Operating instructions

ManualsBrandsClasse Audio ManualsOtherCA-401

Operating Instructions

audio/video multi-channel receiver

VSX-01TXH_KU.book 1 ページ２００８年４月１６日　水曜日　午後１時５９分

Summary of content (104 pages)

PAGE 1
VSX-01TXH_KU.
PAGE 2
VSX-01TXH_KU.book 2 ページ２００８年４月１６日水曜日午後１時５９分 FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 3
VSX-01TXH_KU.book 3 ページ２００８年４月１６日水曜日午後１時５９分 IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
PAGE 4
VSX-01TXH_KU.book 4 ページ２００８年４月１６日水曜日午後１時５９分 WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm. Wash hands after handling D36-P4_A_En If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted.
PAGE 5
VSX-01TXH_KU.book 5 ページ２００８年４月１６日水曜日午後１時５９分 Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. Contents 01 Before you start 05 Listening to your system Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Checking what’s in the box. . . . . . . . . . . . . . . . . . . .
PAGE 6
VSX-01TXH_KU.book 6 ページ２００８年４月１６日水曜日午後１時５９分 08 Other connections Connecting an iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Connecting your iPod to the receiver . . . . . . . . . . . . 52 iPod playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Connecting a USB device . . . . . . . . . . . . . . . . . . . . . . . 54 Connecting your USB device to the receiver . . . . . . 54 Basic playback controls . . . . . . . . . . . . . . . . . . . . . . .
PAGE 7
VSX-01TXH_KU.book 7 ページ２００８年４月１６日水曜日午後１時５９分 Before you start 01 Chapter 1: Before you start Features • Advanced Direct Energy design This receiver offers a new advancement in discrete design unique to Pioneer for high-power drivability, low distortion and stable imaging.
PAGE 8
VSX-01TXH_KU.book 01 8 ページ２００８年４月１６日水曜日午後１時５９分 Before you start • iPod and USB Ready This receiver has the terminals for connecting an iPod unit and a USB mass storage device. Loading the batteries The iPod terminal is ready for handling digital audio, and this receiver’s enhanced compatibility makes on-screen control of your iPod an added possibility. The USB terminal allows you to listen to two-channel audio from a USB mass storage device connected to this receiver.
PAGE 9
VSX-01TXH_KU.book 9 ページ２００８年４月１６日水曜日午後１時５９分 5 minute guide 02 Chapter 2: 5 minute guide Introduction to home theater Home theater refers to the use of multiple audio tracks to create a surround sound effect, making you feel like you’re in the middle of the action or concert. The surround sound you get from a home theater system depends not only on your speaker setup, but also on the source and the sound settings of the receiver.
PAGE 10
VSX-01TXH_KU.book 10 ページ２００８年４月１６日水曜日午後１時５９分 5 minute guide 02 Automatically setting up for surround sound (Auto MCACC) The Auto MCACC Setup measures the acoustic characteristics of your listening area, taking into account ambient noise, speaker size and distance, and tests for both channel delay and channel level.
PAGE 11
VSX-01TXH_KU.book 11 ページ２００８年４月１６日水曜日午後１時５９分 5 minute guide 1.Auto MCACC Now Analyzing … Environment Check Ambient Noise Microphone Speaker YES/NO 02 • Some older TVs may interfere with the operation of the microphone. If this seems to be happening, switch off the TV when doing the Auto MCACC Setup. 1.
PAGE 12
VSX-01TXH_KU.book 02 12 ページ２００８年４月１６日水曜日午後１時５９分 5 minute guide It is possible to check on the display whether or not multichannel playback is being performed properly. Phase Control ON Front speaker When using a surround back speaker, 2D+PL IIx MOVIE is displayed when playing Dolby Digital signals, and DTS+Neo:6 is displayed when playing DTS 5.1channel signals. Listening position When not using a surround back speaker, DOLBY DIGITAL is displayed when playing Dolby Digital signals.
PAGE 13
VSX-01TXH_KU.book 13 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment 03 Chapter 3: Connecting your equipment This receiver provides you with many connection possibilities, but it doesn’t have to be difficult. This page explains the kinds of components you can connect to make up your home theater system.
PAGE 14
VSX-01TXH_KU.book 03 14 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment 10 Multichannel analog audio inputs 7.1 channel inputs for connection to a DVD player with multichannel analog outputs.  See Using XM Radio on page 55. 11 Speaker terminals Use for connection to the main front, center, surround and surround back speakers.  See Installing your speaker system on page 21. 12 Composite and S-Video monitor outputs Use to connect monitors and TVs.
PAGE 15
VSX-01TXH_KU.book 15 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment • To avoid hum, do not lay connected cables over the top of the receiver. • When connecting optical cables, be careful when inserting the plug not to damage the shutter protecting the optical socket. • When storing optical cable, coil loosely. The cable may be damaged if bent around sharp corners.
PAGE 16
VSX-01TXH_KU.book 03 16 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment Connecting using HDMI If you have an HDMI or DVI (with HDCP) equipped component, you can connect it to this receiver using a commercially available HDMI cable.
PAGE 17
VSX-01TXH_KU.book 17 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment 03 Connecting your TV and DVD player VIDEO IN TV 4 Connect the stereo audio outputs on your DVD player to the DVD AUDIO inputs. Connect using a stereo RCA/phono jack cable. S-VIDEO IN • If your DVD player has multichannel analog outputs, you can connect these instead. See also Using XM Radio on page 55.
PAGE 18
VSX-01TXH_KU.book 03 18 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment Connecting a satellite/cable receiver or other set-top box Connecting a DVD/HDD recorder, VCR and other video sources Satellite and cable receivers, and terrestrial digital TV tuners are all examples of so-called ‘set-top boxes’. This receiver has two sets of audio/video inputs and outputs suitable for connecting analog or digital video devices, including DVD/HDD recorders and VCRs.
PAGE 19
VSX-01TXH_KU.book 19 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment 03 3 If the device can output digital audio, connect an optical-type1 digital audio output from the recorder to the OPTICAL IN 2 (DVR1) input. Use an optical cable for the connection.2 Using the component video jacks Component video should give superior picture quality when compared to composite or S-Video.
PAGE 20
VSX-01TXH_KU.book 03 20 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment 1 Connect a coaxial-type1 digital audio output on your digital component to the COAXIAL IN 2 (CD) input. Use a coaxial cable for the connection. 2 For recording equipment, connect the optical-type DIGITAL output to a digital input on the recorder. Use an optical cable to connect to the OPTICAL OUT.
PAGE 21
VSX-01TXH_KU.book 21 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment 03 Installing your speaker system To take full advantage of the receiver’s surround sound capabilities connect front, center, surround and surround back speakers, as well as a subwoofer.1 Although this is ideal, other configurations with fewer speakers—no subwoofer or no center speaker, or even no surround speakers—will work. At the very least, front left and right speakers only are necessary.
PAGE 22
VSX-01TXH_KU.book 03 22 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment Bare wire connections Make sure that the speaker cable you’re going to use is properly prepared with about 10 mm (3/8 in.) of insulator stripped from each wire, and the exposed wire strands twisted together (fig. A). To connect a terminal, unscrew the terminal a few turns until there is enough space to insert the exposed wire (fig. B). Once the wire is in position, tighten the terminal until the wire is firmly clamped (fig.
PAGE 23
VSX-01TXH_KU.book 23 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment 03 The diagrams below show suggested surround and surround back speaker orientation. The first diagram (fig. A) shows orientation with one surround back speaker (or none) connected. The second (fig. B) shows orientation with two surround back speakers connected. 90° to 120° Connect the AM loop antenna and the FM wire antenna as shown below.
PAGE 24
VSX-01TXH_KU.book 03 24 ページ２００８年４月１６日水曜日午後１時５９分 Connecting your equipment Connecting external antennas To improve FM reception connect an external FM antenna to the FM UNBAL 75 Ω terminal. Plugging in the receiver Only plug in after you have connected all your components to this receiver, including the speakers. Caution • Handle the power cord by the plug part.
PAGE 25
VSX-01TXH_KU.book 25 ページ２００８年４月１６日水曜日午後１時５９分 Controls and displays 04 Chapter 4: Controls and displays Front panel 1 2 3 4 5 6 VSX-01TXH STANDBY/ON PHASE CONTROL DVD ADVANCED MCACC BD TV SAT DIGITAL PRECISION PROCESSING DVR 1/DVR 2 VIDEO HDMI 1/HDMI 2 DIGITAL VIDEO SCALER CD/CD-R FM/AM XM/SIRIUS HDMI iPod USB MULTI CH IN INPUT SELECTOR MASTER VOLUME AUTO SURR/ STREAM DIRECT HOME THX STANDARD SURROUND ADVANCED SURROUND STEREO/ A.L.C.
PAGE 26
VSX-01TXH_KU.book 04 26 ページ２００８年４月１６日水曜日午後１時５９分 Controls and displays 10 MCACC SETUP MIC jack Use to connect the supplied microphone. 11 PHONES jack Use to connect headphones. When the headphones are connected, there is no sound output from the speakers. 12 Listening mode buttons AUTO SURR/STREAM DIRECT – Switches between Auto surround mode (Auto playback on page 30) and Stream Direct playback.
PAGE 27
VSX-01TXH_KU.book 27 ページ２００８年４月１６日水曜日午後１時５９分 Controls and displays 04 Display 1 2 3 4 5 6 7 8 9 10 TUNED PHASE CONTROL DNR L C R 2DIGITAL 2HD DTS WMA9 Pro MULTI-ZONE DIALOG E ATT OVER STEREO MONO SL S SR DSD PCM S.RTRV SOUND V.SB HDMI SBL SB SBR DIGITAL SIRIUS VIDEO CD DVD TV TUNER LFE ANALOG 11 12 AUTO PCM CD-R iPod BDP DVR HDMI [1] dB USB [2] XM SR+ STREAM DIRECT Neo : 6 2PRO LOGIC THX ADV.
PAGE 28
VSX-01TXH_KU.book 04 28 ページ２００８年４月１６日水曜日午後１時５９分 Controls and displays ENTER can be used to enter commands for TV or DTV, and also to select a disc in a multi-CD player. Remote control Press RECEIVER first to access: 12 RECEIVER 1 2 13 DVD BD DVR 1 DVR 2 FM/AM XM TV HDMI CD CD-R SIRIUS iPod USB INPUT SELECT DIMMER 1 2 3 GENRE MCACC SLEEP 4 5 6 SR+ SBch A.ATT 3 7 8 D.
PAGE 29
VSX-01TXH_KU.book 29 ページ２００８年４月１６日水曜日午後１時５９分 Controls and displays RETURN – Press to confirm and exit the current menu screen (also use to return to the previous menu with DVDs or to select closed captioning with DTV). 6 /// (TUNE/ST) /ENTER Use the arrow buttons when setting up your surround sound system (page 38) and the Audio or Video options (page 73 or 74). Also used to control DVD menus/options and for deck 1 of a double cassette deck player.
PAGE 30
VSX-01TXH_KU.book 05 30 ページ２００８年４月１６日水曜日午後１時５９分 Listening to your system Chapter 5: Listening to your system Important • The listening modes and many features described in this section may not be available depending on the current source, settings and status of the receiver. See Listening modes with different input signal formats on page 96 for more on this.
PAGE 31
VSX-01TXH_KU.book 31 ページ２００８年４月１６日水曜日午後１時５９分 Listening to your system • Neural THX – Up to 7.1 channel sound, especially suited to music sources1 • XM HD Surround – Up to 7.
PAGE 32
VSX-01TXH_KU.book 05 32 ページ２００８年４月１６日水曜日午後１時５９分 Listening to your system • ADVANCED GAME – Suitable for video games • SPORTS – Suitable for sports programs Using Front Stage Surround Advance • CLASSICAL – Gives a large concert hall-type sound The Front Stage Surround Advance function allows you to create natural surround sound effects using just the front speakers and the subwoofer.
PAGE 33
VSX-01TXH_KU.book 33 ページ２００８年４月１６日水曜日午後１時５９分 Listening to your system Using Stream Direct Selecting MCACC presets Use the Stream Direct modes when you want to hear the truest possible reproduction of a source. All unnecessary signal processing is bypassed, and you’re left with the pure analog or digital sound source (see Stream direct with different input signal formats on page 101). AUTO/ DIRECT HDD THX STEREO/ BD MENU A.L.C.
PAGE 34
VSX-01TXH_KU.book 05 34 ページ２００８年４月１６日水曜日午後１時５９分 Listening to your system • HDMI – Selects an HDMI signal.1 • Press RECEIVER, then press SBch repeatedly to cycle the surround back channel options. Each press cycles through the options as follows: 2 • PCM – Only PCM signals are output.
PAGE 35
VSX-01TXH_KU.book 35 ページ２００８年４月１６日水曜日午後１時５９分 Listening to your system 05 Standard / THX SBch Processing / Stereo sources Virtual SB Multichannel sources mode 2 Pro Logic IIx 2 Pro Logic Type of source Dolby Digital/DTS/PCM/SACD/WMA9 Pro and DVD-Audio stereo sources Analog 2-channel (stereo) sources DTS-HD Master Audio/DTS-HD/Dolby Digital Plus/Dolby TrueHD/WMA9 Pro encoded and PCM 6.1 ch/7.1 ch sources Dolby Digital Plus/Dolby TrueHD/ WMA9 Pro encoded and PCM 5.
PAGE 36
VSX-01TXH_KU.book 36 ページ２００８年４月１６日水曜日午後１時５９分 Using the tuner 06 Chapter 6: Using the tuner See About Neural – THX Surround on page 94 for more on this. Listening to the radio The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and manual (step) tuning functions. If you already know the frequency of the station you want, see Tuning directly to a station below.
PAGE 37
VSX-01TXH_KU.book 37 ページ２００８年４月１６日水曜日午後１時５９分 Using the tuner 06 4 Press ENTER. After pressing ENTER, the preset class and number stop blinking and the receiver stores the station. Naming station presets For easier identification, you can name your station presets. 1 Choose the station preset you want to name. See Listening to station presets below for how to do this. 2 Press T.EDIT (Tuner Edit). The display shows STATION NAME, then a blinking cursor at the first character position.
PAGE 38
VSX-01TXH_KU.book 38 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu 07 Chapter 7: The System Setup menu • Surround Back System – Specifies how you are using your surround back speakers (see Surround back speaker setting on page 41).
PAGE 39
VSX-01TXH_KU.book 39 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu 07 • THX Speaker (only available when the Custom Menu above is ALL or Speaker Setting) – Select YES if you are using THX speakers (set all speakers to SMALL), otherwise leave it set to NO. 1 Select ‘Auto MCACC’ from the System Setup menu, then press ENTER. If the System Setup screen is not displayed, refer to Making receiver settings from the System Setup menu on page 38. System Setup MENU 1. 2. 3. 4. 5. 6. 7. • Stand.
PAGE 40
VSX-01TXH_KU.book 07 40 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu • See Problems when using the Auto MCACC Setup on page 11 for notes regarding high background noise levels and other possible interference. 5 Wait for the Auto MCACC Setup to finish outputting test tones. A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present in your setup. Try to be as quiet as possible while it’s doing this.
PAGE 41
VSX-01TXH_KU.book 41 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu 07 Press ENTER after you have finished checking each screen. When you’re finished, select RETURN to go back to the System Setup menu. Be sure to disconnect the microphone from this receiver upon completion of the Auto MCACC setup. Caution • The test tones used in the System Setup are output at high volume.
PAGE 42
VSX-01TXH_KU.book 07 42 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu • Standing Wave – Control overly resonant low frequencies in your listening room (see Standing Wave on page 43). The last two settings are specifically for customizing the parameters explained in Acoustic Calibration EQ Adjust on page 43: 3 Select each channel in turn and adjust the levels (+/–10dB) as necessary. Use / to adjust the volume of the speaker you selected to match the reference speaker.
PAGE 43
VSX-01TXH_KU.book 43 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu 07 Listen to the reference speaker and use it to measure the target channel. From the listening position, face the two speakers with your arms outstretched pointing at each speaker. Try to make the two tones sound as if they are arriving simultaneously at a position slightly in front of you and between your arm span.1 When it sounds like the delay settings are matched up, press  to confirm and continue to the next channel.
PAGE 44
VSX-01TXH_KU.book 07 44 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu 3 Select the channel(s) you want and adjust to your liking. 3d.EQ Adjust MCACC : M1 Ch [SBL] :Finish TRM 63 125 250 500 1k 2k 4k 8k 16k dB 63Hz 125Hz 250Hz 500Hz 1kHz 2kHz 4kHz 8kHz 16kHz TRIM [ [ [ [ [ [ [ [ [ 0.0] 0.0] 0.0] 0.0] 0.0 0.0] 0.0] 0.0] 0.0] 0.0] Use / to select the channel. Use / to select the frequency and / to boost or cut the EQ.
PAGE 45
VSX-01TXH_KU.book 45 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu 07 • Reverberance of high vs. low frequencies – Depending on your room, you may find that lower frequencies seem overly reverberant compared to higher frequencies (i.e. your room sounds ‘boomy’). This may result in a skewed frequency analysis if the measurement is done too late. Low frequencies Level High frequencies Acoustic Cal. EQ Pro.
PAGE 46
VSX-01TXH_KU.book 07 46 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu 4 If you selected ‘Reverb View’, you can check the reverb characteristics for each channel. Press RETURN when you’re done. 3e2.Reverb View M1 : EQ OFF Ch L Fq [ 125Hz ] dB 0 80 160ms :Return This appears according to the setting you chose in Reverb Measurement (step 3 on page 45). Use / to select the channel and the frequency you want to check. Use / to go back and forth between the two.
PAGE 47
VSX-01TXH_KU.book 47 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu 07 Checking MCACC preset data Copying MCACC preset data After you have completed Automatically setting up for surround sound (Auto MCACC) on page 10 or Automatic MCACC (Expert) on page 38, you can check your calibrated settings using the on-screen display. If you want to manually adjust the Acoustic Calibration EQ (see Manual MCACC setup on page 41), we recommend copying your current settings1 to an unused MCACC preset.
PAGE 48
VSX-01TXH_KU.book 48 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu 07 Speaker Setting Manual speaker setup This receiver allows you to make detailed settings to optimize the surround sound performance. You only need to make these settings once (unless you change the placement of your current speaker system or add new speakers).
PAGE 49
VSX-01TXH_KU.book 49 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu 07 • SW – LFE signals and bass frequencies of channels set to SMALL are output from the subwoofer when YES is selected. Choose the PLUS setting if you want the subwoofer to output bass sound continuously or you want deeper bass (the bass frequencies that would normally come out the front and center speakers are also routed to the subwoofer).
PAGE 50
VSX-01TXH_KU.book ２００８年４月１６日水曜日午後１時５９分 The System Setup menu Select ‘X-Curve’ from the Manual SP Setup menu. 5.Manual SP Setup 5d.X-Curve :Return Important • When Speaker Distance is selected while MCACC is set to OFF, the selection screen for the MCACC memory appears. Select a memory to adjust manually. 5c.Speaker Distance Select MCACC memory. 8k 4k 16k 2k -2.0dB/oct 1k X-Curve Speaker Setting Channel Level Speaker Distance X-Curve THX Audio Setting 63 a. b. c. d. e.
PAGE 51
VSX-01TXH_KU.book 51 ページ２００８年４月１６日水曜日午後１時５９分 The System Setup menu 07 3 Specify the distance of your surround back speakers from each other. 5e.THX Audio Setting Loudness Plus SB SP Position [ ON ] 0 - 1 ft :Finish • 0 – 1 ft – Surround speakers within 1 foot apart (best for THX surround sound). • > 1 – 4 ft – Surround speakers between 1 and 4 feet apart. • 4 ft < – Surround speakers more than 4 feet apart. 4 When you’re finished, press RETURN. You will return to the Manual SP Setup menu.
PAGE 52
VSX-01TXH_KU.book 08 52 ページ２００８年４月１６日水曜日午後１時５９分 Other connections Chapter 8: Other connections Connecting your iPod to the receiver Caution • Before making or changing the connections, switch off the power and disconnect the power cord from the power outlet. Plugging in components should be the last connection you make with your system. • Do not allow any contact between speaker wires from different terminals.
PAGE 53
VSX-01TXH_KU.book 53 ページ２００８年４月１６日水曜日午後１時５９分 Other connections 1 Use / to select a category, then press ENTER to browse that category. • To return to the previous level any time, press RETURN. 2 Use / to browse the selected category (e.g., albums). • Use / to move to previous/next levels. 3 Continue browsing until you arrive at what you want to play, then press  to start playback.
PAGE 54
VSX-01TXH_KU.book 54 ページ２００８年４月１６日水曜日午後１時５９分 Other connections 08 Basic playback controls Connecting a USB device 1 It is possible to listen to two-channel audio using the USB interface on the front of this receiver. Connect a USB mass storage device2 as shown below. • Push down on the PUSH OPEN tab to access the iPod DIRECT USB terminal. AUTO SURR/ STREAM DIRECT HOME THX STANDARD SURROUND ADVANCED SURROUND STEREO/ A.L.C.
PAGE 55
VSX-01TXH_KU.book 55 ページ２００８年４月１６日水曜日午後１時５９分 Other connections Compressed audio compatibility Note that although most standard bit/sampling rate combinations for compressed audio are compatible, some irregularly encoded files may not play back. The list below shows compatible formats for compressed audio files: • MP3 (MPEG-1/2/2.5 Audio Layer 3) – Sampling rates: 8 kHz to 48 kHz; Bit rates: 8 kbps to 320 kbps (128 kbps or higher recommended); File extension: .
PAGE 56
VSX-01TXH_KU.book 08 56 ページ２００８年４月１６日水曜日午後１時５９分 Other connections 2 Press XM to switch to the XM Radio input. For best reception, you may need to move the XM MiniTuner antenna near a window (the southernmost window should produce the best results). • If after pressing XM the display shows Check XM Tuner, try disconnecting the receiver and tuner connections, and then plugging them back in.
PAGE 57
VSX-01TXH_KU.book 57 ページ２００８年４月１６日水曜日午後１時５９分 Other connections 08 Using the XM Menu Connecting your SiriusConnect™ Tuner The XM Menu provides additional XM Radio features. To receive SIRIUS Satellite Radio broadcasts, you will need to activate your SiriusConnect™ tuner.1 1 Press TOP MENU. 2 Use / to select a menu item, then press ENTER.
PAGE 58
VSX-01TXH_KU.book 08 58 ページ２００８年４月１６日水曜日午後１時５９分 Other connections Listening to SIRIUS Radio After connecting, you will be able to use this receiver to select channels and navigate categories using the onscreen display.1 The information displayed is as follows: SIRIUS A Decades A0 The '50s 005 Current preset class Signal strength Category Preset number 4 Press ENTER. After pressing ENTER, the preset class and number stop blinking and the receiver stores the SIRIUS channel.
PAGE 59
VSX-01TXH_KU.book 59 ページ２００８年４月１６日水曜日午後１時５９分 Other connections 08 Connecting the multichannel analog inputs For DVD Audio and SACD playback, your DVD player may have 5.1, 6.1 or 7.1 channel analog outputs (depending on whether your player supports surround back channels).1 Make sure that the player is set to output multichannel analog audio. 1 Connect the front, surround, center and subwoofer outputs on your DVD player to the corresponding MULTI CH IN jack on this receiver.
PAGE 60
VSX-01TXH_KU.book 08 60 ページ２００８年４月１６日水曜日午後１時５９分 Other connections • Use the SPEAKERS button on the front panel to select a speaker system setting. As mentioned above, if you have selected Normal, the button will simply switch your main speaker system (A) on or off. AUTO SURR/ STREAM DIRECT HOME THX STANDARD SURROUND ADVANCED SURROUND STEREO/ A.L.C.
PAGE 61
VSX-01TXH_KU.book 61 ページ２００８年４月１６日水曜日午後１時５９分 Other connections 08 Connecting additional amplifiers MULTI-ZONE listening This receiver has more than enough power for any home use, but it’s possible to add additional amplifiers to every channel of your system using the pre-outs. Make the connections shown below to add amplifiers to power your speakers. This receiver can power up to two independent systems in separate rooms after you have made the proper MULTIZONE connections.
PAGE 62
VSX-01TXH_KU.book 08 62 ページ２００８年４月１６日水曜日午後１時５９分 Other connections MULTI-ZONE listening options • Connect a TV monitor to the ZONE 2 VIDEO OUT jacks on the rear of this receiver. You should have a pair of speakers attached to the surround back speaker terminals as shown below. The following table shows what you can listen to in the sub zone: Sub Zone Input sources available ZONE2 iPod, XM or SIRIUS Radio, the built-in tuner and other analog audio sources.
PAGE 63
VSX-01TXH_KU.book 63 ページ２００８年４月１６日水曜日午後１時５９分 Other connections 2 Press CONTROL. • When the receiver is on,1 make sure that any operations for the sub zone are done while ZONE 2 shows in the display. If this is not showing, the front panel controls affect the main zone only. 3 Use the INPUT SELECTOR dial to select the source for the zone you have selected. For example, ZONE 2 CD-R sends the source connected to the CD-R inputs to the sub room (ZONE 2).
PAGE 64
VSX-01TXH_KU.book 08 64 ページ２００８年４月１６日水曜日午後１時５９分 Other connections Switching components on and off using the 12 volt trigger Using this receiver with a Pioneer flat panel TV You can connect components in your system (such as a screen or projector) to this receiver so that they switch on or off using 12 volt triggers when you select an input function. However, you must specify which input functions switch on the trigger using the The Input Setup menu on page 69.
PAGE 65
VSX-01TXH_KU.book 65 ページ２００８年４月１６日水曜日午後１時５９分 Other connections 08 • Use a 3-ringed miniplug SR+ cable to connect the CONTROL IN jack of this receiver with the CONTROL OUT jack of your flat panel TV. Using the SR+ mode with a Pioneer flat panel TV When connected using an SR+ cable, a number of features become available to make using this receiver with your Pioneer flat panel TV even easier.
PAGE 66
VSX-01TXH_KU.book 08 66 ページ２００８年４月１６日水曜日午後１時５９分 Other connections Connecting a PC for Advanced MCACC output Use a commercially-available cable to connect the RS-232C jack on your computer to the 9-pin RS-232C jack on this receiver. See the documentation provided with the Advanced MCACC application for more information.
PAGE 67
VSX-01TXH_KU.book 67 ページ２００８年４月１６日水曜日午後１時５９分 HDMI Control 09 Chapter 9: HDMI Control Important • The KURO LINK function name used on the web and in catalogues is referred to as HDMI Control in the operating instructions and on the product. • To get the most out of this function, we recommend that you connect your HDMI component not to a flat panel TV but rather directly to the HDMI terminal on this receiver.
PAGE 68
VSX-01TXH_KU.book 68 ページ２００８年４月１６日水曜日午後１時５９分 HDMI Control 09 1 Press RECEIVER, then press the SETUP button. Synchronized amp mode operations 2 Select ‘Other Setup’, then press ENTER. By connecting a component to this receiver with an HDMI cable you can use synchronized amp mode, which allows you to synchronize the following operations2: 3 Select ‘HDMI Control Setup’ from the Other Setup menu. 7.Other Setup a. b. c. d. e. 7d.
PAGE 69
VSX-01TXH_KU.book 69 ページ２００８年４月１６日水曜日午後１時５９分 Other Settings 10 Chapter 10: Other Settings The Input Setup menu You only need to make settings in the Input Setup menu if you didn’t hook up your digital equipment according to the default settings (see Input function default and possible settings on page 70). In this case, you need to tell the receiver what equipment is hooked up to which terminal so the buttons on the remote correspond to the components you’ve connected.
PAGE 70
VSX-01TXH_KU.book 10 70 ページ２００８年４月１６日水曜日午後１時５９分 Other Settings Input function default and possible settings The terminals on the rear of the receiver generally correspond to the name of one of the input source functions. If you have connected components to this receiver differently from (or in addition to) the defaults below, see The Input Setup menu on page 69 to tell the receiver how you’ve connected up. The dots () indicate possible assignments.
PAGE 71
VSX-01TXH_KU.book 71 ページ２００８年４月１６日水曜日午後１時５９分 Other Settings 10 Multi Channel Input Setup ZONE Audio Setup You can adjust the level of the subwoofer for a multichannel input. If you’ve made MULTI-ZONE connections (see MULTIZONE listening on page 61) you may need to specify your volume setting. 1 Select ‘Multi Ch In Setup’ from the Other Setup menu. 1 Select ‘ZONE Audio Setup’ from the Other Setup menu. 7.Other Setup a. b. c. d. e. 7.
PAGE 72
VSX-01TXH_KU.book 72 ページ２００８年４月１６日水曜日午後１時５９分 Other Settings 10 SR+ Setup for Pioneer flat panel TVs OSD Adjustment Make the following settings if you have connected a Pioneer flat panel TV to this receiver using an SR+ cable. Note that the number of function settings available will depend on the flat panel TV you’ve connected. Use this feature to adjust your TV display if it seems difficult to see all the instructions on the screen.
PAGE 73
VSX-01TXH_KU.book 73 ページ２００８年４月１６日水曜日午後１時５９分 Using other functions 11 Chapter 11: Using other functions Setting Setting the Audio options There are a number of additional sound settings you can make using the Audio Parameter menu. The defaults, if not stated, are listed in bold. Important • Note that if a setting doesn’t appear in the Audio Parameter menu, it is unavailable due to the current source, settings and status of the receiver.
PAGE 74
VSX-01TXH_KU.book 11 74 ページ２００８年４月１６日水曜日午後１時５９分 Using other functions Setting What it does DRC (Dynamic Range Control) Adjusts the level of dynamic range for movie soundtracks optimized for Dolby Digital, DTS, Dolby Digital Plus, Dolby TrueHD, DTS-HD and DTS-HD Master Audio (you may need to use this feature when listening to surround sound at low volumes).
PAGE 75
VSX-01TXH_KU.book 75 ページ２００８年４月１６日水曜日午後１時５９分 Using other functions Setting What it does Converts video signals for output V. CONV (Digital from the MONITOR OUT jacks for Video all video types. Conversion) 11 Option(s) ON OFF BRIGHT Adjusts the overall brightness. (Brightness) –10 to +10 Default: 0 CONTRAST Adjusts the contrast between light and dark. –10 to +10 Default: 0 HUE Adjusts the red/green balance. –10 to +10 Default: 0 CHROMA Adjusts saturation from dull to bright.
PAGE 76
VSX-01TXH_KU.book 11 76 ページ２００８年４月１６日水曜日午後１時５９分 Using other functions Reducing the level of an analog signal The input attenuator lowers the input level of an analog signal when it’s too strong. You can use this if you find the that the OVER indicator is lights often, or you can hear distortion in the sound.1 1 2 3 GENRE MCACC SLEEP 4 5 6 SR+ SBch A.ATT 7 8 9 D.
PAGE 77
VSX-01TXH_KU.book 77 ページ２００８年４月１６日水曜日午後１時５９分 Using other functions 11 Setting Default Resetting the system Sound Delay 0.0 frame Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this. Dual Mono CH1 DRC OFF 1 Switch the receiver into standby. SACD Gain 0 dB 2 While holding down the front panel STEREO/A.L.C button, press and hold  STANDBY/ON for about two seconds. The display shows RESET?.
PAGE 78
VSX-01TXH_KU.book 12 78 ページ２００８年４月１６日水曜日午後１時５９分 Controlling the rest of your system Chapter 12: Controlling the rest of your system Setting the remote to control other components Most components can be assigned to one of the input source buttons (such as DVD or CD) using the component’s manufacturer preset code stored in the remote.
PAGE 79
VSX-01TXH_KU.
PAGE 80
VSX-01TXH_KU.book 12 80 ページ２００８年４月１６日水曜日午後１時５９分 Controlling the rest of your system Button(s) Function Components CH +/– Selects channels. Cable TV/ Satellite TV/TV/ DTV VOL +/– Adjust the TV volume. SOURCE Switches the DTV on or off. Cable TV/ Satellite TV/TV/ DTV This remote control can control these components after entering the proper codes or teaching the receiver the commands (see Setting the remote to control other components on page 78 for more on this).
PAGE 81
VSX-01TXH_KU.book 81 ページ２００８年４月１６日水曜日午後１時５９分 Controlling the rest of your system Button(s) Function Components ENTER/ CLASS Chooses the disc. Multiple CD player Use as the ENTER button. VCR/DVD/BD player Displays the setup screen for DVR DVR player players. Changes sides of the LD. LD player 12 1 Decide which component you want to use the remote sensor of.
PAGE 82
VSX-01TXH_KU.book 13 82 ページ２００８年４月１６日水曜日午後１時５９分 Additional information Chapter 13: Additional information Troubleshooting Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used.
PAGE 83
VSX-01TXH_KU.book 83 ページ２００８年４月１６日水曜日午後１時５９分 Additional information Symptom 13 Remedy No sound from the surround or • Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t selected; center speakers. select one of the surround listening modes (see Listening in surround sound on page 30). • Check that the surround/center speakers are not set to NO (see Speaker Setting on page 48). • Check the channel level settings (see Channel Level on page 49).
PAGE 84
VSX-01TXH_KU.book 13 84 ページ２００８年４月１６日水曜日午後１時５９分 Additional information Other audio problems Symptom Remedy Broadcast stations cannot be selected automatically, or there is considerable noise in radio broadcasts. For FM broadcasts • Fully extend the FM wire antenna, adjust the position for best reception and secure to a wall, etc. • Use an outdoor antenna for better reception (see page 24). For AM broadcasts • Adjust the position and direction of the AM antenna.
PAGE 85
VSX-01TXH_KU.book 85 ページ２００８年４月１６日水曜日午後１時５９分 Additional information 13 Video Symptom Remedy No image is output when an input is selected. • Check the video connections of the source component (see page 18). • For high-definition video (using component video connections), or when digital video conversion is switched off (in Setting the Video options on page 74), you must connect your TV to this receiver using the same type of video cable as you used to connect your video component.
PAGE 86
VSX-01TXH_KU.book 13 86 ページ２００８年４月１６日水曜日午後１時５９分 Additional information Professional Calibration EQ graphical output Symptom Remedy The EQ response displayed in the graphical output following calibration does not appear entirely flat. • There are cases where the graph does not appear flat (even when selecting ALL CH ADJUST in the Auto MCACC Setup) due to adjustments made to compensate for room characteristics to achieve optimal sound.
PAGE 87
VSX-01TXH_KU.book 87 ページ２００８年４月１６日水曜日午後１時５９分 Additional information Symptom Remedy When playing certain discs, none of the receiver’s format indicators light. • The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on what audio tracks are recorded on the disc. 13 When playing a disc with the • Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 33).
PAGE 88
VSX-01TXH_KU.book 13 88 ページ２００８年４月１６日水曜日午後１時５９分 Additional information HDMI 88 En Symptom Remedy The HDMI indicator blinks continuously. • Check all the points below. No picture or sound. • This receiver is HDCP-compatible. Check that the components you are connecting are also HDCPcompatible. If they are not, please connect them using the component, S-Video or composite video jacks.
PAGE 89
VSX-01TXH_KU.book 89 ページ２００８年４月１６日水曜日午後１時５９分 Additional information Important information regarding the HDMI connection There are cases where you may not be able to route HDMI signals through this receiver (this depends on the HDMIequipped component you are connecting–check with the manufacturer for HDMI compatibility information). If you aren’t receiving HDMI signals properly through this receiver (from your component), please try one of the following configurations when connecting up.
PAGE 90
VSX-01TXH_KU.book 13 90 ページ２００８年４月１６日水曜日午後１時５９分 Additional information Symptom Cause Action CH Unavailable The selected channel is not available. The channel may have been reassigned to a different channel number. This message may occur initially with a new radio or a radio that has not received XM’s signal for an extended period. Consult the latest channel guide at www.xmradio.com for the current list of channels.
PAGE 91
VSX-01TXH_KU.book 91 ページ２００８年４月１６日水曜日午後１時５９分 Additional information Surround sound formats Below is a brief description of the main surround sound formats you’ll find on DVDs, satellite, cable and terrestrial broadcasts, and video cassettes. Dolby The Dolby technologies are explained below. See www.dolby.com for more detailed information. Dolby Digital Dolby Digital is a multichannel digital audio coding system widely used in cinemas, and in the home for DVD and digital broadcast soundtracks.
PAGE 92
VSX-01TXH_KU.book 13 92 ページ２００８年４月１６日水曜日午後１時５９分 Additional information Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “Surround EX” and the double-D symbol are trademarks of Dolby Laboratories. DTS The DTS technologies are explained below. See www.dtstech.com for more detailed information. DTS-EXPRESS DTS-EXPRESS is a low-bitrate encoding technology supporting up to 5.1 channels with fixed data transfer rates.
PAGE 93
VSX-01TXH_KU.book 93 ページ２００８年４月１６日水曜日午後１時５９分 Additional information About THX The THX technologies are explained below. See www.thx.com for more detailed information. • THX Cinema processing THX is an exclusive set of standards and technologies established by THX Ltd. THX grew from George Lucas’ personal desire to make your experience of the film soundtrack, in both movie theatres and in your home theatre, as faithful as possible to what the director intended.
PAGE 94
VSX-01TXH_KU.book 94 ページ２００８年４月１６日水曜日午後１時５９分 Additional information 13 • THX Loudness Plus Description THX Loudness Plus is a new volume control technology featured in THX Ultra2 Plus™ and THX Select2 Plus™ Certified amplifiers. With THX Loudness Plus, home theater audiences can now experience the rich details in a surround mix at any volume level. A consequence of turning the volume below Reference Level is that certain sound elements can be lost or perceived differently by the listener.
PAGE 95
VSX-01TXH_KU.book 95 ページ２００８年４月１６日水曜日午後１時５９分 Additional information About XM 13 your XM Ready audio system on for up to an hour. When you can access the full lineup on your XM Ready audio system you are done. XM Ready® is a registered trademark of XM Satellite Radio Inc. The XM® name and related logo are registered trademarks of XM Satellite Radio Inc. All rights reserved. About SIRIUS U.S.
PAGE 96
VSX-01TXH_KU.book 13 96 ページ２００８年４月１６日水曜日午後１時５９分 Additional information Listening modes with different input signal formats The following charts outline the listening modes available with different input signal formats, depending on the surround back channel processing and decoding method you have selected. Stereo (2 channel) signal formats SBch Processing Input signal format Standard THX Auto Surround SBch Processing ON/AUTO (Automatically selects 6.1/7.
PAGE 97
VSX-01TXH_KU.book 97 ページ２００８年４月１６日水曜日午後１時５９分 Additional information 13 SBch Processing Input signal format Standard THX Auto Surround SBch Processing OFFd Dolby Digital Plus Dolby TrueHD (except for 176.4 kHz/ 192 kHz) 2 Pro Logic ll MOVIE 2 Pro Logic ll MUSIC 2 Pro Logic ll GAME 2 PRO LOGIC 2 PRO LOGIC+THX 2 Pro Logic ll MOVIE+THX CINEMA 2 Pro Logic ll MUSIC+THX MUSIC 2 Pro Logic ll GAME+THX GAMES Neo:6 MUSIC+THX MUSIC Neo:6 CINEMA+THX Stereo playback Dolby TrueHD (176.
PAGE 98
VSX-01TXH_KU.book 13 98 ページ２００８年４月１６日水曜日午後１時５９分 Additional information Multichannel signal formats SBch Processing Input signal format Standard THX Auto Surround SBch Processing ON (7.1 channel decoding used for all sources) Dolby Digital Plus Dolby TrueHD DTS-HD DTS-HD Master Audio WMA9 Pro PCM (6.1/7.1 channel) Straight decoding THX CINEMA THX MUSIC THX GAMES Straight decoding Dolby Digital Plus Dolby TrueHD (except for 176.4 kHz/ 192 kHz) (5.
PAGE 99
VSX-01TXH_KU.book 99 ページ２００８年４月１６日水曜日午後１時５９分 Additional information 13 SBch Processing Input signal format Standard SBch Processing ON (7.1 channel decoding used for all sources) DTS-ES (6.1 channel sources/ 6.
PAGE 100
VSX-01TXH_KU.book 13 100 ページ２００８年４月１６日水曜日午後１時５９分 Additional information SBch Processing Input signal format Standard THX Auto Surround SBch Processing AUTO (Automatically selects 6.1/7.1 channel decoding) Dolby Digital Plus Dolby TrueHD DTS-HD DTS-HD Master Audio WMA9 Pro PCM (6.1/7.1 channel) Straight decoding THX CINEMA Straight decoding Dolby TrueHD (176.4 kHz/192 kHz) (5.
PAGE 101
VSX-01TXH_KU.book 101 ページ２００８年４月１６日水曜日午後１時５９分 Additional information 13 Stream direct with different input signal formats The following charts show what you will hear with different input signal formats, depending on the Stream Direct mode (see Using Stream Direct on page 33) you have selected.
PAGE 102
VSX-01TXH_KU.book 13 102 ページ２００８年４月１６日水曜日午後１時５９分 Additional information FM Tuner Section Specifications Amplifier section Continuous average power output of 110 watts* per channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no more than 0.09 %** total harmonic distortion (front). Continuous Power Output (20 Hz to 20 kHz, 8 Ω, 0.09 %) Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 W Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 103
VSX-01TXH_KU.book 103 ページ２００８年４月１６日水曜日午後１時５９分 Additional information 13 We Want You Listening For A Lifetime Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level.
PAGE 104
VSX-01TXH_KU.book 104 ページ２００８年４月１６日水曜日午後１時５９分 Should this product require service in the U.S.A. and you wish to locate the nearest Pioneer Authorized Independent Service Company, or if you wish to purchase replacement parts, operating instructions, service manuals, or accessories, please call the number shown below.