CHAINSAW SHARPENER MODEL: ECSS-1 Part No: 3402075 ASSEMBLY & INSTRUCTION MANUAL LS0409
INTRODUCTION Thank you for purchasing this CLARKE product Before attempting to use the product, it is essential that you read this manual thoroughly and carefully follow all instructions given. In doing so you will ensure the safety of yourself and that of others around you, and you can also look forward to the product giving you long and satisfactory service. GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
CONTENTS INTRODUCTION .............................................................................................. 2 GUARANTEE ................................................................................................... 2 ENVIRONMENTAL PROTECTION .................................................................... 2 PARTS & SERVICE ........................................................................................... 2 SAFETY PRECAUTIONS ........................................................
OPERATING HINTS • Before you sharpen the chainsaw chain check it for damages, such as: - bent or abraded chain links. - broken cutting teeth, loose rivets or broken rivet heads. If any damage is found, replace the entire chain. • A sharp chainsaw produces wood chips and pulls itself into the timber being cut. When it becomes blunt, sawdust will start being produced during cutting operations.
ELECTRICAL CONNECTIONS WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage. This product may be fitted with a non-rewireable plug.
PARTS IDENTIFICATION D C E B F H I J K L O A F N G I M A Base Plate I Adjusting Screw B ON/OFF Switch J Chain Holder Assembly C Handle K Angle Indicator D Protective Cover L Angle Adjustment Screw E Grinding Disc M Guide Boards F Fastening Screw N Depth Limiter G Adjustment Wedge O Mounting Holes H Chain Holder 6
ASSEMBLY The chain saw sharpener is supplied only partly assembled. 1. Remove the bolts from both pivot clamps as shown in Fig 4. 2. Insert the axle into the body of the chainsaw sharpener. Fig 5. 3. Place the chainsaw sharpener on the base plate. • Make sure the nipple on the chainsaw sharpener is positioned inside the depth limiter (N) spring as shown in Fig 6. Fig 4 Fig 5 4. Replace the pivot clamps and secure in place using the bolts removed in step 1.
OPERATING WHEN SHARPENING, ALWAYS WEAR SAFETY GOGGLES. FITTING THE CHAIN TO THE SHARPENER Fig 8 1. Lift up the adjustment wedge (G) and unscrew the fastening screw (F), see Fig 8. 2. Place the chainsaw chain on the chain holder assembly (J). • There is a diagram on the chainsaw holder indicating which way the teeth should be facing ADJUSTMENTS Fig 9 ADJUSTING THE GRINDING ANGLE 1. Rotate the chain holder assembly (J) to the required angle.
SWITCHING ON/OFF Fig 10 6. To switch on, set the ON/OFF switch to the ( I ) position. see Fig 10 7. To switch off, set the ON/OFF switch to the ( O ) position. see Fig 10 SHARPENING THE CHAIN 8. Make sure the chainsaw chain is held securly between both guide boards (M). Tighten with the fastening screw (F) if nessecery. see Fig 11. Fig 11 9. Position the tooth being sharpened near to the grinding disc. 10.
MAINTENANCE AND CLEANING • Use a dry paint-brush to clean the unit and remove grinding residues. • Do not clean the unit with aggressive detergents or chemicals. • The unit does not require any lubrication. CHANGING THE GRINDING DISC BEFORE CARRYING OUT ANY WORK ON THE CHAIN SAW SHARPENER DISCONNECT THE PLUG FROM MAINS SUPPLY. 1. Unscrew the bolts indicated using the hexagonal key supplied and remove the protective cover (D). See Fig 14. Fig 14 Fig 15 2.
SPECIFICATION Nominal Voltage ...................................... 230 V Frequency ................................................. 50 Hz Nominal Power ......................................... 130 W No Load Speed ........................................ 3000 rpm Disc Diameter ........................................... Ø 100 mm Weight ....................................................... 2.5 kg Protection Class ....................................... II Sound Pressure Level ...........................
PARTS DIAGRAM 12
PARTS LIST No 1 Description Cable Part number KPECSS1001 No Description Part number 39 Nut M6 KPECSS1039 2 Strain Relief KPECSS1002 40 Nut M6x12 KPECSS1040 3 Cable Pressboard KPECSS1003 41 Chain Guide KPECSS1041 4 Screw ST 4x14 KPECSS1004 42 Bolt M5x35 KPECSS1042 5 Capacitance 0.
DECLARATION OF CONFORMITY 14
NOTES 15
