Order Parts Here: Rider Scrubber www.ivie-ent.com/parts Ph:(918)254-5161 Rotary, Cylindrical and (Power steering) Operator's Manual Manuel d'utilisation Libro de Instrucciones U.S. Patent No. 6,105,192; No. 6,493,896; No. 6,557,207; No. 7,041,029 and Patents Pending Canada Patent No.
ENGLISH EN Table of Contents Operator Safety Instructions .................................................................................................................................................. Introduction & Machine Specifications .................................................................................................................................... Symbols Used on Focus ................................................................................................................
ENGLISH EN OPERATOR SAFETY INSTRUCTIONS Clarke® DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner's Manual and on your machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Owner's Manual and on your machine.
ENGLISH EN WARNING: Any alterations or modifications of this machine could result in damage to the machine or injury to the operator or other bystanders. Alterations or modifications not authorized by the manufacturer voids any and all warranties and liabilities. WARNING: Electrical components of this machine can "short-out" if exposed to water or moisture. Keep the electrical components of the machine dry. Wipe the machine down after each use.
ENGLISH EN Introduction Introduction & Machine Specifications This is a floor cleaning machine which, using the mechanic or abrasive action of brushes or pads and the chemical action of a water-detergent solution, is able to clean any type of floor. During its forward movement, it picks up the removed dirt and the detergent solution which has not been absorbed by the floor.
ENGLISH EN Symbols Used On FOCUS Rider Horn Button One Touch Brush Up/Down Traverse Speed On/Off Switch Squeegee Up/Down i-Drive Directional Guide Solution Flow Switch Recovery / Solution LED Battery Meter Warning Label LCD Display Button Page -6- Clarke® Operator's Manual (EN) - Focus Rider
ENGLISH EN Display Screens For FOCUS Rider Traverse speed indicator 1 = low 0-2 mph 2 = med 0-3 mph 3 = high 0-4 mph Position arrow indicating current position of squeegee (up or down) Indicators are on, showing current settings. SCREEN 1 Water “droplets” off when solution is off and they are flashing when solution is on. Screens Available to Operator “Battery” blinks when low voltage occurs. Arrows indicating vacuum status. They are flashing when vac is on and off when vac is off.
ENGLISH EN Machine Control Panel On/Off Key Switch (See figure 1, Item D) The key switch turns “ON” the power to the control panel. “O” is the “OFF” and “I” is the “ON”. Brush Up/Down Switch (See figure 1, Item A) To lower brush head, push the brush switch in the down (+) position. To lower the brush head to maximum brush pressure, continue to hold the switch in the down (+) position until the travel stops.
ENGLISH EN i-Drive Controls Horn Button (See figure 2, Item A) The machine is equipped with a horn and is activated by the red button located on the top of the joystick. The horn will sound continuously when pressed. A B One Touch (See figure 2, Item B) The one touch button is a green button located on the upper front of the joystick. NOTE: For more information about the one touch feature see the section titled “How to Operate the Machine”.
ENGLISH EN How To Prepare the Machine For Operation How To Handle the Packed Machine The machine is packed in a specific package provided on a pallet so that it can be moved with a forklift. WARNING: BATTERY CONNECTIONS Front of machine The packages cannot be placed on top of each other. How to Unpack the Machine 1. Remove the outer package. 2. The machine is fixed on the pallet with banding straps and wooden blocks to prevent movement during shipment. Remove the bands and blocks. 3.
ENGLISH EN How To Prepare the Machine For Operation Battery Maintenance The electrical power to operate the machine comes from the storage batteries. Storage batteries need preventative maintenance. Correct Fill WARNING: Working with batteries can be dangerous. Always wear eye protection and protective clothing when working near batteries. NO SMOKING! To maintain the batteries in good condition, follow these instructions: 1. Keep the electrolyte at the correct level.
ENGLISH EN How To Prepare the Machine For Operation How to Charge the Batteries WARNING: Charging the batteries in an area without adequate ventilation could result in an explosion. To prevent an explosion, charge the batteries only in an area with good ventilation. WARNING: Lead acid batteries generate gases which could explode. Keep sparks and flames away from batteries. NO SMOKING! To charge the batteries, follow this procedure: 1. Make sure the key switch is in the “OFF” position. 2.
ENGLISH EN How To Prepare the Machine For Operation How To Install the Squeegee To install the squeegee onto the machine, follow this procedure: 1. The squeegee assembly has a break away feature that is also used for mounting the squeegee. Loosen the knobs on the squeegee (figure 8). Slide the stud into the slotted hole in the support frame on the machine. 2. Attach the vacuum hose cuff to the squeegee hose fitting (see figure 9). 3. Figure 8 Tighten knobs.
ENGLISH EN How To Prepare the Machine For Operation How To Change or Rotate Brushes on Cylindrical Brush Head To install or rotate brushes on the cylindrical brush head: 1. Raise the brush deck and turn the key switch “OFF”. 2. Raise the brush skirt and pull out to remove. See figure 11. Figure 11 3. Remove thumb screw from brush door. See figure 12. 4. Lower door approximately 1/2 inch and slide door and hub assembly from brush. See figure 13. 5. Slide brush off hub at opposite end. See figure 14. 6.
ENGLISH EN How To Prepare the Machine For Operation How To Install The Brush Or Pad on the BOOST machine To install the brush or pad on the BOOST machine, follow this procedure: 1. Turn the key switch "ON". 2. Put the brush switch in the "UP" position. 3. Turn the key switch "OFF". 4. Go to the side of the machine. 5. Press on a brush or pad under the flex plates. See figure 15. Figure 15 NOTE: When using a black pad, position pad on head.
ENGLISH EN How To Operate The Machine How to Operate the i-Drive Controls The following controls are located on the joystick: 1. Horn : The horn is a red button located on the top of the joystick (figure 17, item A). NOTE: The horn sounds continuously when pressed and intermittent and automatic in reverse. A B 2. 3. One Touch: The one touch button is a green button located on the upper front of the joystick (figure 17, item B). NOTE: For more information about the one touch control see below.
ENGLISH EN How To Operate The Machine (Top View) How to Return One Touch to Factory Default Settings To restore the factory settings, follow the procedures below: 1. A Press and hold the green one touch button (figure 17, B) until you hear a double beep from the machine. NOTE: The time required for this will be approximately 15 2. seconds. The settings should be returned to 2 bars of solution and 1 bar of brush pressure.
ENGLISH EN How To Operate the Machine Seat Adjustment (Standard) The standard seat is not adjustable forward or backward. Seat Adjustment (Deluxe) The optional deluxe seat is adjustable in three ways: 1. The seat can be adjusted to the forward/backward position by using the lever on the lower right side of the seat . Moving the lever will allow the seat to slide into the preferred position. See figure 20. 2.
ENGLISH EN How To Operate the Machine SCREEN 1 How to Read the Battery Meter (see figure 22, A) The battery meter is an indicator on the LCD display. This indicator is on the LCD display on the front of the machine. It has 10 bars with 10 bars visible indicating a full charge. As you run the machine the bars will begin to lower. The “Battery Icon” (B) will begin to flash to indicate you are reaching the end of charge.
ENGLISH EN How To Operate the Machine How to Operate the Squeegee and the Vacuum Motor The squeegee wipes the floor while the vacuum motor removes the dirty solution from the floor. To operate the squeegee, follow this procedure: 1. To lower the squeegee and start the vacuum motor, press the squeegee up/down switch to the down position (figure 25). NOTE: The vacuum motor will start immediately when the down position of the switch is pressed, and the squeegee will lower. 2.
ENGLISH EN How To Operate the Machine How to Fill the Solution Tank The solution tank fill port is located at the left side of the machine (see figure 29). To fill the solution tank, follow this procedure: 1. Turn the key switch to the “OFF” position. 2. Remove lid. 3. Add a cleaning chemical to the solution tank. For the correct amount of chemical, follow the directions shown on the container.
ENGLISH EN How To Operate the Machine (cont.) To traverse the machine follow this procedure: 1. Sit on the driver seat. NOTE: The machine will not traverse if the operator is not properly seated. 2. Turn the key switch to the “ON” position. 3. Raise the brush to the highest position (if necessary). 4. Raise the squeegee (if necessary). 6. Gently press on the joystick in the direction you want to travel. The machine will begin to move. 7. To change the speed of the machine move the joystick.
ENGLISH EN How To Operate the Machine How to Clean a Floor WARNING: Water solutions or cleaning materials used with this type of machine can leave wet areas on the floor surface. These areas can cause a dangerous condition for the operator or other persons. Always put CAUTION signs near the area you are cleaning. For one touch automatic cleaning follow this procedure: 1. Turn the key switch to the “OFF” position. 2. Put the water and a cleaning chemical in the solution tank. 3.
ENGLISH EN How To Operate the Machine How to Clean a Very Dirty Floor To clean a very dirty floor, follow this procedure: 1. Apply solution to the floor. 2. Do not lower the squeegee. This will keep the vacuum motor off. 3. Lower the brush or pad and scrub the floor. 4. Scrub the floor again with additional solution and lower the squeegee. 5. Pick up all the solution with the squeegee.
ENGLISH EN How To Operate the Machine 11. Rinse the tank. Put clean water in the tank through the opening at the top. Be careful not to allow water into the vacuum intake tube (with screen). 12. If the tank or drain hose has an obstruction, use water pressure to flush the tank or hose. Put the water hose into the drain hose. NOTE: Do not place water hose into standpipe. 13. Leave the tank and drain plug removed to air dry. 14. Check the squeegee blade. Use a cloth to clean the squeegee blade.
ENGLISH EN Maintenance Maintenance To Be Done Every Week WARNING: Maintenance and repairs must be done by authorized personnel only. Always empty the solution tank and the recovery tank before doing any maintenance. Keep all fasteners tight. WARNING: Always wear eye protection and protective clothing when working near batteries. NO SMOKING! Do not put tools or other metal objects across the battery terminals or the tops of the batteries.
ENGLISH EN Maintenance 5. Clean the hose fitting in the recovery tank and spray water down the squeegee hose to clean out debris. 6. Reattach the squeegee hose. Cleaning the Solution Tank and Filter 1. Move the machine so that the solution tank filter assembly is located directly over a floor drain. 2. Turn the key switch to the “OFF” position. 3. Clean inside the solution tank with a jet stream of water. 7. Close the solution flow valve. 8.
ENGLISH EN Maintenance Rear Squeegee Blade Replacement If the rear squeegee blade is worn and does not dry the floor well, follow this procedure: 1. Remove the squeegee assembly from the machine. 2. Remove the squeegee blade and inspect it. 3. Rotate the squeegee blade to obtain a new cleaning edge. Replace if necessary. 4. Reinstall the squeegee blade. Figure 39 5. Reinstall the squeegee assembly on the machine. 6. Readjust the settings on the squeegee as required (see “How to Adjust Squeegee”).
ENGLISH EN Maintenance 3. Using the joystick, position the front wheel straight by doing one of the following: a) Using black indicator marks on steering system, realign front wheel (see figure 43). b) Place front wheel straight by visually estimating it’s position (see figure 44). 4. Hold joystick in corrected position and connect black wires together and key off the machine (see figure 45). 5. Disconnect black wires. Figure 43 6. Key machine on. If machine drives straight, then proceed to step 7.
ENGLISH EN HOW TO CORRECT PROBLEMS IN THE MACHINE PROBLEM Insufficient water onto the brushes The machine does not clean satisfactorily CAUSE ACTION The solution flow is not set Make sure the solution flow is set. There is no water in the solution tank. Fill the solution tank. The solution filter is dirty. Clean the solution filter. A circuit breaker has tripped. Reset the circuit breaker. Insufficient flow. Increase flow with solution switch. The brushes are worn.
ENGLISH EN FOCUS Rider Scrubber Common Error Codes ERROR CODE Clarke® CAUSE ACTION 1500 1501 1507 Check brake and wiring for short circuit. Make sure manual override is not engaged. 1600 High battery voltage. Poor or corroded connection to the battery. 3100 3101 3102 3103 3104 3105 Probable short circuit of output device. Check the traction, brush and vac motor connections on the trio and check wiring from these connectors down to the traction, brush and vac motors.
ENGLISH EN Accessories and Options - 7/06 BRUSHES AND PAD DRIVERS PART NO. 17521C 10383A 11431B 11426B 11427B 10874A PART NO. 17520C 10384A 11430B 11425B 11424B 10875A PART NO. 30614A 30615A 30616A 30617A 30619A PART NO. 997004 997003 997005 997007 28” Disc Model DESCRIPTION Pad Driver Assembly (2 req.) Lite Grit Disc Brush (2 req.) Clean Grit Abrasive (2 req.) Supergrit (2 req.) Polypropylene (2 req.) Nylon (2 req.) 34” Disc Model DESCRIPTION Pad Driver Assembly (2 req.) Lite Grit Disc Brush (2 req.
Rider Scrubber Section II Parts and Service Manual (70879B) U.S. Patent No. 6,105,192; No. 6,493,896; No. 6,557,207; No. 7,041,029 and Patents Pending Canada Patent No.
Clarke® FOCUS Rider Scrubber Final Assembly Drawing 8/06 16 1 3 11 12 14 2 4 5 18 15 6 17 13 7 10 9 8 8B Page -98- 8A Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber Final Assembly Parts List 8/06 Ref 1 Qty Qty Rotary Cyl. 1 - Qty. Boost - Part No. 10783A Description Tank, Recovery (Assembly) 10990A Tank, Recovery (Assembly) - 1 1 2 10784A Tank, Solution (Assembly) 1 1 1 3 10782A Plate, Electrical (28”) 1 - - 10961A Plate, Electrical (34”) 1 - - 10989A Plate, Electrical (Cyl.) - 1 1 10778A Mainframe, Main Asm.
Clarke® FOCUS Rider Scrubber Main Frame Assembly Drawing (Rotary) 8/06 Drawing #10778A 2 1 3 4 1A, 1B 25 8 9 10 10 37 9 17 20 7 26 42 24 11 23B 23 22 12 13 9 21 10 20 19 14 18 28 10 9 17 16 15 28 29 27 29 30 40 31 29 5 39 38 30 A Page -100- See Detail A 7 32 33 34 35 7 41 36 6 6 Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber Main Frame Assembly Parts List (Rotary) 8/06 Drawing # 10778A Ref 1 1A 1B 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 23B 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 NI Part No.
Clarke® FOCUS Rider Scrubber Main Frame Assembly Drawing (Cylindrical and BOOST) 8/06 Drawing #10949A 1 2 3 4 1A, 1B 25 10 8 9 9 10 20 17 23B 24 16 22 23 11 5 7 6 21 13 20 9 10 19 12 18 17 28 29 27 29 29 9 10 15 14 33 30 30 28 35 26 A Page -102- 34 See Detail A 30 32 6 Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber Main Frame Assembly Parts List (Cylindrical and BOOST) Drawing # 10949A Ref 1 1A 1B 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 23B 24 25 26 27 28 29 30 31 32 33 34 35 Part No.
Clarke® 17 16 1 15 2 3 12 4 14 5 6 6 13 12 7 11 10 9 8 FOCUS Rider Scrubber 28” & 34” Rotarty Models Optional Side Squeegee Lift Assembly Drawing 3/05 Page -104- Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber 28” & 34” Rotarty Models Optional Side Squeegee Lift Assembly Parts List 3/05 Ref 1 Part No. 87624A Description Washer, Nylon 1 1/2 x 1/4 x 1/8 2 3 86004A 920296 Screw, 1/4-20 x 1.50 HHCS Nut, 10-24 Elastic Stop 1 1 4 5 61699A 962798 Bracket, Sq.
Clarke® FOCUS Rider Scrubber Front Wheel Assembly Drawing and Parts List 6/04 Drawing #10779A 1 3 2 4 5 13 6 12 11 10 9 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 Page -106- Part No. 80267A 61472A 980645 170883 85822A 80268A 61483A 81221A 61382A 61474A 53437A 61484A 85838A 8 Description Bolt, 3/4 - 16 Hex Head Yoke Weldment, Steering Washer, 3/8 Flat Washer, Lock 3/8 Screw, 3/8 -16 x 7/8 Hex Hd. Nut, .
Clarke® FOCUS Rider Scrubber Squeegee Lift Assembly Drawing and Parts List 4/06 Drawing #10787A / 10949A 3 5 4 6 7 8 9 2 1 10 16 11 12 29 13 28 27 30 26 14 25 15 24 16 17 23 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part No.
Clarke® FOCUS Rider Scrubber Recovery Tank Assembly Drawing 5/05 Drawing #10783A / 10990A 1 2 3 4 5 6 7 8 9 10 11 44 43 42 12 41 13 40 14 39 15 38 37 16 17 20 22 18 23 19 36 21 6 24 35 25 34 26 30 33 29 32 Page -108- 28 27 26 31 Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber Recovery Tank Assembly Parts List 5/05 Drawing # 10783A / 10990A Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23* 24* 25* 26 27* 28 29 30* 31 32 33 34 35 36* 37* 38* 39 40 41 42* 43 44 NI NI Part No.
Clarke® FOCUS Rider Scrubber Solution Tank Assembly Drawing (View 1 of 2) 8/06 Drawing # 10784A 1 29 2 3 4 28 6 27 7 5 26 8 2 9 10 25 11 12 6 8 13 9 14 24 23 See Detail A 22 18 17 15 16 15 19 21 15 20 15 A Page -110- 2 3 26 Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber Solution Tank Assembly Parts List (View 1 of 2) 8/06 Drawing # 10784A Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Part No.
Clarke® FOCUS Rider Scrubber Solution Tank Assembly Drawing (View 2 of 2) 8/06 Drawing # 10784A 1 2 3 1 4 5 19 18 6 7 8 9 10 11 12 13 17 14 15 16 Page -112- Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber Solution Tank Assembly Parts List (View 2 of 2) 8/06 Drawing # 10784A Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Part No. 962957 87036A 30578A 30539B 61574A 31242A 61563A 40876A 30564A 980645 170883 85704A 722030 55189A 61561A 30597A 30596A 61557A 85398A Description Screw, 10-16 x 1.2 Self Tap Washer, #10 Flat Gasket, Solution Tank Fill Lid, Solution Bracket, Tank Fill Gasket Bushing Washer, Sight Tube Sensor, Water Level Hose, Solution Sight Washer, 3/8” S.A.E.
Clarke® FOCUS Rider Scrubber Front Cover Assembly Drawing and Parts List (Rotary) 4/06 Drawing # 11105A 1 2 3 17 16 4 5 6 7 8 8 15 9 7 8 14 10 12 13 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Page -114- Part No. 61556A 40880A 84237A 70808A 30529A 962157 170883 980645 920260 41448B 41423B 85737A 980657 53448A 962522 920722 40879A 11 Description Plate, Front Module Panel, LCD Control (Trio) Screw, 10-32 x .50 PH Label, Solution Level (Option) Cover, Front Screw, 5/16-18 x 1.25 Hex Hd.
Clarke® FOCUS Rider Scrubber Front Cover Assembly Drawing and Parts List (Cylindrical) 4/06 Drawing # 11106A 1 2 3 17 16 4 5 1 6 7 8 15 9 7 8 10 14 12 13 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Part No. 61556A 40880A 84237A 70808A 30529A 962157 170883 980645 920260 41423B 41448B 85737A 980657 53448A 962522 920722 40879A 10 11 Description Plate, Front Module Panel, LCD Control (Trio) Screw, 10-32 x .50 PH Label, Solution Level (Option) Cover, Front Screw, 5/16-18 x 1.25 Hex Hd.
Clarke® FOCUS Rider Scrubber 28” Rotary Brush Head Assembly Drawing and Parts List 8/05 Drawing #10697A 5 2 3 4 1, 1A 6 28 7 8 29 9 11 10 27 12 26 13 25 30 24 23 16 22 2 17 21 14 18 20 19 . NI = Not illustrated Ref 1 1A 2 3 4 5 6 7 8 9 10 11 12 13 14 16 Page Part No.
Clarke® FOCUS Rider Scrubber 34” Rotary Head Assembly Drawing and Parts List 8/05 Drawing #10698A 2 1, 1A 3 4 5 28 6 7 9 8 10 29 11 27 12 26 13 25 24 30 4 23 14 22 21 20 19 18 17 16 NI = Not illustrated Ref 1 1A 2 3 4 5 6 7 8 9 10 11 12 13 14 16 Part No.
Clarke® 26 33 36 35 30 50 Assembled View 23 20 42 22 17 43 44 41 40 39 10 38 45 46 26 47 48 49 2 34 4 1 1 2 32 37 31 30 29 3 5 28 4 14 6 27 7 9 8 10 25 13 11 12 14 24 23 15 7 22 21 16 17 18 19 20 FOCUS Rider Scrubber 28” Cylindrical Head Assembly Drawing 3/05 Drawing #10962A Page -118- Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber 28” Cylindrical Head Assembly Parts List 3/05 Drawing #10962A Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Part No.
Clarke® FOCUS Rider Scrubber 32” BOOSTTM Head Assembly Drawing 8/06 Drawing #11103A 1 34 33 2 32 31 30 3 29 28 27 26 25 4 5 24 23 22 21 20 6 19 7 18 8 9 17 10 11 12 13 16 15 Page -120- 14 Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber 32” BOOSTTM Head Assembly Parts List 8/06 Drawing #11103A Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Part No.
Clarke® FOCUS Rider Scrubber Squeegee Assembly Drawing 8/06 1 2 21 6 19 3 4 4 5 18 20 21 17 7 8 9 10 11 12 13 22 14 16 15 Page -122- Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® Ref. # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Part No.
Clarke® FOCUS Rider Scrubber Front Squeegee Assembly Drawing and Parts List 8/05 (Rotary Machines Only) Drawing # 10694A 2 15 3 1 4 5 6 14 13 7 12 8 11 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Page -124- Part No. 80275A 53185A 30048A 61496A 81104A 59932A 30540A 50835A 930086 61495A 53444A 53443A 30541A 80270A 30569A 9 10 Description Screw, 1/4 - 14 x 3/4 Ring, Retainer Wheel, Guide Weldment, Fr.
Clarke® FOCUS Rider Scrubber Front Squeegee Arm Assembly Drawing and Parts List 2/05 (Rotary Machine Only) Drawing # 10696A 1 2 3 4 5 6 7 Ref 1 2 3 4 5 6 7 NI Part No. 61548A 81112A 67867A 60256A 980651 85811A 53491A 61370A Description Arm, Weldment Squeegee Nut, 5/16-18 Thin ESNA Spacer, Squeegee Swivel Arm, Squeegee Pivot Washer, 5/16 Flat Screw, 5/16-18 x 3/4 Hex Head Pin, Quick Release Weight Qty 1 2 1 1 3 2 1 * * Optional - Not supplied with machine.
Clarke® FOCUS Rider Scrubber Right Arm Control Assembly Drawing and Parts List 2/05 Drawing # 10781A 5 6 4 3 2 1 7 Ref 1 2 3 4 5 6 7 Part No. 920056 40875A 61555A 962738 70807A 85612A 30532A Description Nut, 6 - 32 ESNA Nylock Shield Weldment, Joystick Panel, Arm Rest Right Control Screw, 6 - 32 x 5/8 PH Label, Joystick Panel Screw, 10-24 x .
Clarke® FOCUS Rider Scrubber Left Arm Control Assembly Drawing and Parts List 6/06 Drawing # 10780E 3 5 2 6 8 7 9 4 1 Ref 1 2 3 4 5 6 7 8 9 Part No. 30533A 40706A 40786A 40786S 40885A 40890A 61754A 71029A 85612A Description Arm. Control Left Switch, Momentary Push Switch, CE Key Spacer, Key Switch Switch, Momentary Rocker Switch, Maintained Rocker Panel, CE Arm Rest Control Label, CE Control Panel Screw, 10-24 x .
Clarke® FOCUS Rider Scrubber Electrical Panel Assembly Drawing and Parts List 3/06 Drawing # 10782A 5 1 9 7 6 2 3 2 8 10 2 3 11 4 3 2 12 13 15 14 15 17 15 18 16 NI = Not illustrated Ref 1 2 3 4 5 6 7 8 9 10 11 12 12 Page Part No. 40872B 40785A 87026A 980657 962086 980614 854849 83302A 81104A 40891A 41801A 962430 40878C 40769C -128- Description Qty Harness, Main Power (Rotary) 1 Harness, Main Power (Cyl.
Clarke® FOCUS Rider Scrubber Vac Motor Assembly #45019A 6/04 13 18 2 1 14 4 3 6 15 5 16 7 8 14 9 15 19 14 10 11 17 12 Ref # 1 2 3 4 5 6 7 8 9 10 Part No. 51913A 54809A 53905A 85303A 40830A 51914A 50618A 53100A 902679 902648 Description Clip (optional) Housing Fan Screw - 8-32 x 3/8 Carbon Brushes Clamp Bracket Disc Bearing - Ball Bearing - ball, radial Qty 2 1 1 4 2 2 1 1 1 1 Clarke® Operator's Manual - Focus Rider Scrubber Ref # 11 12 13 14 15 16 17 18 19 Part No.
Clarke® FOCUS Rider Scrubber Electrical Connection Diagram 9/04 Drawing # 70794A (pages 130-133) Page -130- Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber Electrical Connection Diagram 9/04 Drawing # 70794A (pages 130-133) Clarke® Operator's Manual - Focus Rider Scrubber Page -131-
Clarke® FOCUS Rider Scrubber Electrical Connection Diagram 9/04 Drawing # 70794A (pages 130-133) Page -132- Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber Electrical Connection Diagram 9/04 Drawing # 70794A (pages 130-133) Clarke® Operator's Manual - Focus Rider Scrubber Page -133-
Clarke® FOCUS Rider Scrubber Electrical Schematic (pages 134-135) 9/04 Rider Electrical Options Page -134- Clarke® Operator's Manual -Focus Rider Scrubber
Clarke® FOCUS Rider Scrubber Electrical Schematic (pages 134-135) 9/04 Rider Electrical Options Clarke® Operator's Manual - Focus Rider Scrubber Page -135-
