POWERWASHER Model: PLV100LB Part No: 7330658 OPERATING & MAINTENANCE INSTRUCTIONS 0606
-2-
Thank you for selecting this CLARKE Power Washer for your cleaning requirements. This booklet contains important information about its operation and maintenance and should be read in conjunction with a similar guide produced by the manufacturers of the engine fitted to this particular unit. Please read both of these carefully before using the machine. GUARANTEE This CLARKE product is guaranteed against faults in manufacture for twelve months from the date of purchase.
GENERAL SAFETY PRECAUTIONS WARNING: Water at high pressure can be dangerous and can cause damage to persons or property if the operator is careless. Never allow anyone to operate this equipment unless they are thoroughly reliable, and familiar with the safety precautions. ✗ ✗ ✗ ✗ ✗ ✗ ✗ ✗ ✔ ✔ ✔ ✔ ✔ NEVER direct the spray towards any person or animal. NEVER direct the spray towards electrical wiring or equipment. NEVER hold your finger over the high pressure nozzle. NEVER allow children to use this machine.
ASSEMBLY and PREPARATION FOR USE. Contents B B1 A C D F E G H L I K J M N ‘A’ Engine with Mounting Plate. ‘H’ Lance. ‘B’ Handle. ‘I’ Nozzle cleaning pin. ‘B1’ Engine Frame ‘J’ Upper tool holder. ‘C’ Wheel x 2. ‘K’ Foot x 2. ‘D’ Wheel Cap x 2. ‘L’ Gun. ‘E’ Self tapping screw x 5. ‘M’ Wheel assembly drift. ‘F’ High pressure hose. ‘N’ Lower tool holder. ‘G’ Securing Washer x 2. Fig. 1 The power washer requires a small amount of assembly before using as follows. 1.
4. Carefully turn the chassis onto one side to access the axle to enable wheel to be fitted. Slide wheel onto axle as shown, ensuring the flat side is on the inside as in Fig. 2 to allow the cap to be fitted. Fig. 2 Fig. 3 5. Place the wheel securing washer in the drift as shown, ensuring the concave side faces outwards. 6. Position the washer centrally on the axle, gently using a suitable hammer/mallet, drive the washer onto the axle as in Fig. 4.
13. Slide the upper tool holder up into position and secure with self tapping screw. Fig. 7 Fig. 8 14. Assemble the lance to the gun with a simple bayonet connection Fig .8. Attach one end of the high pressure hose to the gun Fig. 8a and tighten the securing nut using a 17mm open ended spanner, DO NOT overtighten. Connect other end of the high pressure hose to the pump Fig .8b, hand tight only. Detergent Hose Fig. 8b Fig. 8a 15.
6. Pull the starter with a quick firm action. Allow the cord to recoil fully into its housing whilst retaining a grip on the handle. Repeat operation until the engine starts. Fig. 10 As soon as the engine starts, slowly move the throttle lever back towards stop until the engine is running at a reasonable tick over speed and not racing flat out. NOTE: 1. If there is any difficulty in starting the engine, get an assistant to fully depress the gun trigger whilst you attempt to start.
MAINTENANCE Very little regular maintenance is required, other than general cleaning on the outside of the machine. Wipe over with a clean dampened soft cloth, use a mild household detergent if necessary. Never use harmful chemicals. If detergents have been used in the washer, it is important to flush the system with clean water for a few minutes after use. If there is a danger of freezing, anti freeze should be mixed with the flush water, or the system must be completely drained.
PARTS LIST & DIAGRAM (PUMP) No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 21 22 23 24 Gasket Flange with ‘O’ ring Oil Seal D.17X35X7 Bearing 6205-2Z Vertical Plate Bearing Disk AS4565 Needle Bearing Thrust Shoe D.65 Piston Assembly ‘O’ Ring Gasket Piston Recall Spring Seal Seat ‘O’ Ring Gasket Spring X T.S. Brass Piston D.11 ‘O’ Ring 7.66 x 1.78 ‘O’ Ring X T.S. Piston & Valve Seat Gasket Rubber Holder Sphere Inox Spring Piston Guide Qty Part No.
PARTS LIST & DIAGRAM (CHASSIS) 1 9 8 28 2 27 14 17 & 18 4 19 12 4 3 7 5 6 13 16 11 10 29 3 15 No. Description Qty Part No. No. Description Qty Part No. 1 Handle 1 LW5.013.0049 13 Wheel Cap 2 LW3.099.0095 2 Upper Lance Holder 1 LW4.008.0732 14 Nut 6 LW3.003.0017 3 Self Tapping Screw 5 LW3.002.0024 15 Detergent Hose 1 LW4.008.0005 4 Screw M8 x 60 3 LW3.002.0120 16 Foot 2 LW4.008.0730 5 Lower Lance Holder 1 LW4.008.0731 17 Gun 1 LW6.001.
