Owner manual

ManualsBrandsClarus Environmental ManualsPumpsTurbine STEP Systems

Final Assembly

Electrical Data for Clarus Environmental Turbine Efuent Pumps

HP Volts Ph Hz S.F.

Maximum

Locked

Rotor

Amps

KVA

Code

Fuse/Circuit

Breaker Amps

Winding

Resistance

Line to Line

Amps Watts Std. Delay

1/2 115 1 60 1.6 12 970 64.4 R 30 15 1.0 - 1.3

1/2 230 1 60 1.6 6 970 32.2 R 15 8 4.2 - 5.2

3/4 230 1 60 1.5 8 1325 40.7 N 20 10 3.0 - 3.6

1 230 1 60 1.4 9.8 1600 48.7 N 25 11 2.2 - 2.7

1 1/2 230 1 60 1.3 13.1 2250 56.8 L 35 15 1.5 - 1.9

2 230 1 60 1.25

Y 13.2

B 11.9

R 2.6

2650 51.0 G 30 15

1.6 - 2.3 M

5.2 - 7.15 S

3 230 1 60 1.15

Y 14.0

B 14.5

R 4.5

3650 82.0 G 45 20

.9 - 1.5 M

3.0 - 4.9 S

FILTER HOLDER

FILTER TANK

ATTACH FLOAT TREE RIGHT BELOW

THE FILTER HOLDER FITTING

TILT FILTER HOLDER TO LOCATE

IN ANTI-FLOTATION POCKET

SK2416

Fig. 12

Wiring Instructions

16. Place the lter holder assembly down in the pump vault, tilting it

toward the pump well side to allow the handle to be placed into the

anti-otation pocket (see Fig. 1 & 13).

17. Place the oat tree assembly down into the pump vault. The bottom

of the oat tree must go into the top of the lter holder. Snap the

top of the oat tree to the lter holder handle (see Fig. 1 & 12).

18. Connect the pump, oats, alarms and control panels. Follow in-

stallation instructions and wiring diagrams supplied with each.

19. After wiring, ll the septic tank with water. This must be done to

check the pump, oat operating levels and the alarm. Be sure the

oats do not hang up during operation! Do not fully empty

the septic tank of water to help prevent oat-out.

"Risk of electrical shock" Do not remove

the power supply cord and strain relief or connect conduit di-

rectly to the pump. Installation and checking of electrical cir-

cuits and hardware should be performed by a qualied and licensed

electrician.

For your protection, make certain that the

pump ground wire is properly connected to the ground

wire in the incoming power line. Test for ground at the junc-

tion box using an Underwriters Laboratory listed circuit ana-

lyzer which will indicate if the power, neutral and ground wires are cor-

rectly connected.

In 230 VAC pump installations, one side of

the line going to the pump is always hot. This condition exists

if the switch is on or off. Install a double pole disconnect on all

230 VAC pump circuits.

GENERAL WIRING RECOMMENDATIONS

• Follow the correct wiring diagram for your system.

• Use an auxiliary alarm with the double piggyback oat switch op-

tion or any other control method that does not include a high water

alarm. Install the alarm inside the house or in a weather protected

location per installation instructions with the alarm kit. Make sure

the alarm is plugged into a different circuit than the pump circuit.

• If a junction box is being used, follow the installation instructions

and wiring directions with the junction box or follow the directions

below. All wiring, from the power source to the pump, must conform

to the National Electrical Code.

• Be sure to leave a sufcient amount of cord so the lter can be

serviced without disconnecting the cordage from the junction box

(see maintenance section).

LIQUID-TIGHT

CONNECTOR

115V

PUMP

115V

POWER

SOURCE

BLACK

RED

WHITE

115V

SWITCH

L1 N

JUNCTION BOX

RED

LIQUID-TIGHT

CONNECTOR

230V

PUMP

230V

POWER

SOURCE

BLACK

WHITE

230V

SWITCH

JUNCTION BOX

120 VAC

230 VAC

Double Piggyback Float Switch Installations

SK1837A

SK1837B