GAS HEATERS MODEL NOS: DEVIL 700, 900/910SS,1600/ 1610SS & 2100 PART NOS: 6920182, 6920186, 6920188, 6920190, 6920192, &6920194 USER INSTRUCTIONS ORIGINAL INSTRUCTIONS DL0722 - ISS 5
INTRODUCTION Thank you for purchasing this CLARKE Gas Powered Heater. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
SAFETY INFORMATION WARNING: LACK OF VENTILATION CAN CAUSE CARBON MONOXIDE POISONING. WARNING: CARBON MONOXIDE POISONING CAN KILL. Signs of Carbon Monoxide poisoning are headaches, dizziness and/or nausea. Should anyone show these signs, they must GET FRESH AIR IMMEDIATELY. Turn off the heater and have it serviced before using again. Pregnant women, persons with a heart or lung condition, anaemia or under the influence of alcohol, or those at high altitude, are more likely to be effected by Carbon Monoxide.
• Never move, handle, replenish the gas supply or service the heater when it is hot, operating or plugged in. • Never attach the heater to any duct work, or impede air flow into or out of the heater. • Disconnect the heater from the power supply when not in use. • Use ONLY the factory pre-set regulator supplied with the heater. • If the heater works for long periods at maximum capacity, be aware that it is possible for ice to form on the gas cylinder due to excessive evaporation.
ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage. This product may be fitted with a non-rewireable plug.
UNPACKING When unpacking, check the heater for possible shipping damage. Should any damage be apparent, please notify your Clarke dealer immediately. Your heater is fully assembled,- only the electrical and gas supplies need connecting. Retain any plastic cover caps (attached to the inlet connector and hose/regulator assembly) for future storage. PROPANE GAS SUPPLY These heaters are designed for use with PROPANE GAS ONLY.
In order to reduce the risk of icing up when operating at long periods at maximum capacity, you should use a larger capacity gas bottle, or two/ three bottles in parallel, as shown in Fig 2. • The ‘Tee’ piece and ‘pigtails’ are readily available from your builders merchants or gas supplier. CHANGING GAS BOTTLES 1. Turn off the heater and disconnect from the electrical supply. 2. Close the gas valve on the bottle and unscrew the regulator, (left hand thread). 3.
PRINCIPLE OF OPERATION Understanding the basic operation of the heater will reinforce the need to maintain the unit in top condition at all times, whilst always observing the safety precautions. The heater comprises four basic systems: 1. The gas system. 2. The air system. 3. The ignition system. 4. The safety control system. AIR SYSTEM An axial fan, which is energised when switching on, provides the air flow through the combustion chamber to provide a stream of hot air from the heater.
IGNITION SYSTEM Ignition is automatic with this heater as soon as the gas valve button is depressed, with a continuous spark from the spark plug igniting the gas. As the thermocouple heats up, a low voltage is fed to the Flame Failure valve, causing the valve to open, so that after a few seconds, the gas valve button may be released and the flame is established.
8. When the burner remains lit, set the heater at the required level by turning the flame intensity control valve counter-clockwise. If the burner goes out, turn off the gas. Turn the gas valve fully clockwise to its lowest position. Check the fuel supply. If adequate fuel is available, re-start the heater from step 1. Should the flame extinguish when the ignition button is released, wait for 1 minute, before repeating the operation.
STORAGE CAUTION: DISCONNECT THE HEATER FROM THE PROPANE SUPPLY CYLINDER(S) 1. Store the propane gas cylinders in a safe manner outdoors and keep them below 100 oF (37 oC). 2. Place protective bags over fittings & connectors and store in a clean, dry place. 3. Fit the plastic cover caps which were removed when unpacking, over the connections they covered when received. 4. When removing from storage, always check inside of heater for debris/ foreign objects before returning to use.
TROUBLESHOOTING PROBLEM CAUSE REMEDY Motor does not start. No power. Check power supply, power cable and fuse, and replace if necessary. Faulty motor/capacitor. Fan Check & replace if blades bent. necessary. Lock out of appliance due Identify cause of overto overheating. Thermal cut- heating. Wait for 5 mins out in operation. and restart. If condition persists, contact your Clarke dealer for advice. Spark plug does not spark.
PROBLEM CAUSE REMEDY Burner starts but stops Thermocouple is not warm as the gas valve enough or is faulty. button is released. Weak gas supply. Repeat the starting operation, keeping the gas valve button depressed for longer. Increase flame intensity control valve setting. SPECIFICATIONS Model Number 700 900/910SS 1600/1610ss 2100 Dimensions (L x W x H) mm 425x215x340 500x215x370 500x215x370 640x220x385 5.3 kg 6.4 kg 6.4 kg 8.
PARTS DIAGRAM - DEVIL 700/900/910SS 14 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
PARTS LIST DEVIL - 700/900/910SS No Description No Description 1 Outer Shell 19 Spark Plug Washer 2 Handle Mounting clips 20 Spark Plug 3 Handle 21 Elbow Fitting 4 Middle Cylinder 22 Fuel Tube Assembly 5 Front Guard 23 Extension Fitting 6 Orifice Assembly 24 Securing Nut 7 Flame Holder Assembly 25 Gas Valve 8 Orifice Nut 26 Male Fitting Connector 9 High Limit Switch Bracket 27 Solenoid Valve Assembly 10 High Limit Switch 28 Solenoid Valve Assembly Nut 11 Thermoco
PARTS DIAGRAM - DEVIL 1600 16 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
PARTS LIST - DEVIL 1600 No Description No Description 1 Outer Shell 19 Thermocouple Bracket 2 Handle Mounting Clips 20 Thermocouple 3 Handle 21 Elbow Fitting 4 Middle Cylinder 22 Fuel Tube Assembly 5 Front Guard 23 Extension Fitting 6 Orifice Assembly 24 Securing Nut 7 Flame Holder Assembly 25 Gas Valve 8 High Limit Switch Bracket 26 Male Connector Fitting 9 Orifice Nut 27 Solenoid Valve Assembly 10 High Limit Switch 28 Solenoid Valve Assembly Nut 11 Spark Plug N
PARTS DIAGRAM - DEVIL 1610SS 18 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
PARTS LIST - DEVIL 1610SS No Description No Description 1 Outer Shell 19 Thermocouple Bracket 2 Handle Mounting Clips 20 Thermocouple 3 Handle 21 Elbow Fitting 4 Middle Cylinder 22 Fuel Tube Assembly 5 Front Guard 23 Extension Fitting 6 Orifice Assembly 24 Securing Nut 7 Flame Holder Assembly 25 Gas Valve 8 High Limit Switch Bracket 26 Male Fitting Connector 9 Orifice Nut 27 Solenoid Valve Assembly 10 High Limit Switch 28 Solenoid Valve Assembly Nut 11 Spark Plug
PARTS DIAGRAM - DEVIL 2100 20 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
PARTS LIST - DEVIL 2100 No Description No Description 1 Outer Shell 20 Thermocouple Bracket 2 Flame Control PCB Bracket 21 Thermocouple 3 Flame Control PCB 22 Orifice Nut 4 Handle Mounting Clips 23 Elbow Fitting 5 Handle 24 Fuel Tube Assembly 6 Middle Cylinder 25 Extension Fitting 7 Front Guard 26 Securing Nut 8 Orifice Assembly 27 Gas Valve 9 Spark Plug Nut 28 Male Fitting Connector 10 Flame Holder Assembly 29 Solenoid Valve Assembly 11 Spark Plug Washer 30 So
WIRING DIAGRAMS 22 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
DECLARATION OF CONFORMITY 23 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
