225 208 - 212 207 OPEN RANDOM FAST STROBE RANDOM MEDIUM STROBE RANDOM SLOW STROBE OPEN FAST PULSATION (25 flash/sec) 108 104 - 107 103 SLOW PULSATION (0,5 flash/sec) OPEN FAST STROBE (25 flash/sec) 4 0-3 • TILT FINE • TILT BIT BIT 255 255 0 0 SLOW STROBE (1 flash/sec) CLOSED GOff Operation with option InvertTilt • DIMMER • DIMMER FINE BIT 255 0 EFFECT EFFECT BIT FULL LIGHT 255
PAGE 26
• RESET 255 • RED LED 1 to… GREEN LED 1 to… BLUE LED 1 to… WHITE LED 1 to… EFFECT BIT COMPLETE RESET Complete reset is activated passing throug the unused range and staying 5 seconds in complete reset levels 128 127 BIT EFFECT 255 LED ON 0 LED OFF COMPLETE RESET PAN / TILT RESET Pan / Tilt reset is activated passing throug the unused range and staying 5 seconds in Pan / Tilt reset levels 77 76 PAN / TILT RESET ZOOM RESET Effects reset is activated passing throug the unused range and staying 5
PAGE 27
SHAPE SPEED - SHAPE OFFSET - SHAPE FADE - BACKGROUND SELECT Shape Shape Selection Slot 0-7 8 9 10 11 12 13 1 2 3 4 5 6 Macro Name On K10 On K20 Macro OFF Pixel 1 Ring 1 Ring 2 Ring 3 Pixel 1+Ring 1 Pixel 1+Ring 2 Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Description Random colors *1 SHAPE SPEED SHAPE OFFSET SHAPE FADE N.a. N.a. N.a. N.a. N.a. N.a. N.a. Static effects. The ring or rings used by the macro are turned-on with the foreground colour.
PAGE 28
Shape Shape Selection Slot Macro Name Bar 2 (Variable size) Random explosion On K10 On K20 Yes Yes N.a.
PAGE 29
• SHAPE FADE • SHAPE TRANSITION BIT 246-255 245 243 244 18 17 16 0-15 BIT EFFECT Smooth, fading curve with automatic gamma * Smooth, fading curve gamma 2 Smooth, fading curve gamma 1,986 Smooth, fading curve gamma 1,993 Smooth, fading curve gamma 0,513 Smooth, fading curve gamma 0,506 Smooth, fading curve gamma 0,5 Snap EFFECT 255 4 sec 216 3 sec 171 2 sec 113 1 sec 73 0,5 sec 5 100 ms 0-4 No fade • BACKGROUND SELECT Aleda K10 - Background select • SHAPE RGBW SHAPE DIMMER BACKGROUND D
PAGE 30
A.LEDA B-EYE K10 & K10 EASY LED reference number for pixel mapping TILT: channel 16 @ 200 bit 13 14 12 15 4 11 5 16 LED 3 6 1 10 17 2 7 18 9 19 8 A.LEDA B-EYE K20 LED reference number for pixel mapping TILT: channel 16 @ 200 bit 28 29 30 27 26 13 14 4 5 31 12 15 25 11 LED 3 24 32 16 6 1 33 10 17 2 23 7 9 22 8 19 20 37 21 A.
PAGE 31
PAGE 32
IST009/001 – EN - Rev.0 11/14 CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.