Owner`s manual

ManualsBrandsClasse Audio ManualsComputer equipmentDAC-1

These outputs allow you to easily connect the

SSP-75 to any power amplifier(s). We recommend

utilizing the Balanced outputs to eliminate ground

loops and induced hum and noise. However,

you may use any of these connections in any

combination that does not duplicate channel

assignments. For example, you may use the Front

Left and Right channel balanced XLR outputs to

connect the SSP-75 to the power amplifier(s) for

those speakers and the RCA connectors for other

channels which have no balanced inputs.

1.3.2.1 RECORD AND ZONE AUDIO OUTPUTS

a) VIDEO6 RECORD (Two Channel analog) These

two channels are stereo. These outputs only output

analog information from the VID1 through 5 analog

inputs. They will not output a signal if the audio

source is digital. They should be connected to the

analog INPUT of any Audio/ Video recorder you’re

using. b) ZONE (Two Channel analog) These two

channels are stereo. These outputs only output

analog information from the VID1 through 5

analog inputs and the AUDIO1 through 6 analog

inputs. They will not output a signal if the audio

source is digital.

PLEASE NOTE: Most DVD players have an analog

two channel ‘MIXED’ output in addition to the

Digital, and in addition to any 5.1 analog outputs.

When a 5.1 disc is being played the ‘Mixed’ analog

two channel output is essentially Dolby Pro Logic.

This material and can be utilized as stereo or further

decoded by a Dolby Pro Logic processor. We

recommend that if you wish to record a movie from

a DVD (for your own use) you utilize the ‘Mixed’

two channel output from the DVD Player by

connecting it to the SSP-75 at the same analog

input as the Digital input. For example, plug the

‘Mixed’ analog into VID3 if you are connecting the

Digital audio (5.1) feed into VID3. This signal will be

supplied always to the VIDEO6 RECORD output and

the audio only RECORD OUT. Either of the RECORD

outputs will always supply the analog signal (if any)

from the SOURCE being listened to in the MAIN

room. If you have selected the same SOURCE for

the ZONE output the two channel analog signal

will be sent there too.

1.3.2.3 RECORD OUT

a) (Two Channel analog) These two channels are

stereo, line level. These outputs only line level (fixed

level) output analog information from the VID1

through 5 analog inputs and the AUDIO1 through 6

analog inputs. They will not output a signal if the

audio source is digital. We recommend that if you

wish to record a CD (for your own use) you utilize

the two channel output from the CD Player by

connecting it to the SSP-75 at the same analog

input as the Digital input. For example, plug the

analog into AUDIO3 if you are connecting the

Digital audio feed into AUDIO3. (Also see the

Note below regarding the Digital Outputs).

1.3.2.4 DIGITAL OUTPUTS

a) COAX, Direct feed from the currently accessed

Digital input. Accepts standard S/PDIF digital signals

via 75 ohm coaxial cables with RCA-style connectors.

b) OPTICAL, Direct feed from the currently

accessed Digital input. Accepts a Toslink-style

optical connector for digital source components

with TOSlink digital input.

PLEASE NOTE: either of these outputs may be

utilized to tape the unprocessed digital output from

a DVD player or CD transport or CD Player with a

digital output. A Digital recorder is required, or

separate DAC is required to convert the digital

stream to analog. This feed could also be used with

a DAC which processes 24/96 or 24/192, with the

resulting analog output being connected to the

VID6 input. By Selecting the VID6 SOURCE, which is

the Tape Monitor input, you can listen to externally

processed material, utilizing the advanced switching

network of the SSP-75. Any Digital input (AES/EBU,

COAXIAL or TOSlink), when selected as the

SOURCE for Main room playback, will appear

at the COAXIAL and TOSlink Digital outputs.

1.3.2.5 S-VIDEO OUTPUTS

a) VID6 RECORD, Output to S-Video(Y/C) input

of a VCR or other A/V recorder (No OSD)

b) MONITOR OSD, with On Screen Display

c) MONITOR NO OSD, without On Screen Display

These S-Video outputs direct video signals

from various SOURCE components to selected

destinations. The MONITOR S-Video outputs

transfer a chosen SOURCE’s S-Video signal to any

monitor or TV set with an S-Video (Y/C) input.

We suggest using the OSD output for setup, then

utilizing the non OSD S-Video output for a better

picture.Any S-Video input also appears at the

Composite Video outputs.The VID6 Record

(S-Video (Y/C)) video output always directs the

chosen MAIN SOURCE’s S-Video signal to a

video recording device.

1.3.2.6 COMPOSITE VIDEO OUTPUTS

a) VID6 RECORD, Output to Composite Video input

of a VCR or other A/V recorder (No OSD)

b) ZONE VID (Some SSP-75 – ZONE2 VID) (No OSD)

c) MONITOR OSD, with On Screen Display

d) MONITOR NO OSD, Main Monitor without On

Screen Display

These Composite Video outputs direct video signals

from various SOURCE components to selected

destinations. The MONITOR Composite outputs

transfer a chosen SOURCE’s Composite signal to

any monitor or TV set with an Composite Video

input. We suggest using the OSD output for setup,

then utilizing the non OSD output for a better

picture. Any picture sent to an S-Video Input also

appears at the Composite Video outputs. The VID6

Record (Composite Video) video output always

directs the MAIN chosen SOURCE’s Composite

signal to a video recording device.

NC3MAH

NC3FAH2

PUSH

NC3FAH2

PUSH

NC3MAH

AUDIO/VIDEO INPUTS

VID1 VID3VID2

VID4 VID6VID5

S-VIDEO INPUTS

COMPOSITE VIDEO INPUTS

OUTPUTS AUDIO INPUTS

RECORD

VID6

AUDIO 1

ZONE2

RECORD

VID6

OSD

MONITORZONE2

VID

AUDIO 2 AUDIO 4AUDIO 3

NO OSD

MONITOR

COAX1

S-VIDEO OUTPUTS

COMPOSITE VIDEO OUTPUTS

SUB

VID2 VID3VID1

VID5 VID6VID4

FRONT SURROUND

RIGHT

CENTER

RECORD

OSD

MONITORVID6

NO OSD

MONITOR

MAIN OUTPUTS

LEFT REAR LEFTRIGHTFRONT

5.1 ANALOG INPUTS

AUDIO 5 FRONT

COAX2 COAX4COAX3

SUB

RECORD

OUT

CENTER

OPTICAL2OPTICAL1

COMPONENT VIDEO

SURROUND

DIGITAL INPUTS

AUDIO INPUTS

RIGHT AUDIO 6

AC-3

COAX

ADAPTOR

LEFT

OPTICAL

OUTPUTS

LEFT

RIGHT

AES/EBU

INPUT1

Cb Cr Y

INPUT2

Cb Cr Y

CENTER SUB

Cb Cr

RS 232 PORT

EXTERNAL CONTROL

MONITOR

RIGHT

LEFT

MIC

A.C. INLET

MAIN

ZONE

IR DC IRDC

BEFORE CONNECTING TO A.C. LINE

ALWAYS TURN OFF UNIT BEFORE

DISCONNECT A.C. LINE BEFORE OPENING UNIT

CHANGING ANY CONNECTIONS

REPLACE FUSE WITH SAME TYPE AND RATING ONLY

CHECK OPERATING VOLTAGE

W A R N I N G